Indiacon CivilSubscribe

Textbook › Engineering Mechanics › Chapter 5 › Lesson 5.3

5.3 Composite and built-up sections

Engineering Mechanics Chapter 5: Moment of inertia Under review — not yet three-checked Author: Indiacon

Learning objectives

After this lesson you should be able to:

  • Find the centroid and second moment of area of composite sections such as T-beams, I-sections and built-up girders.
  • Organise the calculation in a table of A, ȳ, A ȳ, I_c and A d².
  • Find elastic section moduli for the top and bottom fibres.

Theory

Most structural sections are made of rectangles, triangles and circles joined together or cut away: T-beams and L-beams cast with a slab, rolled and welded I-sections, box girders, channels and plated sections. The second moment of such a composite area about any axis is the sum of the second moments of its parts about that same axis. Holes and cut-outs are included as negative parts.

Because each part has its own centroid, the calculation has two stages. First locate the centroid of the whole section with the composite method of lesson 4.3. Then transfer each part's centroidal second moment to the section centroid with the parallel axis theorem and add them up. Tabulating A, ȳ, A ȳ, I_c and A d² for each part keeps the work clear and easy to check.

neutral axisd₁d₂flange A₁web A₂I = Σ(I_c + A d²)Indiacon original, not to scale
Figure 5.3: A T-beam split into flange and web: each part is transferred from its own centroid to the section neutral axis by the parallel axis theorem. Indiacon original, not to scale.

For a doubly symmetric section such as an I-section, the centroid is at mid-depth and the second moment can be found as an outer rectangle minus the two rectangles that are missing beside the web. For an unsymmetric section such as a T-beam, the centroid shifts towards the larger flange and the distances to the top and bottom fibres differ.

The elastic section modulus is Z = I / y_max, where y_max is the distance from the centroidal axis to the extreme fibre. The bending stress at that fibre is M / Z. An unsymmetric section has two moduli, one for the top and one for the bottom, and the smaller one gives the larger stress.

Derivation

  1. Split the section into parts i with areas A_i and centroid heights y_i from a reference line.
  2. Section centroid: ȳ = Σ A_i y_i / Σ A_i.
  3. Each part has centroidal second moment I_ci about its own axis parallel to the reference line, at distance d_i = y_i − ȳ from the section centroid.
  4. By the parallel axis theorem for each part and the additivity of integrals, I = Σ (I_ci + A_i d_i²). Holes enter with negative A_i and negative I_ci.
  5. Section moduli: Z_top = I / (h − ȳ) and Z_bottom = I / ȳ when ȳ is measured from the bottom.
Formulas, symbols and SI units
  • ȳ = Σ A_i y_i / Σ A_i
  • I = Σ (I_ci + A_i d_i²), d_i = y_i − ȳ
  • Symmetric I-section: I = B H³/12 − (B − t_w) h_w³/12
  • Elastic section modulus: Z = I / y_max (mm³); bending stress σ = M / Z
Assumptions and limits
  • Parts are joined so that they act together (full shear connection between flange and web).
  • Root fillets and corner radii of rolled sections are ignored in hand calculations; published section tables include them, so table values differ slightly.
  • For reinforced concrete these are gross-section properties of the concrete outline; cracked and transformed sections are treated in RCC design.

Codes and standards

Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.

  • Dimensions and section properties of rolled steel beams, channels and angles are tabulated in IS 808:1989; IS 800:2007 uses elastic and plastic section moduli of these sections in member design.
  • IS 456:2000 cl. 23.1.2 gives the effective width of the flange of T-beams and L-beams cast monolithically with a slab; that width sets b of the flange part in a calculation like Example 1.

Worked examples

Example 1 (site style)

Problem. A T-beam has a flange 1000 mm wide and 120 mm thick and a web 300 mm wide, with an overall depth of 600 mm. Find the height of the centroid below the top, the gross second moment of area about the centroidal axis, and the section moduli for the top and bottom fibres.

  1. Flange: A₁ = 1000 × 120 = 120 000 mm², centroid 60 mm below the top. Web: A₂ = 300 × 480 = 144 000 mm², centroid 120 + 240 = 360 mm below the top.
  2. ȳ (from top) = (120 000 × 60 + 144 000 × 360) / 264 000 = 223.6 mm.
  3. Flange: I_c = 1000 × 120³/12 = 1.440 × 10⁸; d = 163.6 mm; A d² = 3.213 × 10⁹ mm⁴.
  4. Web: I_c = 300 × 480³/12 = 2.765 × 10⁹; d = 136.4 mm; A d² = 2.678 × 10⁹ mm⁴.
  5. I = 1.440 × 10⁸ + 3.213 × 10⁹ + 2.765 × 10⁹ + 2.678 × 10⁹ = 8.800 × 10⁹ mm⁴.
  6. Z_top = 8.800 × 10⁹ / 223.6 = 3.935 × 10⁷ mm³; Z_bottom = 8.800 × 10⁹ / 376.4 = 2.338 × 10⁷ mm³.

