Indiacon CivilSubscribe

Textbook › Strength of Materials › Chapter 1 › Lesson 1.3

1.3 Elastic constants and their relations

Strength of Materials Chapter 1: Simple stress and strain Under review — not yet three-checked Author: Indiacon

Learning objectives

After this lesson you should be able to:

  • Define the four elastic constants of an isotropic material: modulus of elasticity E, shear modulus G, bulk modulus K and Poisson's ratio ν.
  • Derive E = 2G(1 + ν) and E = 3K(1 − 2ν), and use them to find any two constants from the other two.
  • Apply the generalised Hooke's law to find strains and volume change of a member under two- or three-dimensional stress.

Theory

When a bar is stretched it does not only get longer; it also gets thinner. The lateral contraction is proportional to the axial extension, and the ratio of the two (taken as a positive number) is Poisson's ratio ν, after the French mathematician who studied it. For structural steel ν is about 0.3, for concrete about 0.15 to 0.2, and for rubber, which keeps its volume almost constant, very close to 0.5. Poisson's effect explains why a confined concrete core in a spiral-reinforced column is stronger: the spiral resists the lateral expansion that would otherwise split the concrete.

Three kinds of stiffness describe how a material resists three kinds of deformation. The modulus of elasticity E relates axial stress to axial strain in a simple tension or compression test. The shear modulus (modulus of rigidity) G relates shear stress to shear strain, as in a shaft in torsion or a rubber bearing pad sliding sideways. The bulk modulus K relates a uniform pressure on all faces to the resulting change in volume, as for water in a pipe or a specimen deep under the ground. Together with ν these are the four elastic constants.

+γ/2−γ/2ττγE = 2G(1 + ν)E = 3K(1 − 2ν)ε_lat = −ν εdiagonal strain τ(1 + ν)/EIndiacon original, not to scale
Figure 1.3: Pure shear on a square element and the relations between elastic constants. Indiacon original, not to scale.

For an isotropic material, which has the same properties in every direction, only two of the four constants are independent. This is not a matter of experiment but of geometry: pure shear on a square element is exactly the same state of stress as equal tension and compression on its diagonals, so G must be fixed once E and ν are known. Likewise, uniform pressure is three equal normal stresses, so K follows from E and ν. Timber, rolled sheets and fibre composites are not isotropic, and need more constants.

The relations also set physical limits. K must be positive, so 1 − 2ν > 0 and ν cannot exceed 0.5; a value of 0.5 means the material is incompressible. G must be positive, so ν > −1, although common construction materials all have ν between 0 and 0.5. For steel the relations give G ≈ 0.38 E and K ≈ 0.83 E. The generalised Hooke's law combines Poisson's effect in all three directions: each normal stress causes strain in its own direction and a Poisson contraction in the other two, and the strains are added by superposition.

Derivation

  1. Poisson's ratio: under axial stress σ, axial strain ε = σ/E and lateral strain ε_lat = −ν ε.
  2. Generalised Hooke's law by superposition: ε_x = [σ_x − ν(σ_y + σ_z)]/E, and similarly for ε_y and ε_z; shear strains γ = τ/G are independent of normal stresses.
  3. Volumetric strain for small strains: ΔV/V = ε_x + ε_y + ε_z = (1 − 2ν)(σ_x + σ_y + σ_z)/E. For a bar in simple tension this is ε(1 − 2ν).
  4. Bulk modulus: under uniform pressure p (σ_x = σ_y = σ_z = −p) the volumetric strain is −3p(1 − 2ν)/E. K = p/(ΔV/V magnitude) gives E = 3K(1 − 2ν).
  5. Shear modulus: a square element under pure shear τ has principal stresses +τ and −τ along its diagonals. The tensile diagonal strain is [τ − ν(−τ)]/E = τ(1 + ν)/E.
  6. Geometry of the same element: a shear strain γ lengthens the tensile diagonal by a strain of γ/2 (for small γ). With γ = τ/G, the diagonal strain is τ/(2G).
  7. Equating the two expressions: τ/(2G) = τ(1 + ν)/E, so E = 2G(1 + ν).
  8. Eliminating ν between the two relations: E = 9KG/(3K + G) and ν = (3K − 2G)/[2(3K + G)].
Formulas, symbols and SI units
  • Poisson's ratio ν = −ε_lat/ε_axial (dimensionless, 0 ≤ ν ≤ 0.5 for common materials)
  • Generalised Hooke's law: ε_x = [σ_x − ν(σ_y + σ_z)]/E (and cyclic); γ = τ/G
  • Volumetric strain e_v = ΔV/V = ε_x + ε_y + ε_z = (1 − 2ν)(σ_x + σ_y + σ_z)/E
  • Uniaxial bar: e_v = ε(1 − 2ν); ΔV = PL(1 − 2ν)/E
  • E = 2G(1 + ν); E = 3K(1 − 2ν); E = 9KG/(3K + G); ν = (3K − 2G)/[2(3K + G)]
  • Units: E, G, K in N/mm² (MPa) or GPa; ν has no units
Assumptions and limits
  • The material is homogeneous, isotropic and linear elastic; anisotropic materials (timber, laminated composites) need more than two constants.
  • Strains are small, so volumetric strain is the sum of the three normal strains and squares of strains are neglected.
  • Constants are short-term values; concrete under sustained load creeps, so its effective modulus is lower.
  • For concrete, cracking changes the effective Poisson's ratio; the relations apply to uncracked concrete only.
  • Temperature effects are not included here (lesson 1.5).

