7.4 Strain transformation and strain rosettes
After this lesson you should be able to:
- Derive the transformation equations for plane strain and find principal strains and the maximum shear strain.
- Reduce the readings of rectangular (0°, 45°, 90°) and delta (0°, 60°, 120°) strain-gauge rosettes to ε_x, ε_y and γ_xy, and then to principal strains.
- Convert measured principal strains to principal stresses with Hooke's law for plane stress, as done in load tests and monitoring of bridges and buildings.
Theory
Stress cannot be measured directly; strain can. A bonded electrical strain gauge measures the normal strain along one line only, so engineers who need the full state of strain at a point on a girder, a pipe or a concrete surface fix three gauges in different directions at the same spot. This group is a strain rosette. To use it we need the rule that relates the normal strain in any direction to the strain components ε_x, ε_y and γ_xy, which is the strain transformation.
The geometry of a small element shows that the normal strain along a line at angle θ to the x-axis is ε_θ = ε_x cos² θ + ε_y sin² θ + γ_xy sin θ cos θ, where γ_xy is the engineering shear strain, the decrease in the right angle between the x and y directions. Written with double angles, this has exactly the same form as the stress equation of lesson 7.1, with σ replaced by ε and τ_xy replaced by γ_xy/2. Every stress result therefore has a strain twin: principal strains, a maximum shear strain and a Mohr's circle of strain with radius √[((ε_x − ε_y)/2)² + (γ_xy/2)²].
A rectangular rosette has gauges at 0°, 45° and 90°. The 0° and 90° gauges read ε_x and ε_y directly and the 45° gauge gives the shear strain through γ_xy = 2ε_45 − ε_0 − ε_90. A delta rosette has gauges at 0°, 60° and 120°, spread evenly round the circle; it is less sensitive to the gauge orientation and gives ε_x = ε_0, ε_y = (2ε_60 + 2ε_120 − ε_0)/3 and γ_xy = 2(ε_60 − ε_120)/√3. From ε_x, ε_y and γ_xy the principal strains follow from the same formula as principal stresses.
For an isotropic linear elastic material, the principal strain directions are also the principal stress directions, because shear stress and shear strain vanish together. The surface of a member is in plane stress, so σ₁ = E(ε₁ + ν ε₂)/(1 − ν²) and σ₂ = E(ε₂ + ν ε₁)/(1 − ν²), with E and ν the elastic constants of lesson 1.3. The strain through the thickness is not zero; it is ε₃ = −ν(ε₁ + ε₂)/(1 − ν). This is why a surface gauge on a plate in plane stress is not the same as plane strain, where ε₃ = 0 and σ₃ is not zero, as in a long retaining wall or a dam section.
Derivation
- Let a line element of length ds at angle θ have projections dx = ds cos θ and dy = ds sin θ. Under strains ε_x, ε_y and shear strain γ_xy, its end moves by du = ε_x dx + γ_xy dy (shear taken as a sliding of x past y) and dv = ε_y dy.
- The stretch along the line is the component of the movement along it: ε_θ ds = du cos θ + dv sin θ, which gives ε_θ = ε_x cos² θ + ε_y sin² θ + γ_xy sin θ cos θ.
- With double angles: ε_θ = (ε_x + ε_y)/2 + (ε_x − ε_y)/2 × cos 2θ + (γ_xy/2) sin 2θ, and similarly γ_θ/2 = −(ε_x − ε_y)/2 × sin 2θ + (γ_xy/2) cos 2θ. These match the stress equations with τ → γ/2.
- Principal strains: ε₁,₂ = (ε_x + ε_y)/2 ± √[((ε_x − ε_y)/2)² + (γ_xy/2)²]; tan 2θ_p = γ_xy/(ε_x − ε_y); maximum in-plane shear strain γ_max = ε₁ − ε₂.
- Rectangular rosette: ε_45 = (ε_x + ε_y)/2 + γ_xy/2, so γ_xy = 2ε_45 − ε_0 − ε_90 with ε_x = ε_0, ε_y = ε_90.
- Delta rosette: ε_60 = ε_x/4 + 3ε_y/4 + (√3/4) γ_xy and ε_120 = ε_x/4 + 3ε_y/4 − (√3/4) γ_xy. Subtracting, γ_xy = 2(ε_60 − ε_120)/√3; adding, ε_y = (2ε_60 + 2ε_120 − ε_0)/3.
- Plane stress Hooke's law: ε₁ = (σ₁ − ν σ₂)/E and ε₂ = (σ₂ − ν σ₁)/E. Solving, σ₁ = E(ε₁ + ν ε₂)/(1 − ν²) and σ₂ = E(ε₂ + ν ε₁)/(1 − ν²).
