Indiacon CivilSubscribe

Textbook › Strength of Materials › Chapter 3 › Lesson 3.1

3.1 Theory of simple bending

Strength of Materials Chapter 3: Bending stresses Under review — not yet three-checked Author: Indiacon

Learning objectives

After this lesson you should be able to:

  • Explain what happens inside a beam in pure bending: fibres on one side shorten, fibres on the other side lengthen, and one surface, the neutral surface, keeps its length.
  • Derive the bending equation M/I = σ/y = E/R from geometry, Hooke's law and equilibrium, and show why the neutral axis passes through the centroid.
  • Find the moment of inertia of rectangular, circular and T-sections using the parallel axis theorem, and use it to work out bending stresses at any fibre.

Theory

Chapter 2 found how large the bending moment is at each section of a beam. This chapter asks what that moment does to the material. Bend a rubber eraser between your fingers and you can see the answer: the top face shortens and wrinkles, the bottom face stretches, and somewhere in between there is a layer that does not change length. That layer is the neutral surface, and its trace on a cross-section is the neutral axis. Fibres above it are in compression and fibres below it are in tension for a sagging moment.

The simplest case to study is pure bending, where a length of beam carries a constant moment and no shear, as between the two loads of a four-point bending test (lesson 2.4). Symmetry then forces every cross-section to stay plane and to turn about the neutral axis, so the beam bends into a circular arc of radius R. A fibre at distance y from the neutral surface has a strain proportional to y. With a linear elastic material, the stress is proportional to the strain, so bending stress grows linearly from zero at the neutral axis to its largest values at the top and bottom fibres.

shortens (compression)lengthens (tension)neutral surfaceMMto centre O, radius RsectionσcσtNAIndiacon original, not to scale
Figure 3.1: Pure bending: the beam curves to radius R, fibres above the neutral surface shorten and those below lengthen, and the bending stress varies linearly across the section, zero at the neutral axis. Indiacon original, not to scale.

Two equilibrium conditions fix the rest. There is no axial force on the section, so the tension below the neutral axis must balance the compression above it; this puts the neutral axis exactly through the centroid of the section. The internal stresses must also add up to the applied moment, and that sum brings in the second moment of area I of the section about the neutral axis. The result is the bending equation M/I = σ/y = E/R, which links the moment, the stress, the material stiffness and the curvature in one line.

The equation explains why beams are deep and why I-sections look the way they do. Stress is largest far from the neutral axis, so material placed there works hardest and adds most to I, which depends on the square of the distance. Material near the neutral axis carries little bending stress. Real beams also carry shear, but for ordinary span-to-depth ratios the shear barely changes the bending stresses, so the same equation is used for beams under any transverse load, with M taken from the bending moment diagram at the section being checked.

Derivation

  1. Take a beam segment in pure bending. Two cross-sections a distance dx apart, plane before bending, stay plane and rotate to meet at the centre of curvature O; the angle between them is dθ and the neutral surface bends to radius R, so dx = R dθ.
  2. A fibre at distance y from the neutral surface, measured away from the centre of curvature, now has length (R + y) dθ; its strain is ε = [(R + y) dθ − R dθ]/(R dθ) = y/R.
  3. Hooke's law, with the same E in tension and compression and no lateral restraint effects: σ = E ε = E y/R. Stress is linear in y.
  4. Axial equilibrium: ∫σ dA = (E/R) ∫y dA = 0, so ∫y dA = 0, the first moment of area about the neutral axis is zero, and the neutral axis passes through the centroid.
  5. Moment equilibrium: M = ∫σ y dA = (E/R) ∫y² dA = E I/R, where I = ∫y² dA is the second moment of area about the neutral axis.
  6. Combining σ/y = E/R and M = E I/R gives the bending equation M/I = σ/y = E/R.
  7. Section properties: rectangle b × d about its centroid I = b d³/12; solid circle of diameter d, I = π d⁴/64; for a composite shape, parallel axis theorem I = Σ(I_own + A h²), where h is the distance of each part's centroid from the neutral axis.
Formulas, symbols and SI units
  • M/I = σ/y = E/R
  • σ = M y/I (bending stress at distance y from the neutral axis, N/mm²)
  • ε = y/R (bending strain, dimensionless)
  • 1/R = M/(E I) (curvature, 1/mm)
  • Rectangle b × d: I = b d³/12 (mm⁴)
  • Solid circle, diameter d: I = π d⁴/64 (mm⁴)
  • Parallel axis theorem: I = I_G + A h² (mm⁴)
  • Centroid of a composite section: ȳ = Σ A_i y_i / Σ A_i (mm)
  • Units: M in N·mm (1 kN·m = 10⁶ N·mm), I in mm⁴, y in mm, σ and E in N/mm², R in mm
Assumptions and limits
  • The material is homogeneous, isotropic and linear elastic, with the same E in tension and in compression, and stresses stay below the limit of proportionality.
  • Plane sections remain plane and normal to the axis after bending (Bernoulli's assumption).
  • The beam is initially straight and of uniform section, and the radius of curvature is large compared with the depth.
  • The section has an axis of symmetry in the plane of loading, so bending occurs about one principal axis (unsymmetrical bending is lesson 3.4).
  • Each fibre is free to expand or contract sideways; layers do not press on each other.
  • Limits: the equation is not valid in deep beams (small span-to-depth ratio), near concentrated loads and supports, at sudden changes of section, in strongly curved members, or once the outer fibres yield or concrete cracks; those cases are treated separately.

