1.5 Thermal stresses
After this lesson you should be able to:
- Explain why a change of temperature causes stress only when the free expansion or contraction of a member is prevented.
- Derive and use σ = E α ΔT for a fully restrained bar, and adapt it for a gap or for supports that yield.
- Find the stresses in a composite bar of two materials with different coefficients of thermal expansion, and in a stepped bar held between rigid supports.
Theory
Almost every solid grows when it is heated and shrinks when it cools. Over the normal service range the change in length is proportional to the original length and to the change in temperature; the constant of proportionality is the coefficient of linear thermal expansion α. For structural steel α is about 12 × 10⁻⁶ per °C, so a 100 m steel girder grows by 12 mm for a 10 °C rise. This movement on its own is harmless: a bar that is free to expand changes length but carries no stress at all.
Stress appears only when something stops the movement. If a bar is held between two unyielding supports and then heated, the supports must push back hard enough to squeeze the bar back to its original length. The mechanical strain needed is equal and opposite to the thermal strain α ΔT, and Hooke's law turns that strain into a stress E α ΔT. The striking result is that this stress does not depend on the length or area of the bar, only on the material and the temperature change; the force, however, is the stress times the area, so a heavy section pushes much harder on its supports.
Real supports are rarely perfectly rigid. Bridge bearings slide, expansion joints open and close, foundations and abutments deflect, and fasteners slip in their holes. Whatever part of the free expansion the supports allow is subtracted before the stress is calculated. A gap left at the end of a rail or a slab works the same way: until the gap closes there is no stress, and afterwards only the extra expansion is resisted. This is why bridges have expansion joints and why rails are laid with planned gaps or are anchored at a chosen stress-free temperature.
When two materials with different α are joined so that they must move together, as with a steel tube filled with concrete or a bolt passing through a sleeve, a temperature change creates internal stresses even with no external restraint. The material that wants to expand more is held back and goes into compression; the other is stretched and goes into tension, and the two forces balance each other. Steel and concrete have similar α, which is one reason reinforced concrete works so well; a large mismatch would crack the concrete with every hot day.
Derivation
- Free thermal elongation: δ_T = α ΔT L, where ΔT is the temperature rise (negative for a fall).
- Fully restrained bar: the supports supply an axial force P so that the total elongation is zero: α ΔT L − PL/(AE) = 0.
- Solving: P = A E α ΔT, so the stress is σ = P/A = E α ΔT (compressive for a rise, tensile for a fall), independent of L and A.
- Gap or yielding support of total amount Δ: only (α ΔT L − Δ) is prevented, so σ = E(α ΔT L − Δ)/L when α ΔT L > Δ, and zero otherwise.
- Stepped bar between rigid supports (segments i in series): the same force P acts in every segment, and zero total elongation gives α ΔT ΣL_i = P Σ L_i/(A_i E_i), so P = α ΔT ΣL_i / Σ(L_i/(A_i E_i)); stress in each segment is P/A_i. For different materials replace α ΔT ΣL_i by ΔT Σ α_i L_i.
- Composite bar of materials 1 and 2 (α₂ > α₁) joined at the ends: equilibrium with no external load gives tension in 1 equal to compression in 2: σ₁A₁ = σ₂A₂ = F.
- Compatibility (equal final length): α₁ΔT + σ₁/E₁ = α₂ΔT − σ₂/E₂, so σ₁/E₁ + σ₂/E₂ = (α₂ − α₁)ΔT.
- Solving the two equations: F = (α₂ − α₁) ΔT · A₁E₁A₂E₂/(A₁E₁ + A₂E₂); then σ₁ = F/A₁ (tension) and σ₂ = F/A₂ (compression).
Free thermal strain ε_T = α ΔT; free elongation δ_T = α ΔT LFully restrained: σ = E α ΔT; force P = A E α ΔTWith gap or support yield Δ: σ = E(α ΔT L − Δ)/L (only if α ΔT L > Δ)Stepped bar between rigid supports: P = ΔT Σα_i L_i / Σ(L_i/(A_i E_i)); σ_i = P/A_iComposite bar: F = (α₂ − α₁) ΔT A₁E₁A₂E₂/(A₁E₁ + A₂E₂); σ₁ = F/A₁ tension, σ₂ = F/A₂ compression (α₂ > α₁, temperature rise)Units: α in per °C, ΔT in °C, E in N/mm², L and Δ in mm give σ in N/mm²
- The material stays linear elastic; the stresses found must be below the yield or cracking stress.
- α and E are taken as constant over the temperature range; both change at high temperatures, as in a fire.
