3.2 Bond and development length
After this lesson you should be able to:
- Explain how force passes between steel and concrete by bond (adhesion, friction and the bearing of ribs) and why bars need a development length on each side of any section where they are highly stressed.
- Derive Ld = φ σs/(4 τbd) from equilibrium of an embedded bar and use the design bond stresses of IS 456:2000 cl. 26.2.1.1 for plain and deformed bars in tension and compression.
- Check anchorage at simple supports and points of inflection by cl. 26.2.3.3 (c), use the anchorage values of bends and hooks, and compute lap lengths by cl. 26.2.5.1.
Theory
Reinforced concrete works only because the steel and concrete strain together. Lesson 2.1 assumed perfect bond: the strain in a bar equals the strain in the concrete beside it. That assumption holds only if a force can pass from the concrete into the bar along its surface. The force per unit area of bar surface is the bond stress. In plain round bars it comes from chemical adhesion and friction; in deformed (ribbed) bars it comes mainly from the ribs bearing against the concrete, like the threads of a screw, which is why deformed bars bond much better.
A bar that must carry a force T = σs As at a section can only pick up that force gradually along its length. If the average bond stress is τbd and the bar diameter φ, a length L of bar collects π φ L τbd. The length needed to develop the full design stress is therefore the development length Ld. The code rule is simple: the calculated tension or compression in any bar at any section shall be developed on each side of that section by an appropriate development length, end anchorage or both (cl. 26.2). This is why bars are carried past the points where they are needed, into supports and beyond points of inflection.
Bond failure takes two forms. In plain bars the bar simply pulls out. In deformed bars the ribs push outwards on the concrete and, if the cover or the spacing is small, the cover splits along the bar before the bar can be pulled out. Larger cover, confinement by stirrups and well-compacted concrete all improve bond. Bars at the top of a deep pour bond less well because bleed water and air collect beneath them; that is one reason the lap rules of IS 456 add a factor for top bars with small cover.
Where there is not enough straight length, the bar is bent or hooked. A bend or hook does not create extra strength by itself, but it provides an anchorage value that counts towards Ld. IS 456:2000 cl. 26.2.2.1 counts a bend as 4 bar diameters for each 45 degrees of bend, up to 16 diameters, and a standard U-type hook as 16 diameters. At simple supports and points of inflection, where the moment is small but the shear is large, the code adds a separate check (cl. 26.2.3.3 (c)) that limits the bar diameter so that the bar can develop its stress within the short distance available.
Derivation
- Consider a straight bar of diameter φ embedded over a length Ld and pulled with a stress σs. The pull is σs × π φ²/4.
- Bond resists it over the surface: average bond stress τbd times the area π φ Ld.
- Equilibrium: π φ Ld τbd = σs π φ²/4, so Ld = φ σs/(4 τbd) (cl. 26.2.1). At the limit state σs = 0.87 fy.
- Design bond stress (cl. 26.2.1.1): for plain bars in tension τbd = 1.2, 1.4, 1.5, 1.7 and 1.9 N/mm² for M20, M25, M30, M35 and M40 and above; for deformed bars to IS 1786 these increase by 60 per cent, and for bars in compression by a further 25 per cent.
- So for Fe 415 deformed bars in M20: Ld = φ × 0.87 × 415/(4 × 1.2 × 1.6) = 47.0 φ in tension and 37.6 φ in compression; for Fe 500 in M25: 48.5 φ and 38.8 φ.
- Check at simple supports and points of inflection (cl. 26.2.3.3 (c)): Ld computed for fd = 0.87 fy must not exceed M1/V + L0, where M1 is the moment of resistance of the section with all its bars stressed to fd, V the shear at the section and L0 the anchorage beyond the centre of the support (or, at a point of inflection, the larger of d and 12 φ). M1/V may be increased by 30 per cent where the bar ends are confined by a compressive reaction, as at a simple support resting on a wall.
