Indiacon CivilSubscribe

Textbook › Steel Design › Chapter 1 › Lesson 1.1

1.1 Structural steel and rolled sections

Steel Design Chapter 1: Materials and design basis Under review — not yet three-checked Author: Indiacon

Learning objectives

After this lesson you should be able to:

  • Describe the composition, tension-test behaviour and design properties of structural steel, using the physical properties fixed in IS 800:2007 cl. 2.2.4.1.
  • Pick the yield stress and ultimate stress of an IS 2062 grade from IS 800:2007 Table 1, allowing for the drop in yield stress with plate thickness.
  • Name the common hot-rolled shapes and compute the area, second moment of area, elastic and plastic section moduli, radius of gyration and mass per metre of an I-section from its dimensions.

Theory

Structural steel is iron with a small, controlled amount of carbon, usually well under a quarter of a percent in weldable grades, plus manganese and traces of other elements. That chemistry gives what a structural engineer wants: high strength, the same behaviour in tension and compression, ductility so that a member yields and deforms visibly before it breaks, toughness against sudden fracture and good weldability. Steel is made and rolled in mills under close quality control, so its properties vary far less than those of concrete or timber, and members are fabricated in workshops and erected quickly on site.

A tension test on a coupon cut from a plate or section shows the key properties. Stress rises in proportion to strain up to the yield stress fy; the slope is the modulus of elasticity E. Mild steel then shows a yield plateau, where strain grows several times over with no rise in stress, followed by strain hardening up to the ultimate tensile stress fu, and finally necking and fracture. The elongation at fracture is a measure of ductility. Design uses fy for strength checks such as yielding and buckling, and fu for rupture at bolt holes and in connections. Deflection is different: it is an elastic serviceability check that uses E, the section properties and the service loads, not fy. The elastic constants are almost the same for every grade, so a stronger steel carries more load but is no stiffer: deflection and elastic buckling do not improve with grade.

Structural steel: material and sectionfyfuplateauhardeningstrainstressslope EDbftftwrolled I-section
Figure 1.1: Tension-test curve of mild structural steel (elastic line, yield plateau, strain hardening to fu) and the dimensions of a rolled I-section. Indiacon original, not to scale.

IS 800:2007 cl. 2.2.2 requires the structural steel used in general construction to conform to IS 2062 before fabrication, and cl. 2.2.4.1 fixes the physical properties to be used for every grade: unit mass 7 850 kg/m³, E = 2.0 × 10⁵ N/mm², Poisson ratio 0.3, modulus of rigidity G = 0.769 × 10⁵ N/mm² and coefficient of thermal expansion 12 × 10⁻⁶ per °C. The grades are named by their minimum yield stress, for example E250 and E350. IS 800:2007 Table 1 (cl. 2.2.4.2) lists, for IS 2062 grade E250, a yield stress of 250 MPa for thickness below 20 mm, 240 MPa from 20 to 40 mm and 230 MPa above 40 mm, with ultimate tensile stress 410 MPa and elongation 23 per cent; for E350 the yield stress is 350, 330 and 320 MPa in the same bands with ultimate stress 490 MPa. Thick plates cool more slowly in the mill and end up with a coarser grain, which is why their yield stress is lower.

Edition note on IS 2062: IS 800:2007 refers to IS 2062 for structural steel, and its Table 1 values were written around the edition then in force. BIS notified IS 2062 (Part 1):2025 (eighth revision), established on 29 December 2025, and the notice set 29 June 2026 as the withdrawal date of IS 2062:2011 (Gazette of India, BIS notification dated 1 January 2026). This lesson quotes the grade values given in IS 800:2007 Table 1; before using them for a project, check the steel against the IS 2062 edition named in the contract and the mill test certificate, and confirm any change in grades or properties in the current BIS text.

Steel reaches site in standard rolled shapes so that designers choose a section from a table instead of designing one from scratch. IS 800:2007 cl. 1.6 requires rolled shapes, bolts, nuts and welds to conform to IS 808 and IS 1852 for dimensions, form, weight and tolerances. Each shape puts material where a particular job needs it. The I-section places most of the steel in two flanges far from the neutral axis, which makes it efficient in bending about its major axis; wide-flange column sections have broader flanges for stiffness about the minor axis as well. Channels serve as purlins, stair stringers and, in pairs, built-up columns. Angles are the workhorse of trusses, bracing and transmission towers because a bolt through one leg makes an easy connection. Hollow sections resist torsion and buckling well, and plates are cut and welded into girders, gussets and base plates.