- The temperature is uniform over the cross-section; a temperature gradient through the depth causes bending (curvature), which is a separate case.
- Restrained compression members are assumed not to buckle; long slender members, such as rails under heat, can buckle sideways before the full stress is reached.
- Supports are rigid unless a gap or yield is stated; in composite bars the materials are perfectly bonded or joined at the ends.
Codes and standards
Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.
- IS 800:2007 cl. 2.2.4.1 takes the coefficient of thermal expansion of structural steel, irrespective of grade, as 12 × 10⁻⁶ per °C, together with E = 2.0 × 10⁵ N/mm².
- IS 456:2000 cl. 6.2.6 gives the coefficient of thermal expansion of concrete according to the type of aggregate, ranging from about 0.6 × 10⁻⁵ per °C (limestone) to about 1.3 × 10⁻⁵ per °C (quartzite); the aggregate actually used should be identified before a value is chosen.
- Side by side: EN 1993-1-1 cl. 3.2.6 takes α = 12 × 10⁻⁶ per K for structural steel (up to 100 °C), and EN 1992-1-1 cl. 3.1.3 takes α = 10 × 10⁻⁶ per K for concrete unless better information is available. These are not ranked here.
- The temperature ranges themselves (seasonal and daily) come from local climate data and the loading code of each structure type, covered in the loading and bridge subjects.
Worked examples
Problem. A long welded steel rail of cross-sectional area 7700 mm² is fully restrained by its fastenings and ballast. It was fastened at its stress-free temperature, and the rail temperature later rises by 30 °C. Take E = 2.0 × 10⁵ N/mm² and α = 12 × 10⁻⁶ per °C. Find the stress and the axial force in the rail, and the movement that a free 1 km length would have had.
- Fully restrained, so σ = E α ΔT = 2.0 × 10⁵ × 12 × 10⁻⁶ × 30 = 72 N/mm² (compression).
- Axial force P = σ A = 72 × 7700 = 554 400 N ≈ 554 kN (compression).
- Free 1 km length: δ_T = α ΔT L = 12 × 10⁻⁶ × 30 × 1 000 000 mm = 360 mm.
- The large force explains why long welded track needs heavy sleepers, well-packed ballast and checks against sideways buckling in hot weather.
Answer. σ = 72 N/mm² compression; P ≈ 554 kN; a free 1 km rail would grow 360 mm
Problem. A steel bar 5 m long and 500 mm² in area is held between two supports. Its temperature rises by 40 °C, and the supports yield (move apart) by a total of 0.8 mm. Take E = 2.0 × 10⁵ N/mm² and α = 12 × 10⁻⁶ per °C. Find the stress and force in the bar, and compare with fully rigid supports.
- Free expansion δ_T = 12 × 10⁻⁶ × 40 × 5000 = 2.4 mm.
- Expansion prevented = 2.4 − 0.8 = 1.6 mm.
- σ = E × 1.6/L = 2.0 × 10⁵ × 1.6/5000 = 64 N/mm² (compression); P = 64 × 500 = 32 000 N = 32 kN.
- With rigid supports σ = E α ΔT = 2.0 × 10⁵ × 12 × 10⁻⁶ × 40 = 96 N/mm²; the yield of 0.8 mm removes one third of the stress.
Answer. σ = 64 N/mm²; P = 32 kN (96 N/mm² if the supports were rigid)
Problem. A short concrete-filled steel tube has a steel area of 3000 mm² (E = 2.0 × 10⁵ N/mm², α = 12 × 10⁻⁶ per °C) and a concrete area of 30 000 mm² (take E = 30 000 N/mm², α = 10 × 10⁻⁶ per °C). The two act together, and the member is heated uniformly by 30 °C with no external load. Find the stress in each material and the common strain.
- Steel wants to expand more (α larger), so steel is compressed and concrete is stretched.
- A₁E₁ (concrete) = 30 000 × 30 000 = 9.0 × 10⁸ N; A₂E₂ (steel) = 3000 × 2.0 × 10⁵ = 6.0 × 10⁸ N.
- F = (α₂ − α₁) ΔT × A₁E₁A₂E₂/(A₁E₁ + A₂E₂) = 2 × 10⁻⁶ × 30 × (9.0 × 10⁸ × 6.0 × 10⁸)/(15.0 × 10⁸) = 21 600 N.
- Steel σ = 21 600/3000 = 7.2 N/mm² (compression); concrete σ = 21 600/30 000 = 0.72 N/mm² (tension).
- Common strain = 12 × 10⁻⁶ × 30 − 7.2/2.0 × 10⁵ = 3.24 × 10⁻⁴ (check from concrete: 10 × 10⁻⁶ × 30 + 0.72/30 000 = 3.24 × 10⁻⁴).