Development length: Ld = φ σs/(4 τbd) (mm; φ in mm, σs and τbd in N/mm²), with σs = 0.87 fy at the limit stateDeformed bars in tension: τbd = 1.6 × (plain-bar value); in compression: τbd = 1.25 × 1.6 × (plain-bar value) (N/mm²)Anchorage value of bends: 4 φ for each 45 degrees, at most 16 φ; standard U-type hook 16 φ (mm)Anchorage at simple supports: Ld ≤ 1.3 M1/V + L0 where the end is confined by a compressive reaction, otherwise Ld ≤ M1/V + L0 (mm; M1 in N mm, V in N)Lap length in flexural tension: the greater of Ld and 30 φ; in direct tension the greater of 2 Ld and 30 φ; straight length at least 15 φ or 200 mm (mm)Bundled bars: Ld of each bar increased by 10, 20 and 33 per cent for two, three and four bars in contact (dimensionless factors)
- Bond stress is taken as uniform along the development length; in reality it peaks near cracks and loaded ends, and the uniform value is a design average.
- The bar is surrounded by adequate cover and spacing, so the bond is not cut short by splitting; the cover rules of cl. 26.4 and the spacing rules of cl. 26.3 are assumed to be met.
- Deformed bars conform to IS 1786; the 60 per cent increase does not apply to plain bars.
- The anchorage values of bends and hooks assume bends formed to the standard dimensions; bearing stresses inside non-standard bends are checked separately (cl. 26.2.2.5).
- Limits: the expressions do not cover bars under repeated or seismic cyclic loading, where special anchorage and lap rules apply, nor epoxy-coated or very large bars beyond the scope of the clause; lap splices shall not be used for bars larger than 32 mm, which must be welded or mechanically spliced (cl. 26.2.5.1(a) as substituted by Amendment No. 3, 2007; the original 2000 wording said 36 mm).
Codes and standards
Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.
- IS 456:2000 cl. 26.2 (stress in any bar to be developed on each side of the section), cl. 26.2.1 (Ld = φ σs/(4 τbd)), cl. 26.2.1.1 (design bond stress for plain bars in tension 1.2, 1.4, 1.5, 1.7 and 1.9 N/mm² for M20, M25, M30, M35 and M40 and above; plus 60 per cent for deformed bars to IS 1786; plus 25 per cent in compression), cl. 26.2.1.2 (bundled bars: 10, 20 and 33 per cent).
- IS 456:2000 cl. 26.2.2.1 (anchorage of bars in tension: bends 4 φ per 45 degrees up to 16 φ, U-type hook 16 φ), cl. 26.2.2.2 (bars in compression), cl. 26.2.2.4 (anchorage of stirrups: 90-degree bend plus 8 φ, 135-degree bend plus 6 φ, or 180-degree bend plus 4 φ), cl. 26.2.3.3 (c) (Ld ≤ M1/V + L0 at simple supports and points of inflection, M1/V increased by 30 per cent where confined by a compressive reaction), cl. 26.2.5.1 (lap lengths: Ld or 30 φ in flexural tension, 2 Ld or 30 φ in direct tension, straight length at least 15 φ or 200 mm, factor 1.4 for top bars with cover less than twice the bar diameter, no laps for bars over 36 mm).
- Indian, European and American practice are listed side by side and not ranked: the European concrete code (EN 1992-1-1) builds the anchorage length from an ultimate bond stress that depends on concrete strength and bond conditions, then multiplies it by factors for bar shape, cover, confinement and transverse pressure; the American code (ACI 318) gives development lengths from expressions that include factors for bar position, coating, bar size and confinement. The factors differ and are not reproduced here.
Worked examples
Problem. Find the development length of a 20 mm Fe 415 deformed bar in M20 concrete in tension and in compression, and express both as multiples of the bar diameter.
- Plain-bar design bond stress for M20 is 1.2 N/mm²; deformed bar in tension 1.2 × 1.6 = 1.92 N/mm²; in compression 1.92 × 1.25 = 2.40 N/mm².
- Tension: Ld = 20 × 0.87 × 415/(4 × 1.92) = 940 mm, that is 47.0 φ.
- Compression: Ld = 20 × 0.87 × 415/(4 × 2.40) = 752 mm, that is 37.6 φ.