ε_θ = (ε_x + ε_y)/2 + (ε_x − ε_y)/2 × cos 2θ + (γ_xy/2) sin 2θε₁,₂ = (ε_x + ε_y)/2 ± √[((ε_x − ε_y)/2)² + (γ_xy/2)²]; tan 2θ_p = γ_xy/(ε_x − ε_y); γ_max = ε₁ − ε₂Rectangular rosette: ε_x = ε_0, ε_y = ε_90, γ_xy = 2ε_45 − ε_0 − ε_90Delta rosette: ε_x = ε_0, ε_y = (2ε_60 + 2ε_120 − ε_0)/3, γ_xy = 2(ε_60 − ε_120)/√3Plane stress: σ₁ = E(ε₁ + ν ε₂)/(1 − ν²), σ₂ = E(ε₂ + ν ε₁)/(1 − ν²); ε₃ = −ν(ε₁ + ε₂)/(1 − ν)Units: strain in microstrain (µε = 10⁻⁶); E in N/mm² gives σ in N/mm²
- Small strains, so products of strains are neglected and angles change by small amounts.
- The three gauges measure the strain at effectively one point; the rosette is small compared with the stress gradient.
- For converting strain to stress: isotropic, homogeneous, linear elastic material with known E and ν, and plane stress at the gauged surface.
- Gauge readings are corrected for temperature and lead-wire effects before reduction.
- Limits: concrete cracks, creeps and shrinks, so stresses inferred from strains on concrete are approximate and need the effective modulus for the load duration.
Codes and standards
Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.
- Strain transformation and rosette reduction are mechanics; no design code governs the derivation or the formulas of this lesson.
- Load tests of bridges and buildings use strain gauges as one of several measurements; the test procedure and acceptance criteria are set by the owner's specification and the applicable national guidance, while the reduction of rosette readings is the mechanics shown here.
- Side by side, not ranked: Indian, European and American practice for structural testing and monitoring all reduce rosette readings with the same transformation equations.
Worked examples
Problem. A 0°/45°/90° rosette on the web of a steel plate girder, with the 0° gauge along the girder, reads ε_0 = 500 µε, ε_45 = 350 µε and ε_90 = −100 µε under a test load. E = 200 000 N/mm², ν = 0.3. Find the principal strains, their direction, the maximum shear strain and the principal stresses.
- ε_x = 500, ε_y = −100, γ_xy = 2 × 350 − 500 + 100 = 300 µε.
- Average = 200 µε; R = √(300² + 150²) = 335.4 µε; ε₁ = 535.4 µε, ε₂ = −135.4 µε; γ_max = 670.8 µε.
- tan 2θ_p = 300/600 = 0.5, 2θ_p = 26.57°, θ₁ = 13.28° from the girder axis.
- E/(1 − ν²) = 219 780 N/mm²; σ₁ = 219 780 × (535.4 − 0.3 × 135.4) × 10⁻⁶ = 108.7 N/mm².
- σ₂ = 219 780 × (−135.4 + 0.3 × 535.4) × 10⁻⁶ = 5.5 N/mm².
Answer. ε₁ = 535.4 µε at 13.3°, ε₂ = −135.4 µε, γ_max = 670.8 µε; σ₁ = 108.7, σ₂ = 5.5 N/mm²
Problem. A 0°/60°/120° rosette on a steel pipe pile during a load test reads ε_0 = 300 µε, ε_60 = 400 µε and ε_120 = −100 µε. E = 200 000 N/mm², ν = 0.3. Find ε_x, ε_y, γ_xy, the principal strains and stresses.
- ε_x = 300 µε; ε_y = (2 × 400 + 2 × (−100) − 300)/3 = 100 µε.
- γ_xy = 2(400 + 100)/√3 = 577.4 µε.
- Average = 200 µε; R = √(100² + 288.7²) = 305.5 µε; ε₁ = 505.5 µε, ε₂ = −105.5 µε; θ₁ = ½ atan(577.4/200) = 35.4°.
- σ₁ = 219 780 × (505.5 − 0.3 × 105.5) × 10⁻⁶ = 104.1 N/mm²; σ₂ = 219 780 × (−105.5 + 0.3 × 505.5) × 10⁻⁶ = 10.1 N/mm².
- Check: ε_θ at 60° from the reduced values = 200 − 50 + 250 = 400 µε, the 60° reading.
Answer. ε_x = 300, ε_y = 100, γ_xy = 577.4 µε; ε₁ = 505.5, ε₂ = −105.5 µε; σ₁ = 104.1, σ₂ = 10.1 N/mm²
Problem. From a rosette on the soffit of a concrete deck slab, ε_x = −200 µε, ε_y = 100 µε and γ_xy = 150 µε. Find the normal strain along a line at 30° to x, the principal strains and the through-thickness strain, taking ν = 0.2.
- Average = −50 µε; half-difference = −150 µε; γ_xy/2 = 75 µε; 2θ = 60°.