Section tables list area, mass per metre, second moments of area Ix and Iy, elastic section moduli Ze, plastic section moduli Zp and radii of gyration r. The property that governs depends on the job: area for tension, Z for bending, r for buckling. In this lesson the properties of an I-section are worked out from its plate dimensions, ignoring the small root fillets of a rolled section, so every number can be checked by hand.

Derivation

  1. Modulus of rigidity: for an isotropic elastic material G = E/(2(1 + ν)). With E = 2.0 × 10⁵ N/mm² and ν = 0.3, G = 200 000/2.6 = 76 923 N/mm² = 0.769 × 10⁵ N/mm², the value given in IS 800:2007 cl. 2.2.4.1.
  2. Yield strain: Hooke's law σ = E ε holds up to yield, so εy = fy/E. For E250 steel εy = 250/200 000 = 0.00125.
  3. Second moment of area of a doubly symmetric I-section: take the full rectangle bf × D and subtract the two empty rectangles beside the web, total width (bf − tw) and height hw = D − 2 tf: Ix = [bf D³ − (bf − tw) hw³]/12.
  4. Elastic section modulus: the bending stress σ = M y/I is largest at the extreme fibre y = D/2, so the moment that first causes yield is fy Ix/(D/2) = fy Ze, with Ze = 2 Ix/D.
  5. Plastic section modulus: when the whole section has yielded, half the area is at +fy and half at −fy. The plastic moment is fy times the sum of the first moments of the two halves about the equal-area axis. For the I-section each flange area bf tf acts at (D − tf)/2 and each half web hw tw/2 acts at hw/4, giving Zp = bf tf (D − tf) + tw hw²/4.
  6. Shape factor: Zp/Ze measures the reserve of moment beyond first yield. For a solid rectangle b × d, Zp = b d²/4 and Ze = b d²/6, so the shape factor is 1.5; an I-section, with most of its steel already near the extreme fibres, has a shape factor of about 1.1 to 1.2.
  7. Free thermal movement and restrained stress: an unrestrained member changes length by ΔL = α L ΔT; if the movement is fully prevented, the strain α ΔT is locked in and the stress is σ = E α ΔT.
Formulas, symbols and SI units
  • Physical properties (IS 800:2007 cl. 2.2.4.1): ρ = 7 850 kg/m³; E = 2.0 × 10⁵ N/mm²; ν = 0.3; G = 0.769 × 10⁵ N/mm²; α = 12 × 10⁻⁶ per °C
  • Yield strain εy = fy/E (dimensionless; fy and E in N/mm²)
  • I-section: A = 2 bf tf + hw tw (mm²), hw = D − 2 tf (mm)
  • Ix = [bf D³ − (bf − tw) hw³]/12 (mm⁴); Iy = 2 tf bf³/12 + hw tw³/12 (mm⁴)
  • Ze = 2 Ix/D (mm³); Zp = bf tf (D − tf) + tw hw²/4 (mm³); r = √(I/A) (mm)
  • Mass per metre = A (m²) × 7 850 (kg/m³) (kg/m)
  • Thermal: ΔL = α L ΔT (mm); restrained stress σ = E α ΔT (N/mm²)
Assumptions and limits
  • Properties are nominal values used as characteristic values in design (IS 800:2007 cl. 2.1); actual mill-test values are usually higher.
  • The section properties here are for an idealised plate section with sharp corners; rolled sections have root fillets and, in some shapes, tapered flanges, so their tabulated properties differ slightly. Design uses the tabulated values for the section actually supplied.
  • Linear elastic behaviour up to fy is assumed for Ze, εy and thermal stress; Zp assumes a ductile steel with a yield plateau long enough for the whole section to yield.
  • The thickness bands of IS 800:2007 Table 1 are applied to the thickness of the element concerned (flange or web); when the flange and web of one section fall in different bands, the lower yield stress is commonly used for the whole section.
  • Steel loses strength and stiffness at high temperature and is prone to corrosion; the room-temperature properties above do not cover fire or corroded sections.

Codes and standards

Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.