Codes and standards

Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.

  • The theory of simple bending is mechanics and is not set by any design code; every structural code builds its elastic bending checks on it.
  • Steel design in IS 800:2007 works with the elastic and plastic section moduli that come from this theory; that use is described in lesson 3.2.
  • Side by side, not ranked: EN 1993-1-1 and AISC 360 use the same elastic theory for elastic section properties; RCC and timber design add material-specific rules on top of it.

Worked examples

Example 1 (exam style: rectangular beam)

Problem. A simply supported timber beam of span 4 m has a rectangular section 150 mm wide and 300 mm deep and carries a uniform load of 10 kN/m including its own weight. Find the maximum bending stress and the bending stress at a fibre 100 mm below the top face at mid-span.

  1. M_max = wL²/8 = 10 × 4²/8 = 20 kN·m = 20 × 10⁶ N·mm at mid-span.
  2. I = b d³/12 = 150 × 300³/12 = 3.375 × 10⁸ mm⁴; the neutral axis is at mid-depth, so y_max = 150 mm.
  3. σ_max = M y/I = 20 × 10⁶ × 150/3.375 × 10⁸ = 8.89 N/mm², compression at the top and tension at the bottom.
  4. The fibre 100 mm below the top is 50 mm above the neutral axis: σ = 20 × 10⁶ × 50/3.375 × 10⁸ = 2.96 N/mm² compression (one-third of the top-fibre value, because stress is linear in y).

Answer. σ_max = 8.89 N/mm²; at 100 mm below the top, 2.96 N/mm² compression

Example 2 (site style: bending a steel flat to a curve)

Problem. A steel flat 100 mm wide and 12 mm thick is to be bent cold to a curve for a handrail. Take E = 2 × 10⁵ N/mm² and a yield stress of 250 N/mm². What stress would a 3 m bending radius cause, what is the smallest radius at which the flat stays elastic and springs back fully, and what moment is needed to hold it at that radius?

  1. The flat bends about its 12 mm thickness, so y_max = 6 mm.
  2. At R = 3000 mm: σ = E y/R = 2 × 10⁵ × 6/3000 = 400 N/mm², above the yield stress, so the outer fibres yield and the flat takes a permanent set.
  3. Smallest elastic radius: R = E y/f_y = 2 × 10⁵ × 6/250 = 4800 mm = 4.8 m.
  4. I = b t³/12 = 100 × 12³/12 = 14 400 mm⁴.
  5. M = E I/R = 2 × 10⁵ × 14 400/4800 = 6.0 × 10⁵ N·mm = 0.6 kN·m. Check: σ = M y/I = 6 × 10⁵ × 6/14 400 = 250 N/mm².

Answer. 400 N/mm² at R = 3 m (yields); R_min elastic = 4.8 m; M = 0.6 kN·m

Example 3 (exam style: T-section)

Problem. A T-section has a flange 150 mm × 20 mm and a web 20 mm thick, overall depth 200 mm. It carries a sagging moment of 10 kN·m. Locate the neutral axis, find I about it, and find the largest compressive and tensile bending stresses.

  1. Flange area 150 × 20 = 3000 mm², centroid 190 mm above the bottom; web 20 × 180 = 3600 mm², centroid 90 mm above the bottom.
  2. ȳ = (3000 × 190 + 3600 × 90)/6600 = 135.45 mm above the bottom, so the neutral axis is 64.55 mm below the top.
  3. Flange: 150 × 20³/12 + 3000 × (190 − 135.45)² = 1.0 × 10⁵ + 8.926 × 10⁶ mm⁴.
  4. Web: 20 × 180³/12 + 3600 × (135.45 − 90)² = 9.72 × 10⁶ + 7.438 × 10⁶ mm⁴.
  5. I = 2.618 × 10⁷ mm⁴.
  6. Top fibre (compression): σ = 10 × 10⁶ × 64.55/2.618 × 10⁷ = 24.65 N/mm². Bottom fibre (tension): σ = 10 × 10⁶ × 135.45/2.618 × 10⁷ = 51.73 N/mm².