- ε_30 = −50 − 150 × 0.5 + 75 × 0.866 = −60.0 µε.
- R = √(150² + 75²) = 167.7 µε; ε₁ = 117.7 µε, ε₂ = −217.7 µε.
- ε₃ = −0.2 × (117.7 − 217.7)/0.8 = +25.0 µε (the slab thickens slightly, since the in-plane strains are mostly compressive).
- Concrete strains this small are in the uncracked range; for sustained loads the effective modulus must be used if stresses are needed.
Answer. ε_30 = −60.0 µε; ε₁ = 117.7, ε₂ = −217.7 µε; ε₃ = 25.0 µε
Step-by-step procedure
- Record the rosette type, the gauge angles and the direction of the 0° gauge on the member.
- Correct the readings for temperature and zero drift, and convert to microstrain.
- Reduce to ε_x, ε_y and γ_xy with the rectangular or delta formulas.
- Compute the principal strains, their direction and the maximum shear strain.
- Convert to principal stresses with plane stress Hooke's law, and check one gauge reading back with the transformation equation.
Site notes
- In bridge load tests, rosettes are placed where the principal directions are not known in advance, such as webs near supports; single gauges suffice where the stress is clearly along the member.
- Gauges must be bonded to clean, smooth parent metal or sound concrete; on concrete, long-gauge-length gauges average over the aggregate.
- Temperature changes during a test can swamp the load strains; use temperature-compensated gauges or a dummy gauge and take zero readings just before loading.
- Record which way the 0° gauge points on the structure; a rosette reduced with the wrong reference direction gives correct principal values but wrong directions.
- Using γ_xy instead of γ_xy/2 in the transformation and principal strain formulas.
- Treating the 45° gauge reading as the shear strain itself.
- Converting principal strains to stress with σ = E ε, ignoring Poisson's effect.
- Assuming the through-thickness strain is zero at a free surface (that is plane strain, not plane stress).
- Mixing microstrain and strain, giving stresses out by a factor of 10⁶.
Strain transforms exactly like stress if you replace τ by γ/2; for a rectangular rosette the shear strain is 2ε_45 − ε_0 − ε_90.
Summary
- ε_θ = (ε_x + ε_y)/2 + (ε_x − ε_y)/2 × cos 2θ + (γ_xy/2) sin 2θ.
- Principal strains and Mohr's circle of strain follow from the stress results with τ → γ/2.
- Rectangular and delta rosettes give ε_x, ε_y and γ_xy from three readings.
- For isotropic elastic materials, principal strain and stress directions coincide; σ₁ = E(ε₁ + ν ε₂)/(1 − ν²).
- Plane stress at a surface has ε₃ ≠ 0; plane strain has ε₃ = 0.
Practice questions
Tap a question to see the answer.
1ε_x = 400 µε, ε_y = −200 µε, γ_xy = 300 µε. Find ε₁, ε₂ and γ_max.
Average 100, R = √(300² + 150²) = 335.4; ε₁ = 435.4 µε, ε₂ = −235.4 µε, γ_max = 670.8 µε.
2A rectangular rosette reads ε_0 = 200, ε_45 = 300 and ε_90 = 100 µε. Find ε_x, ε_y and γ_xy.
ε_x = 200 µε, ε_y = 100 µε, γ_xy = 2 × 300 − 200 − 100 = 300 µε.
3On a steel surface ε₁ = 500 µε and ε₂ = 100 µε; E = 200 000 N/mm², ν = 0.3. Find σ₁ and σ₂.
σ₁ = 219 780 × (500 + 30) × 10⁻⁶ = 116.5 N/mm²; σ₂ = 219 780 × (100 + 150) × 10⁻⁶ = 54.9 N/mm².
4Why does a rosette need three gauges?
The plane strain state has three unknowns, ε_x, ε_y and γ_xy, and each gauge gives one equation, so three independent directions are needed.
5A delta rosette reads 100 µε on all three gauges. What is the state of strain?
ε_x = 100, ε_y = (200 + 200 − 100)/3 = 100 µε, γ_xy = 0: equal biaxial strain, 100 µε in every direction.
6ε_x = 300 µε, ε_y = 100 µε and γ_xy = 0. Find the normal strain at 45°.
ε_45 = 200 + 100 cos 90° + 0 = 200 µε.
References
Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.
- B. J. Goodno, J. M. Gere, Mechanics of Materials, Cengage Learning, 9th edition, 2018.
- R. C. Hibbeler, Mechanics of Materials, Pearson, 10th edition, 2016.
- F. P. Beer, E. R. Johnston, J. T. DeWolf, D. F. Mazurek, Mechanics of Materials, McGraw Hill, 8th edition, 2020.
- E. P. Popov, Engineering Mechanics of Solids, Prentice Hall, 2nd edition, 1998.