7.2 Principal stresses and maximum shear stress
After this lesson you should be able to:
- Find the principal stresses and principal planes at a point in plane stress, both from the transformation equations and as eigenvalues of the stress matrix.
- Find the maximum in-plane shear stress and its planes, and the absolute maximum shear stress when the third principal stress is zero.
- Apply principal stresses to diagonal tension in concrete beams, girder webs and pressure pipes.
Theory
As the plane through a point turns, the normal stress σ_θ rises and falls. Its greatest and least values are the principal stresses σ₁ and σ₂, and the planes on which they act are the principal planes. Setting dσ_θ/dθ = 0 gives tan 2θ_p = 2τ_xy/(σ_x − σ_y). That equation has two solutions 90° apart, one for σ₁ and one for σ₂. Remarkably, the condition dσ_θ/dθ = 0 is exactly the condition τ_θ = 0, so the principal planes carry no shear stress at all.
Substituting θ_p back gives σ₁,₂ = (σ_x + σ_y)/2 ± √[((σ_x − σ_y)/2)² + τ_xy²]. The square root is called R; it is the radius of Mohr's circle in the next lesson. The same results follow by treating the stresses as a 2 × 2 symmetric matrix [[σ_x, τ_xy], [τ_xy, σ_y]]: its eigenvalues are the principal stresses and its eigenvectors are the principal directions. This view generalises to three dimensions and is how analysis software finds principal stresses.
The shear stress τ_θ is largest on planes at 45° to the principal planes. The maximum in-plane shear stress equals R = (σ₁ − σ₂)/2, and the normal stress on those planes is the average (σ_x + σ_y)/2, not zero. In plane stress the third principal stress, perpendicular to the plate, is σ₃ = 0. If σ₁ and σ₂ have the same sign, the largest shear stress in the material acts on a plane tilted out of the plate, with value half the largest principal stress. The absolute maximum shear stress is therefore half the difference between the largest and smallest of σ₁, σ₂ and 0.
Principal stresses explain several familiar civil patterns. In a beam near a support, bending stress and shear stress combine into an inclined principal tension, so concrete cracks diagonally, and the shear reinforcement crosses those cracks. In a prestressed beam the longitudinal compression turns the principal tension much smaller, which is one reason prestressed girders can have thin webs. In pipes and tanks, the hoop and longitudinal stresses are the principal stresses when no shear acts, and any twist or bending adds shear that rotates them.
Derivation
- Differentiate σ_θ: dσ_θ/dθ = −(σ_x − σ_y) sin 2θ + 2τ_xy cos 2θ = 0, so tan 2θ_p = 2τ_xy/(σ_x − σ_y).
- Compare with τ_θ = −(σ_x − σ_y)/2 × sin 2θ + τ_xy cos 2θ: dσ_θ/dθ = 2τ_θ, so τ = 0 on the principal planes.
- At 2θ_p: cos 2θ_p = ((σ_x − σ_y)/2)/R and sin 2θ_p = τ_xy/R with R = √[((σ_x − σ_y)/2)² + τ_xy²], giving σ₁ = (σ_x + σ_y)/2 + R. The other root (2θ_p + 180°) gives σ₂ = (σ_x + σ_y)/2 − R.
- Eigenvalue form: det([[σ_x − λ, τ_xy], [τ_xy, σ_y − λ]]) = 0 gives λ² − (σ_x + σ_y) λ + (σ_x σ_y − τ_xy²) = 0, whose roots are σ₁ and σ₂. Hence σ₁ + σ₂ = σ_x + σ_y and σ₁ σ₂ = σ_x σ_y − τ_xy².
- Maximum shear: dτ_θ/dθ = 0 gives tan 2θ_s = −(σ_x − σ_y)/(2τ_xy) = −1/tan 2θ_p, so 2θ_s = 2θ_p ± 90°, θ_s = θ_p ± 45°, and τ_max = R = (σ₁ − σ₂)/2.
- On the planes of maximum shear, σ = (σ_x + σ_y)/2.
- Absolute maximum shear with σ₃ = 0: τ_abs = (σ_max − σ_min)/2 taken over σ₁, σ₂ and 0.