Answer. Steel 7.2 N/mm² compression; concrete 0.72 N/mm² tension; common strain 3.24 × 10⁻⁴
Step-by-step procedure
- Find the free thermal elongation α ΔT L of each part, as if it were unrestrained.
- Decide what the supports or the other material allow: zero (rigid), a known gap or yield, or a compatible movement.
- Write equilibrium (the force is the same in members in series; forces balance in a composite bar with no external load).
- Write compatibility: total elongation equals what the supports allow, or both materials end at the same length.
- Solve for force and stresses; state tension or compression, and check against yield, cracking and buckling limits.
Site notes
- Bridge decks move every day; bearings and expansion joints are set at the temperature of installation using the expected range, so the setting temperature must be recorded on site.
- Long welded rails are fastened at a chosen stress-free temperature; fastening them on a cold morning leaves them in high compression on a hot afternoon, with risk of buckling.
- Concrete pavements and long walls need contraction and expansion joints; a slab cast in hot weather shrinks as it cools and cracks if it is restrained.
- Pipelines, handrails and cladding fixings need slotted holes or loops to let thermal movement happen without stress.
- Multiplying E α ΔT by the length; the stress of a fully restrained bar does not depend on length.
- Forgetting to subtract a gap or support yield before calculating stress, or applying the formula when the gap never closes.
- In composite bars, putting the material with the larger α in tension instead of compression for a temperature rise.
- Mixing ×10⁻⁵ and ×10⁻⁶ values of α, which gives an error of ten times.
- Ignoring buckling of a long restrained compression member under heat.
For steel with E = 2.0 × 10⁵ N/mm² and α = 12 × 10⁻⁶ per °C, full restraint gives about 2.4 N/mm² of stress per °C; a 40 °C change gives about 96 N/mm². Partial restraint or a gap always gives less.
Summary
- Free thermal strain α ΔT causes no stress; restraint does.
- Fully restrained bar: σ = E α ΔT, independent of length and area.
- A gap or yielding support Δ reduces the prevented expansion to α ΔT L − Δ.
- Composite bars: equal and opposite forces; the material with larger α is compressed on heating.
Practice questions
Tap a question to see the answer.
1A steel bar is fixed between rigid walls and heated by 50 °C. Take E = 2.0 × 10⁵ N/mm² and α = 12 × 10⁻⁶ per °C. Find the stress.
σ = 2.0 × 10⁵ × 12 × 10⁻⁶ × 50 = 120 N/mm² (compression).
2A concrete pavement panel 4.5 m long (take α = 10 × 10⁻⁶ per °C) warms by 25 °C. Find its free expansion.
δ = 10 × 10⁻⁶ × 25 × 4500 = 1.125 mm.
3A fully restrained steel rail cools 20 °C below its stress-free temperature. Find the stress (E = 2.0 × 10⁵ N/mm², α = 12 × 10⁻⁶ per °C).
σ = 2.0 × 10⁵ × 12 × 10⁻⁶ × 20 = 48 N/mm² (tension).
4A steel bar 2 m long has a gap of 0.5 mm at one end before it meets a rigid wall. It is heated by 40 °C. Find the stress (E = 2.0 × 10⁵ N/mm², α = 12 × 10⁻⁶ per °C).
Free expansion 0.96 mm; prevented 0.46 mm; σ = 2.0 × 10⁵ × 0.46/2000 = 46 N/mm² (compression).
5Does the thermal stress in a fully restrained bar depend on its length or its cross-sectional area?
Neither: σ = E α ΔT. The force on the supports, A E α ΔT, does increase with area.
6A stepped steel bar between rigid walls has two segments each 1 m long, of areas 1000 mm² and 500 mm², and is heated by 20 °C. Find the force and the stress in each segment (E = 2.0 × 10⁵ N/mm², α = 12 × 10⁻⁶ per °C).
P = 12 × 10⁻⁶ × 20 × 2000 / [(1000/1000 + 1000/500)/2.0 × 10⁵] = 32 kN; stresses 32 N/mm² and 64 N/mm² (compression).
References
Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.
- B. J. Goodno, J. M. Gere, Mechanics of Materials, Cengage Learning, 9th edition, 2018.
- R. C. Hibbeler, Mechanics of Materials, Pearson, 10th edition, 2016.
- F. P. Beer, E. R. Johnston, J. T. DeWolf, D. F. Mazurek, Mechanics of Materials, McGraw Hill, 8th edition, 2020.
- E. P. Popov, Engineering Mechanics of Solids, Prentice Hall, 2nd edition, 1998.