Answer. ȳ = 223.6 mm from top; I = 8.800 × 10⁹ mm⁴; Z_top = 3.935 × 10⁷ mm³, Z_bottom = 2.338 × 10⁷ mm³

Example 2 (exam style)

Problem. A welded I-section has two flanges 200 mm × 20 mm and a web 360 mm × 10 mm, overall depth 400 mm. Find I about the major axis, the section modulus and the radius of gyration. Then find I if a 250 mm × 12 mm plate is welded to the outside of each flange.

  1. Outer rectangle minus missing parts: I = 200 × 400³/12 − 190 × 360³/12 = 3.279 × 10⁸ mm⁴.
  2. Z = I / 200 = 1.640 × 10⁶ mm³; A = 2 × 4 000 + 3 600 = 11 600 mm², k = √(I/A) = 168.1 mm.
  3. Each plate: I_c = 250 × 12³/12 = 36 000 mm⁴, A = 3 000 mm², centroid 200 + 6 = 206 mm from the axis, A d² = 1.273 × 10⁸ mm⁴.
  4. I_plated = 3.279 × 10⁸ + 2 × (36 000 + 1.273 × 10⁸) = 5.826 × 10⁸ mm⁴; Z = 5.826 × 10⁸ / 212 = 2.748 × 10⁶ mm³.

Answer. I = 3.279 × 10⁸ mm⁴, Z = 1.640 × 10⁶ mm³, k = 168.1 mm; with plates I = 5.826 × 10⁸ mm⁴, Z = 2.748 × 10⁶ mm³

Step-by-step procedure

  1. Sketch the section, choose a reference line (top or bottom) and split it into simple parts; mark holes as negative.
  2. Tabulate A, y, A y for each part and find ȳ.
  3. Add columns for I_c and d = y − ȳ, then A d².
  4. Sum I_c + A d² for all parts.
  5. Find Z_top and Z_bottom from the extreme-fibre distances, and k if needed.

Site notes

  • For a T-beam the neutral axis of the gross section lies close to the flange, so the bottom fibre has the smaller section modulus and the larger tensile stress.
  • Adding cover plates to a steel girder raises I quickly because the plates sit far from the axis; this is a common way to strengthen existing girders.
  • Check flange widths against the effective-width rule of the design code before using a slab as a flange.
Common mistakes
  • Adding I_c values of parts without the A d² terms.
  • Using d measured from the reference line instead of from the section centroid.
  • Forgetting to subtract holes, or subtracting their area but not their second moment.
  • Using one section modulus for an unsymmetric section.
  • Using gross properties where the design method calls for cracked or transformed sections.
Quick check

Σ A_i d_i (with signs) must be zero about the section centroid; check it before summing the A d² terms.

Summary

  • Composite I = Σ (I_c + A d²) about the section centroid.
  • Locate the centroid first; holes are negative parts.
  • Symmetric I-sections: outer rectangle minus the missing rectangles.
  • Z = I / y_max; unsymmetric sections have two moduli.

Practice questions

Tap a question to see the answer.

1An I-section has flanges 150 × 15 mm and a web 270 × 8 mm (depth 300 mm). Find I about the major axis.

I = 150 × 300³/12 − 142 × 270³/12 = 1.046 × 10⁸ mm⁴.

2For the section above, find the elastic section modulus.

Z = 1.046 × 10⁸ / 150 = 6.972 × 10⁵ mm³.

3A 300 × 300 mm square has a central 100 mm diameter hole. Find I about a centroidal axis parallel to a side.

300⁴/12 − π × 100⁴/64 = 6.750 × 10⁸ − 4.909 × 10⁶ = 6.701 × 10⁸ mm⁴.

4An inverted T has a flange 400 × 100 mm at the bottom and a web 100 × 300 mm above it. Find the centroid height above the bottom.

ȳ = (40 000 × 50 + 30 000 × 250)/70 000 = 135.7 mm.

5Find I about the centroidal axis for the inverted T above.

400 × 100³/12 + 40 000 × 85.7² + 100 × 300³/12 + 30 000 × 114.3² = 9.440 × 10⁸ mm⁴.

References

Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.

  • F. P. Beer, E. R. Johnston, D. F. Mazurek, P. J. Cornwell, B. P. Self, Vector Mechanics for Engineers: Statics and Dynamics, McGraw Hill, 12th edition, 2019.
  • R. C. Hibbeler, Engineering Mechanics: Statics, Pearson, 15th edition, 2022 (published 2021).
  • J. L. Meriam, L. G. Kraige, J. N. Bolton, Engineering Mechanics: Statics, Wiley, 9th edition, 2018.
  • S. Timoshenko, D. H. Young, J. V. Rao, S. Pati, Engineering Mechanics (in SI units), McGraw Hill Education (India), 5th edition, 2013.
Suggest a correction

If something on this page is wrong, tell the editor. Your message is sent privately and is not published.

Sent privately to the Indiacon editor; not published.