- Check by equilibrium: a 20 mm bar at 0.87 × 415 = 361 N/mm² carries 113.4 kN; over 940 mm its surface is π × 20 × 940 = 59 060 mm², so the average bond stress is 113 400/59 060 = 1.92 N/mm², as assumed.
Answer. Ld = 940 mm (47 φ) in tension and 752 mm (37.6 φ) in compression
Problem. A simply supported beam 230 mm wide with d = 410 mm, M20 concrete and Fe 415 steel has two 16 mm bars continuing into a 300 mm wide masonry support. The factored shear at the support is 100 kN. The bars run 110 mm beyond the centre of the support (end cover 40 mm) and then turn up through 90 degrees. Check cl. 26.2.3.3 (c).
- Ld for 16 mm bars = 16 × 47.0 = 752 mm.
- M1 with both bars at 0.87 fy: xu = 0.87 × 415 × 402.1/(0.36 × 20 × 230) = 87.7 mm; M1 = 0.87 × 415 × 402.1 × (410 − 0.42 × 87.7) = 54.2 kN m.
- L0 = straight length beyond the centre 110 mm + anchorage value of a 90-degree bend 8 φ = 128 mm, total 238 mm.
- The beam bears on the wall, so the bar ends are confined by the reaction: 1.3 M1/V + L0 = 1.3 × 54.2 × 10⁶/100 000 + 238 = 942 mm ≥ 752 mm. The 16 mm bars are acceptable.
- Without the confinement bonus M1/V + L0 = 780 mm, still above 752 mm. The check bites for larger bars and higher shear: with two 20 mm bars (M1 = 80.0 kN m, L0 = 110 + 160 = 270 mm) at V = 150 kN, M1/V + L0 = 803 mm is less than Ld = 940 mm, so such bars would be acceptable only where the confinement bonus applies (1.3 M1/V + L0 = 963 mm).
Answer. 1.3 M1/V + L0 = 942 mm ≥ Ld = 752 mm: anchorage adequate
Problem. Top bars of 25 mm diameter, Fe 500, in an M25 beam must be lapped near midspan where they are in flexural tension under a reversal case. The clear cover to the bars is 40 mm. Find the lap length and the stagger needed if half the bars are lapped at one section.
- Deformed bar in tension, M25: τbd = 1.4 × 1.6 = 2.24 N/mm²; Ld = 25 × 0.87 × 500/(4 × 2.24) = 1 214 mm (48.5 φ); 30 φ = 750 mm, so the basic lap is 1 214 mm.
- The bars are at the top of the section as cast and the cover 40 mm is less than 2 φ = 50 mm, so the lap is increased by the factor 1.4 (cl. 26.2.5.1 (c)): 1.4 × 1 214 = 1 699 mm, say 1 700 mm.
- Laps count as staggered when their centres are at least 1.3 times the lap length apart: 1.3 × 1 699 = 2 209 mm, say 2 210 mm between lap centres.
- Keep laps away from sections where the moment exceeds half the moment of resistance and do not lap more than half the bars at one section, as cl. 26.2.5 recommends.
Answer. Lap 1 700 mm (1.4 × Ld); stagger lap centres by at least about 2 210 mm
Step-by-step procedure
- Identify the critical sections where each bar is fully stressed (maximum moment, column faces, cut-off points).
- Compute Ld = φ × 0.87 fy/(4 τbd) with τbd for the grade, bar type and tension or compression.
- Provide Ld on each side of every critical section by straight length, bends or hooks (cl. 26.2.2.1 anchorage values).
- At simple supports and points of inflection check Ld ≤ 1.3 M1/V + L0 (or M1/V + L0 if unconfined); if it fails, use smaller bars or more anchorage.
- Detail laps away from high-moment zones with the lengths and factors of cl. 26.2.5.1, staggered where possible.
- Show Ld, laps and hook lengths on the bar bending schedule so that site teams cut and fix the right lengths.
Site notes
- Laps and anchorages are often shortened to save steel or to fit into formwork; check the lengths on site against the bar bending schedule.