Codes and standards

Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.

  • IS 800:2007 cl. 2.2.4.1 takes, for structural steel of any grade, E = 2.0 × 10⁵ N/mm², Poisson's ratio 0.3 and modulus of rigidity G = 0.769 × 10⁵ N/mm²; these are consistent with G = E/[2(1 + ν)] = 2.0 × 10⁵/2.6.
  • IS 456:2000 cl. 6.2.3.1 gives the short-term modulus of concrete Ec = 5000 √fck; a Poisson's ratio for concrete is not taken from IS 456 here, and measured values of about 0.15 to 0.20 are typical.
  • Side by side: EN 1993-1-1 takes E = 210 000 N/mm² and ν = 0.3 for structural steel, giving G ≈ 81 000 N/mm²; EN 1992-1-1 cl. 3.1.3 takes Poisson's ratio 0.2 for uncracked concrete and zero where cracked. These are not ranked here.

Worked examples

Example 1 (site style)

Problem. A steel tie rod 25 mm in diameter and 2 m long carries a tension of 100 kN. Take E = 2.0 × 10⁵ N/mm² and ν = 0.3. Find the elongation, the decrease in diameter and the change in volume.

  1. A = π × 25² / 4 = 490.87 mm²; σ = 100 000 / 490.87 = 203.72 N/mm².
  2. ε = σ/E = 1.0186 × 10⁻³; elongation δ = 1.0186 × 10⁻³ × 2000 = 2.037 mm.
  3. Lateral strain = −ν ε = −3.056 × 10⁻⁴; decrease in diameter = 3.056 × 10⁻⁴ × 25 = 0.00764 mm.
  4. Volumetric strain e_v = ε(1 − 2ν) = 1.0186 × 10⁻³ × 0.4 = 4.074 × 10⁻⁴.
  5. V = 490.87 × 2000 = 981 748 mm³; ΔV = 4.074 × 10⁻⁴ × 981 748 = 400 mm³ (check: PL(1 − 2ν)/E = 100 000 × 2000 × 0.4 / 200 000 = 400 mm³). The volume increases.

Answer. δ = 2.04 mm; diameter decreases by 0.0076 mm; volume increases by 400 mm³

Example 2 (exam style)

Problem. A material has E = 200 GPa and G = 80 GPa. Find Poisson's ratio and the bulk modulus.

  1. From E = 2G(1 + ν): ν = E/(2G) − 1 = 200/160 − 1 = 0.25.
  2. From E = 3K(1 − 2ν): K = E/[3(1 − 2ν)] = 200 / (3 × 0.5) = 133.3 GPa.
  3. Check: 9KG/(3K + G) = 9 × 133.33 × 80 / (400 + 80) = 200 GPa.

Answer. ν = 0.25; K = 133.3 GPa

Example 3 (laboratory style)

Problem. A concrete cylinder of 150 mm diameter is loaded to 200 kN in compression. Strain gauges read an axial shortening strain of 3.9 × 10⁻⁴ and a lateral (hoop) strain of 0.75 × 10⁻⁴. Find E, ν and G for this concrete.

  1. A = π × 150² / 4 = 17 671 mm²; σ = 200 000 / 17 671 = 11.32 N/mm².
  2. E = σ/ε = 11.32 / 3.9 × 10⁻⁴ = 29 020 N/mm² ≈ 29.0 GPa.
  3. ν = 0.75 × 10⁻⁴ / 3.9 × 10⁻⁴ = 0.192.
  4. G = E/[2(1 + ν)] = 29 020 / (2 × 1.192) = 12 170 N/mm² ≈ 12.2 GPa.