σ₁,₂ = (σ_x + σ_y)/2 ± R, R = √[((σ_x − σ_y)/2)² + τ_xy²] (N/mm²)tan 2θ_p = 2τ_xy/(σ_x − σ_y); the direction of σ₁ is 2θ₁ = atan2(2τ_xy, σ_x − σ_y)Principal planes carry zero shear stressτ_max (in-plane) = R = (σ₁ − σ₂)/2 on planes at 45° to the principal planes, with σ = (σ_x + σ_y)/2 on themInvariants: σ₁ + σ₂ = σ_x + σ_y; σ₁ σ₂ = σ_x σ_y − τ_xy²Absolute maximum shear (σ₃ = 0): τ_abs = ½ × (largest − smallest of σ₁, σ₂, 0)
- Plane stress with σ₃ = 0 normal to the plate; for a full three-dimensional state the 3 × 3 matrix is used in the same way.
- The stress components at the point are known, from analysis or measurement.
- Equilibrium only; the results hold for any material.
- Signs follow lesson 7.1: tension positive, τ_xy positive in +y on the +x face, θ anticlockwise from x to the plane normal.
- Limits: whether a material fails at given principal stresses is the subject of the theories of failure in lesson 7.5.
Codes and standards
Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.
- Principal stresses are mechanics; no design code governs the derivation or the formulas of this lesson.
- Codes use principal stresses indirectly: reinforced concrete shear design rules are calibrated on the diagonal tension that principal stresses describe, and steel plate checks combine normal and shear stress through an equivalent stress based on the theories of lesson 7.5; each code sets its own strengths and factors.
- Side by side, not ranked: the Indian, European (EN 1992-1-1, EN 1993-1-1) and American (ACI 318, AISC 360) codes all start from the same principal stress state described here.
Worked examples
Problem. At a point in a girder web, σ_x = 80 N/mm² (bending), σ_y = 0 and τ_xy = 60 N/mm². Find the principal stresses, the principal directions and the maximum in-plane shear stress.
- Average = 40 N/mm²; R = √(40² + 60²) = √5200 = 72.11 N/mm².
- σ₁ = 40 + 72.11 = 112.11 N/mm²; σ₂ = 40 − 72.11 = −32.11 N/mm².
- tan 2θ_p = 2 × 60/80 = 1.5, 2θ_p = 56.31°, so σ₁ acts on the plane at θ₁ = 28.15° and σ₂ at 118.15°.
- τ_max = R = 72.11 N/mm² on planes at 28.15° ± 45°, with normal stress 40 N/mm².
- Check: σ₁ + σ₂ = 80 = σ_x + σ_y; σ₁ σ₂ = −3600 = 0 − 60².
Answer. σ₁ = 112.1 N/mm² at 28.2°, σ₂ = −32.1 N/mm²; τ_max = 72.1 N/mm²
Problem. At the centroid of a prestressed concrete girder web near a support, the prestress gives σ_x = −5.0 N/mm² (compression) and the shear stress is τ_xy = 1.8 N/mm², with σ_y = 0. Find the principal tension and compare it with the case without prestress.
- Average = −2.5 N/mm²; R = √(2.5² + 1.8²) = √9.49 = 3.081 N/mm².
- σ₁ = −2.5 + 3.081 = 0.58 N/mm² (tension); σ₂ = −2.5 − 3.081 = −5.58 N/mm².
- Direction of σ₁: 2θ₁ = atan2(3.6, −5.0) = 144.25°, θ₁ = 72.1° from the girder axis.
- Without prestress (σ_x = 0) the point is in pure shear: σ₁ = τ_xy = 1.8 N/mm² at 45°.
- The prestress cuts the principal tension from 1.80 to 0.58 N/mm² and steepens it, so diagonal cracking is far less likely.
Answer. σ₁ = 0.58 N/mm² at 72.1°, σ₂ = −5.58 N/mm²; without prestress σ₁ = 1.80 N/mm²
Problem. On the outer surface of a steel penstock, the longitudinal stress is σ_x = 60 N/mm², the hoop stress σ_y = 120 N/mm² and a shear stress τ_xy = 20 N/mm² arises from twist at a bend. The radial stress on the outer surface is zero. Find the principal stresses, the maximum in-plane shear and the absolute maximum shear.
- Average = 90 N/mm²; R = √(30² + 20²) = √1300 = 36.06 N/mm².
- σ₁ = 126.06 N/mm², σ₂ = 53.94 N/mm², σ₃ = 0 (radial).
- In-plane τ_max = R = 36.06 N/mm².
- Both in-plane principal stresses are tensile, so the absolute maximum shear is (126.06 − 0)/2 = 63.03 N/mm², on planes tilted through the wall thickness.
- Using only the in-plane value would understate the largest shear by about 43 %.
Answer. σ₁ = 126.1, σ₂ = 53.9, σ₃ = 0 N/mm²; in-plane τ_max = 36.1, absolute τ_max = 63.0 N/mm²
Step-by-step procedure
- Write σ_x, σ_y and τ_xy with signs from analysis or measurement.