- Deformed bars must be clean of loose rust, oil, mud and form-release agent, which all reduce bond; tight mill scale and light rust are not harmful.
- Compaction around bar ends and laps matters: honeycombing at a lap destroys bond exactly where the force transfers.
- Hooks and bends must be formed cold to the standard dimensions; heating bars to bend them alters the steel.
- Top bars in deep pours bond less well; follow the top-bar factor and keep the specified cover.
- Using the plain-bar bond stress for deformed bars, or adding the 60 per cent twice.
- Measuring development length from the support face when the critical section is elsewhere, or ignoring the need for Ld on both sides of a section.
- Forgetting the cl. 26.2.3.3 (c) check at simple supports, where large bars may not develop their stress within the short length available.
- Adopting a lap shorter than 30 φ in flexural tension because Ld came out smaller.
- Lapping all bars at one section, at the point of maximum moment.
For deformed bars at 0.87 fy, tension Ld/φ is 47 φ (Fe 415, M20), 40 φ (M25), 38 φ (M30), 33 φ (M35) and 30 φ (M40 and above); for Fe 500 the same grades give 57 φ, 48.5 φ, 45 φ, 40 φ and 36 φ. In compression multiply by 0.8. A 90-degree bend adds 8 φ and a U-hook 16 φ of anchorage. Query a tension length shorter than the value for the actual grade; a single 40 φ check is unconservative for Fe 500 in M20–M30.
Summary
- Bond transfers force between steel and concrete; deformed bars bond mainly by rib bearing and are much more effective than plain bars.
- Equilibrium of an embedded bar gives Ld = φ σs/(4 τbd), with σs = 0.87 fy at the limit state.
- Design bond stresses for plain bars in tension are 1.2 to 1.9 N/mm² for M20 to M40, increased by 60 per cent for deformed bars and by a further 25 per cent in compression.
- Bends add 4 φ per 45 degrees (up to 16 φ) and U-hooks 16 φ of anchorage; at simple supports and points of inflection Ld must not exceed 1.3 M1/V + L0 (or M1/V + L0 when unconfined).
- Laps in flexural tension are the greater of Ld and 30 φ, increased by 1.4 for top bars with small cover, and should be staggered away from high-moment sections.
Practice questions
Tap a question to see the answer.
1Find Ld in tension for a 12 mm Fe 500 deformed bar in M30 concrete.
τbd = 1.5 × 1.6 = 2.4 N/mm²; Ld = 12 × 435/(4 × 2.4) = 544 mm (45.3 φ).
2Find Ld in tension for a 16 mm Fe 415 deformed bar in M25 concrete.
τbd = 2.24 N/mm²; Ld = 16 × 361.05/(4 × 2.24) = 645 mm (40.3 φ).
3What is the anchorage value of a 135-degree bend on a 16 mm main bar?
Three 45-degree steps: 3 × 4 × 16 = 192 mm (below the 16 φ = 256 mm cap).
4Three 20 mm Fe 415 bars are bundled in contact in M20 concrete. Find Ld of each bar.
1.2 × 940 = 1 128 mm.
5Find the lap length of 16 mm Fe 415 bars in direct tension in M20 concrete.
Greater of 2 Ld = 2 × 752 = 1 504 mm and 30 φ = 480 mm: 1 504 mm.
6Why must Ld be provided on both sides of a critical section?
The full bar force exists at the section, and bond can only build it up gradually, so the bar needs Ld of embedment in each direction to develop that force without slipping.
References
Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.
- S. U. Pillai, D. Menon, Reinforced Concrete Design, Tata McGraw Hill (now McGraw Hill Education (India)), 3rd edition, 2009.
- P. C. Varghese, Limit State Design of Reinforced Concrete, Prentice Hall of India (PHI Learning), 2nd edition, 2008.
- J. K. Wight, J. G. MacGregor, Reinforced Concrete: Mechanics and Design, Pearson, 6th edition, 2012.
- R. Park, T. Paulay, Reinforced Concrete Structures, John Wiley and Sons, 1975.