Answer. E ≈ 29.0 GPa; ν ≈ 0.19; G ≈ 12.2 GPa

Step-by-step procedure

  1. Write down which constants are known (usually E and ν from tests or code values).
  2. Find the others from E = 2G(1 + ν) and E = 3K(1 − 2ν); check that ν is between 0 and 0.5.
  3. For a multi-axial stress state list σ_x, σ_y, σ_z (tension positive) and apply the generalised Hooke's law to each direction.
  4. Add the three normal strains for volumetric strain; multiply by volume for ΔV.
  5. Check signs and magnitudes: lateral strain opposes axial strain, and volume change is small (a fraction of a per mille for steel at working stress).

Site notes

  • Strain gauge rosettes on bridges and buildings measure strains in several directions; the stresses are back-calculated with E and ν, so wrong constants give wrong stresses.
  • Confinement by spirals, hoops or steel tubes works because concrete expands sideways under compression (Poisson's effect, which grows near failure).
  • Elastomeric bearings are designed on G of the rubber; temperature and ageing change G, so bearings are inspected for excessive shear deformation.
  • In soils and rocks the same constants are used with drained or undrained values; saturated clay loaded quickly behaves with ν close to 0.5.
Common mistakes
  • Using ν with the wrong sign, so that lateral strain comes out positive under tension.
  • Forgetting the Poisson terms when two or three stresses act together, and adding only σ_x/E.
  • Using E = 2G(1 + ν) for timber or other anisotropic materials.
  • Expecting volume change of a stretched steel bar to be zero; it is zero only when ν = 0.5.
  • Mixing GPa and N/mm² in the same equation.
Quick check

For any isotropic material with ν between 0 and 0.5, G lies between E/3 and E/2; steel G ≈ 0.38 E (ν = 0.3), uncracked concrete G ≈ 0.42 E (ν = 0.2). A computed G outside this band signals an input error.

Summary

  • Four elastic constants E, G, K, ν; only two are independent for an isotropic material.
  • E = 2G(1 + ν); E = 3K(1 − 2ν); E = 9KG/(3K + G).
  • Generalised Hooke's law adds Poisson contractions from all normal stresses.
  • Volumetric strain = (1 − 2ν)(σ_x + σ_y + σ_z)/E; ν ≤ 0.5.

Practice questions

Tap a question to see the answer.

1Steel has E = 210 GPa and ν = 0.3. Find G.

G = 210 / 2.6 = 80.8 GPa.

2A material has K = 160 GPa and G = 80 GPa. Find E and ν.

E = 9 × 160 × 80 / (480 + 80) = 205.7 GPa; ν = (480 − 160)/(2 × 560) = 0.286.

3What does a Poisson's ratio of 0.5 mean physically?

The material does not change volume (incompressible); K becomes infinite. Rubber and saturated clay loaded quickly come close to this.

4A steel block (E = 200 GPa, ν = 0.3) has σ_x = 120 N/mm² (tension), σ_y = 80 N/mm² (compression) and σ_z = 0. Find the three strains and the change in volume of a 100 mm cube.

ε_x = (120 + 0.3 × 80)/200 000 = 7.2 × 10⁻⁴; ε_y = (−80 − 0.3 × 120)/200 000 = −5.8 × 10⁻⁴; ε_z = −0.3 × 40/200 000 = −0.6 × 10⁻⁴; e_v = 0.8 × 10⁻⁴; ΔV = 80 mm³ (increase).

5A 20 mm bar under tension has a longitudinal strain of 8.0 × 10⁻⁴ and its diameter decreases by 0.0048 mm. Find Poisson's ratio.

Lateral strain = 0.0048/20 = 2.4 × 10⁻⁴; ν = 2.4/8.0 = 0.30.

6A steel component (K = 166.7 GPa) is subjected to a uniform pressure of 50 N/mm². Find the volumetric strain and the volume change of 1 m³.

e_v = −50 / 166 700 = −3.0 × 10⁻⁴; ΔV = −3.0 × 10⁻⁴ m³ (0.3 litre decrease).

References

Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.

  • B. J. Goodno, J. M. Gere, Mechanics of Materials, Cengage Learning, 9th edition, 2018.
  • R. C. Hibbeler, Mechanics of Materials, Pearson, 10th edition, 2016.
  • F. P. Beer, E. R. Johnston, J. T. DeWolf, D. F. Mazurek, Mechanics of Materials, McGraw Hill, 8th edition, 2020.
  • E. P. Popov, Engineering Mechanics of Solids, Prentice Hall, 2nd edition, 1998.
Suggest a correction

If something on this page is wrong, tell the editor. Your message is sent privately and is not published.

Sent privately to the Indiacon editor; not published.