  • IS 800:2007 cl. 2.1 (material properties are nominal values to be accepted as characteristic values), cl. 2.2.2 (structural steel in general construction to conform to IS 2062 before fabrication), cl. 2.2.3 (other steels only with suitably modified design provisions), cl. 2.2.4.1 (unit mass, E, Poisson ratio, G and coefficient of thermal expansion), cl. 2.2.4.2 with Table 1 (yield stress, ultimate stress and elongation of IS 2062 grades by thickness), cl. 3.4.4 (coefficient of thermal expansion as in cl. 2.2.4.1) and cl. 1.6 (rolled shapes, bolts, nuts and welds to IS 808 and IS 1852).
  • IS 2062 (hot rolled structural steel), IS 808 (dimensions of hot rolled beam, column, channel and angle sections) and IS 1608 (tensile testing of metals) are named by number only.
  • EN 1993-1-1 (Eurocode 3) takes steel grades and nominal properties from the EN 10025 product standards, again with the yield strength reducing in thickness bands. AISC 360 in the USA uses ASTM steels such as A992 for wide-flange shapes, with section dimensions and properties from the AISC Steel Construction Manual. The approaches are listed side by side, not ranked.

Worked examples

Example 1 (grade and thickness, exam style)

Problem. A girder is fabricated from IS 2062 grade E250 plates 12 mm, 25 mm and 45 mm thick. Find the yield stress to use for each plate and the corresponding design yield stress fy/γm0 with γm0 = 1.10 (IS 800:2007 Table 5), and the yield strain of the 12 mm plate.

  1. IS 800:2007 Table 1 for E250: fy = 250 MPa below 20 mm, 240 MPa from 20 to 40 mm, 230 MPa above 40 mm.
  2. 12 mm plate: fy = 250 MPa; fy/γm0 = 250/1.10 = 227.3 MPa.
  3. 25 mm plate: fy = 240 MPa; fy/γm0 = 240/1.10 = 218.2 MPa.
  4. 45 mm plate: fy = 230 MPa; fy/γm0 = 230/1.10 = 209.1 MPa.
  5. Yield strain of the 12 mm plate: εy = 250/200 000 = 0.00125; a 3 m length stressed to yield stretches 0.00125 × 3 000 = 3.75 mm.

Answer. fy = 250, 240 and 230 MPa; design yield stresses 227.3, 218.2 and 209.1 MPa; εy = 0.00125

Example 2 (section properties from dimensions)

Problem. An I-section is 400 mm deep with flanges 180 mm × 14 mm and a web 8 mm thick (root fillets ignored). Find A, Ix, Ze, Zp, the shape factor, Iy, rx, ry and the mass per metre.

  1. hw = 400 − 2 × 14 = 372 mm. A = 2 × 180 × 14 + 372 × 8 = 5 040 + 2 976 = 8 016 mm².
  2. Ix = [180 × 400³ − 172 × 372³]/12 = (1.152 × 10¹⁰ − 8.854 × 10⁹)/12 = 2.221 × 10⁸ mm⁴.
  3. Ze = 2 × 2.221 × 10⁸/400 = 1.111 × 10⁶ mm³.
  4. Zp = 180 × 14 × 386 + 8 × 372²/4 = 972 720 + 276 768 = 1 249 488 mm³ = 1.249 × 10⁶ mm³. Shape factor Zp/Ze = 1.12.
  5. Iy = 2 × 14 × 180³/12 + 372 × 8³/12 = 1.362 × 10⁷ mm⁴. rx = √(2.221 × 10⁸/8 016) = 166.5 mm; ry = √(1.362 × 10⁷/8 016) = 41.2 mm.
  6. Mass = 8 016 × 10⁻⁶ × 7 850 = 62.9 kg/m.

Answer. A = 8 016 mm², Ix = 2.221 × 10⁸ mm⁴, Ze = 1.111 × 10⁶ mm³, Zp = 1.249 × 10⁶ mm³ (shape factor 1.12), ry = 41.2 mm, 62.9 kg/m

Example 3 (thermal movement on site)

Problem. A steel roof rafter 30 m long is fixed against movement at both ends during erection. The steel warms by 35 °C in the afternoon sun. Find the free expansion if one end could slide, and the stress if both ends are fully restrained. Also confirm the value of G from E and ν.

  1. Free expansion ΔL = α L ΔT = 12 × 10⁻⁶ × 30 000 × 35 = 12.6 mm.
  2. Fully restrained stress σ = E α ΔT = 2.0 × 10⁵ × 12 × 10⁻⁶ × 35 = 84 N/mm².
  3. That is about a third of the 250 MPa yield stress of E250, from temperature alone, which is why long frames get expansion joints or sliding bearings.
  4. G = E/(2(1 + ν)) = 200 000/2.6 = 76 923 N/mm² = 0.769 × 10⁵ N/mm².