Answer. Neutral axis 135.45 mm above the bottom; I = 2.618 × 10⁷ mm⁴; 24.65 N/mm² compression at the top, 51.73 N/mm² tension at the bottom

Step-by-step procedure

  1. Find the bending moment M at the section to be checked from the bending moment diagram (chapter 2), with its sign.
  2. Locate the centroid of the cross-section; the neutral axis passes through it.
  3. Find I about the neutral axis, using the parallel axis theorem for built-up shapes.
  4. Find y to each fibre of interest, especially the extreme top and bottom fibres.
  5. Compute σ = M y/I and mark tension or compression from the sign of M (sagging: compression on top).
  6. Compare with the permissible or design stress for the material, and check that the assumptions of simple bending hold for the member.

Site notes

  • When a beam is lifted or stacked on two timber packers, its own weight bends it; long precast and steel members are lifted at marked points so that this bending stress stays small.
  • Cold bending of steel flats, pipes and rebars to a radius smaller than E y/f_y leaves a permanent set; that is fine for shaping, but it uses up some ductility, so tight bends must follow the approved bending radius.
  • Notches, holes and welded attachments on the tension flange of a beam sit where the bending stress is highest; check before cutting or welding on the bottom flange of a loaded steel beam.
  • Strain gauges fixed at the top and bottom of a beam during a load test should read equal and opposite strains for a symmetric section; unequal readings point to a shifted neutral axis, composite action or a cracked section.
Common mistakes
  • Taking y from the top or bottom face instead of from the neutral axis.
  • Putting the neutral axis at mid-depth of a T- or channel section instead of at its centroid.
  • Mixing units: M in kN·m with I in mm⁴, giving stresses that are wrong by 10⁶.
  • Forgetting the A h² term when finding I of a built-up section.
  • Checking only the larger y for an unsymmetrical section without checking which fibre is in tension and which material limit applies there.
Quick check

For a rectangular section, σ_max = 6M/(b d²). If a hand result for a rectangle of similar size differs from this by more than rounding, I or y has been taken about the wrong axis. Valid for linear elastic, symmetric sections only.

Summary

  • Bending strain and stress vary linearly with distance from the neutral axis: ε = y/R and σ = E y/R.
  • With no axial force, the neutral axis passes through the centroid.
  • M/I = σ/y = E/R links moment, stress, stiffness and curvature.
  • Material far from the neutral axis carries most of the bending; I grows with the square of that distance.
  • The equation holds for slender, linear elastic beams with plane sections; deep beams, cracked concrete and yielded steel need other methods.

Practice questions

Tap a question to see the answer.

1A rectangular beam 200 mm wide and 400 mm deep carries a bending moment of 40 kN·m. Find the maximum bending stress.

I = 200 × 400³/12 = 1.067 × 10⁹ mm⁴; σ = 40 × 10⁶ × 200/1.067 × 10⁹ = 7.5 N/mm² (also 6M/bd² = 7.5 N/mm²).

2A steel wire of 4 mm diameter is wound on a drum so that the radius of the wire axis is 1 m. Take E = 2 × 10⁵ N/mm². Find the maximum bending stress in the wire.

σ = E y/R = 2 × 10⁵ × 2/1000 = 400 N/mm².

3Why must the neutral axis pass through the centroid of the section in simple bending?

Because there is no axial force: ∫σ dA = (E/R)∫y dA = 0, so the first moment of area about the neutral axis is zero, which defines the centroidal axis.

4A solid circular steel bar of 100 mm diameter carries a bending moment of 5 kN·m. Find the maximum bending stress.

I = π × 100⁴/64 = 4.909 × 10⁶ mm⁴; σ = 5 × 10⁶ × 50/4.909 × 10⁶ = 50.9 N/mm².

5In a steel beam the bending stress at the extreme fibre, 150 mm from the neutral axis, is 120 N/mm². Find the stress at 90 mm from the neutral axis and the radius of curvature (E = 2 × 10⁵ N/mm²).

Stress is linear in y: 120 × 90/150 = 72 N/mm². R = E y/σ = 2 × 10⁵ × 150/120 = 2.5 × 10⁵ mm = 250 m.

6Can the bending equation be used for a transfer girder 3 m deep spanning 5 m? Give a reason.

Not directly. With a span-to-depth ratio below about 2, plane sections do not remain plane and the stress distribution is far from linear, so deep-beam methods (such as strut-and-tie) are used instead.

References

Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.

  • B. J. Goodno, J. M. Gere, Mechanics of Materials, Cengage Learning, 9th edition, 2018.
  • R. C. Hibbeler, Mechanics of Materials, Pearson, 10th edition, 2016.
  • F. P. Beer, E. R. Johnston, J. T. DeWolf, D. F. Mazurek, Mechanics of Materials, McGraw Hill, 8th edition, 2020.
  • E. P. Popov, Engineering Mechanics of Solids, Prentice Hall, 2nd edition, 1998.
Suggest a correction

If something on this page is wrong, tell the editor. Your message is sent privately and is not published.

Sent privately to the Indiacon editor; not published.