- Compute the average and R; then σ₁ = average + R and σ₂ = average − R.
- Find the direction of σ₁ from 2θ₁ = atan2(2τ_xy, σ_x − σ_y), or by checking σ_θ at one root of tan 2θ_p.
- Find τ_max = R in the plane, and with σ₃ = 0 the absolute maximum shear.
- Check σ₁ + σ₂ = σ_x + σ_y and σ₁ σ₂ = σ_x σ_y − τ_xy², and sketch the principal element.
Site notes
- Diagonal cracks near beam supports run roughly at right angles to the principal tension; the stirrups and bent bars that cross them are placed for this reason.
- Cracks in girder webs, deep beams and corbels are read on site against the expected principal tension directions to judge whether they are structural or only shrinkage.
- Prestressed girders keep principal tension low in the web, so cracks in a prestressed web near a support deserve prompt investigation.
- Analysis software plots principal stress vectors on plates and walls; check the arrows' directions against hand calculations at one or two points.
- Taking the root of tan 2θ_p without checking which principal stress it belongs to.
- Assuming the maximum shear planes carry no normal stress; they carry the average stress.
- Ignoring σ₃ = 0 and reporting only the in-plane maximum shear when σ₁ and σ₂ have the same sign.
- Dropping the sign of τ_xy, which flips the principal directions.
- Confusing the angle to the plane with the angle to the stress direction; for principal stresses the two coincide only because the plane's normal is the stress direction.
Principal stresses are the eigenvalues of [[σ_x, τ_xy], [τ_xy, σ_y]]; their sum equals σ_x + σ_y and their product σ_x σ_y − τ_xy², which checks any answer in seconds.
Summary
- Principal stresses are the extreme normal stresses at a point, on planes with no shear.
- σ₁,₂ = (σ_x + σ_y)/2 ± R, with R = √[((σ_x − σ_y)/2)² + τ_xy²].
- They are the eigenvalues of the stress matrix; the eigenvectors give their directions.
- τ_max in the plane is R at 45° to the principal planes, with the average normal stress on those planes.
- With σ₃ = 0 the absolute maximum shear may exceed R when σ₁ and σ₂ share a sign.
Practice questions
Tap a question to see the answer.
1σ_x = 50, σ_y = −30, τ_xy = 30 N/mm². Find σ₁, σ₂, τ_max and θ₁.
Average 10, R = √(40² + 30²) = 50; σ₁ = 60, σ₂ = −40 N/mm²; τ_max = 50 N/mm²; tan 2θ = 60/80, θ₁ = 18.43°.
2A point is in pure shear, τ_xy = 40 N/mm². Find the principal stresses and their planes.
σ₁ = +40 N/mm² on the plane at 45°, σ₂ = −40 N/mm² on the plane at 135°.
3σ_x = 100, σ_y = 40 N/mm², τ_xy = 0, σ₃ = 0. Find the in-plane and absolute maximum shear stresses.
In-plane τ_max = (100 − 40)/2 = 30 N/mm²; absolute τ_max = (100 − 0)/2 = 50 N/mm².
4For σ_x = 50, σ_y = −30, τ_xy = 30 N/mm², check the two invariants against the principal stresses of Q1.
σ₁ + σ₂ = 60 − 40 = 20 = 50 − 30; σ₁ σ₂ = −2400 = 50 × (−30) − 30².
5At a point near the top of a beam, σ_x = −90 N/mm², σ_y = 0 and τ_xy = 30 N/mm². Find the principal stresses.
Average −45, R = √(45² + 30²) = 54.08; σ₁ = 9.08 N/mm², σ₂ = −99.08 N/mm².
6A shaft surface carries σ = 60 N/mm² from bending and τ = 40 N/mm² from torsion. Find σ₁, σ₂ and τ_max.
Average 30, R = √(30² + 40²) = 50; σ₁ = 80, σ₂ = −20 N/mm²; τ_max = 50 N/mm².
References
Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.
- B. J. Goodno, J. M. Gere, Mechanics of Materials, Cengage Learning, 9th edition, 2018.
- R. C. Hibbeler, Mechanics of Materials, Pearson, 10th edition, 2016.
- F. P. Beer, E. R. Johnston, J. T. DeWolf, D. F. Mazurek, Mechanics of Materials, McGraw Hill, 8th edition, 2020.
- E. P. Popov, Engineering Mechanics of Solids, Prentice Hall, 2nd edition, 1998.