Answer. 12.6 mm free; 84 N/mm² if fully restrained; G = 0.769 × 10⁵ N/mm²

Step-by-step procedure

  1. Fix the steel grade (IS 2062 grade, for example E250 or E350) and the quality needed for welding or low temperature.
  2. For each element, read fy and fu from IS 800:2007 Table 1 using its thickness band; use the lower value if flange and web fall in different bands.
  3. Use the physical properties of cl. 2.2.4.1 (E, G, ν, α, unit mass) for every grade.
  4. Choose the shape that suits the job: I-sections for bending, wide flanges or hollow sections for columns, angles for truss members, channels for purlins.
  5. Read A, I, Ze, Zp and r from the section table, or compute them from the plate dimensions for a built-up section.
  6. Note the mass per metre for self-weight and for the cost estimate.

Site notes

  • Every lot of steel arriving on site should carry a mill test certificate giving heat number, grade, chemistry and tension-test results; the heat number stamped on the steel is matched to the certificate.
  • Section size, flange and web thickness, straightness and length are checked against the drawing and the rolling tolerances before fabrication starts.
  • Unidentified steel without a test certificate is kept aside; IS 800:2007 allows it only in unimportant members unless tests confirm its properties.
  • Steel is stacked off the ground on timber bearers, in the order of erection, to keep it straight and dry.
  • Thick plates for welded girders often need preheat before welding; the welding procedure is fixed from the steel chemistry and thickness.
Common mistakes
  • Using 250 MPa for a 25 mm or 45 mm E250 plate; the yield stress drops to 240 and 230 MPa in the thicker bands.
  • Choosing a higher grade to cure a deflection or buckling problem; E is the same for all grades, so only a stiffer section helps.
  • Mixing up Ze and Zp: Ze gives the moment at first yield, Zp the full plastic moment.
  • Forgetting the factor 4 in the web term of Zp (tw hw²/4), or using D instead of D − tf as the lever arm of the flanges.
  • Ignoring restrained thermal stress in long frames or in members fixed between rigid supports.
Quick check

A first check on an I-section: Zp/Ze should come out between about 1.1 and 1.2, and the mass in kg/m is about 0.785 times the area in cm². For Example 2: 1.249/1.111 = 1.12 and 0.785 × 80.16 = 62.9 kg/m. A shape factor near 1.5 means the section has been treated as a solid rectangle by mistake.

Summary

  • IS 800:2007 fixes E = 2.0 × 10⁵ N/mm², G = 0.769 × 10⁵ N/mm², ν = 0.3, α = 12 × 10⁻⁶ per °C and 7 850 kg/m³ for every grade.
  • IS 2062 steel is specified by grade; IS 800 Table 1 lists fy and fu, with fy dropping in the 20 to 40 mm and above 40 mm thickness bands.
  • Higher grades give strength, not stiffness.
  • Rolled shapes follow IS 808; the I-section is efficient in bending because its flanges are far from the neutral axis.
  • Ze = 2I/D gives first yield; Zp = bf tf (D − tf) + tw hw²/4 gives the plastic moment; their ratio for an I-section is about 1.1 to 1.2.

Practice questions

Tap a question to see the answer.

1Find the yield strain of grade E350 steel.

εy = 350/200 000 = 0.00175.

2Find the mass per metre of a flat 300 mm × 20 mm.

A = 6 000 mm² = 0.006 m²; mass = 0.006 × 7 850 = 47.1 kg/m.

3Show that G = 0.769 × 10⁵ N/mm² follows from the E and ν of IS 800.

G = E/(2(1 + ν)) = 2.0 × 10⁵/2.6 = 0.769 × 10⁵ N/mm².

4A 32 mm E250 plate is used in a girder flange. What yield stress and design yield stress (γm0 = 1.10) apply?

fy = 240 MPa (20 to 40 mm band); fy/γm0 = 218.2 MPa.

5Why does changing from E250 to E350 not reduce the deflection of a beam?

Deflection depends on E and I; E is the same 2.0 × 10⁵ N/mm² for all grades, so only a deeper or heavier section reduces it.

6Find the shape factor of a solid rectangular section.

Zp = b d²/4 and Ze = b d²/6, so Zp/Ze = 1.5.

References

Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.

  • N. Subramanian, Design of Steel Structures, Oxford University Press, New Delhi, 1st edition, 2008.
  • S. K. Duggal, Limit State Design of Steel Structures, McGraw Hill Education (India), 3rd edition, 2019.
Suggest a correction

If something on this page is wrong, tell the editor. Your message is sent privately and is not published.

Sent privately to the Indiacon editor; not published.