7.1 Stresses on inclined planes
After this lesson you should be able to:
- Explain why the stress at a point depends on the plane through the point, and find the normal and shear stress on an inclined plane of a bar in axial load.
- Derive the plane-stress transformation equations from equilibrium of a small wedge, with a clear sign convention.
- Use the transformation equations to find stresses on inclined welds, glued joints, timber grain and other planes met in civil work, and check results with the invariant σ_x + σ_y.
Theory
Earlier chapters found stresses on cross-sections square to the member axis: σ = N/A in a tie, σ = M y/I in a beam, τ = V Q/(I b) for beam shear and τ = T r/J in a shaft. A cross-section is only one of infinitely many planes through a point. Joints, cracks, timber grain, rock joints and weld lines are often inclined, and materials often fail on inclined planes, so we need the stresses on any plane, not just on the cross-section.
Consider first a bar in axial tension with stress σ = P/A on the cross-section. Cut it on a plane whose outward normal makes an angle θ with the bar axis. The inclined face has a larger area A/cos θ, and the axial force P can be split into a part P cos θ normal to the face and a part P sin θ along it. Dividing by the face area gives σ_θ = σ cos² θ and τ_θ = σ sin θ cos θ = (σ/2) sin 2θ. The normal stress is largest on the cross-section (θ = 0), and the shear stress is largest, equal to σ/2, on planes at 45°. This is why ductile steel coupons show slip lines at about 45° and why a short concrete cylinder crushed in compression often breaks on inclined cones.
In two-dimensional or plane stress the state at a point is known from three numbers on two perpendicular faces: σ_x, σ_y and τ_xy. Plane stress applies at the free surfaces of members and in thin plates such as girder webs, gusset plates and tank walls, where the stresses through the thickness are negligible. We use these sign conventions throughout this chapter: normal stress is positive in tension; τ_xy is positive when it acts in the +y direction on the face whose outward normal is +x; and the angle θ is measured anticlockwise from the x-axis to the outward normal of the inclined plane.
Equilibrium of a small triangular wedge gives the stresses on the inclined plane in terms of σ_x, σ_y, τ_xy and the double angle 2θ. Two useful facts follow. The normal stresses on any two perpendicular planes add to the same total, σ_x + σ_y, whatever the orientation; this is the first stress invariant and is a fast check on arithmetic. And the shear stresses on two perpendicular planes are equal in size and opposite in sign under our convention, which is the complementary shear stress property met in lesson 1.1.
Derivation
- Take a wedge with a vertical face (normal −x), a horizontal face (normal −y) and an inclined face of area dA whose outward normal n makes angle θ with the x-axis. The vertical face has area dA cos θ and the horizontal face dA sin θ (unit thickness).
- Forces on the vertical face: σ_x dA cos θ in −x and τ_xy dA cos θ in −y. Forces on the horizontal face: σ_y dA sin θ in −y and τ_xy dA sin θ in −x.
- Equilibrium along n = (cos θ, sin θ): σ_θ dA = σ_x dA cos² θ + σ_y dA sin² θ + 2 τ_xy dA sin θ cos θ.
- Equilibrium along t = (−sin θ, cos θ): τ_θ dA = −(σ_x − σ_y) dA sin θ cos θ + τ_xy dA (cos² θ − sin² θ).
- Using cos² θ = (1 + cos 2θ)/2, sin² θ = (1 − cos 2θ)/2 and 2 sin θ cos θ = sin 2θ: σ_θ = (σ_x + σ_y)/2 + (σ_x − σ_y)/2 × cos 2θ + τ_xy sin 2θ and τ_θ = −(σ_x − σ_y)/2 × sin 2θ + τ_xy cos 2θ.
- Uniaxial case (σ_y = τ_xy = 0, σ_x = σ): σ_θ = σ cos² θ and τ_θ = −(σ/2) sin 2θ; the size of the shear stress peaks at σ/2 when θ = 45°.
- Invariant: replacing θ by θ + 90° changes the sign of cos 2θ and sin 2θ, so σ_θ + σ_(θ+90°) = σ_x + σ_y, and τ_(θ+90°) = −τ_θ.
σ_θ = (σ_x + σ_y)/2 + (σ_x − σ_y)/2 × cos 2θ + τ_xy sin 2θ (N/mm²)τ_θ = −(σ_x − σ_y)/2 × sin 2θ + τ_xy cos 2θ (N/mm²)Uniaxial: σ_θ = σ cos² θ; |τ_θ| = (σ/2) sin 2θ, largest σ/2 at θ = 45°Invariant: σ_θ + σ_(θ+90°) = σ_x + σ_y; τ_(θ+90°) = −τ_θSign convention: tension positive; τ_xy positive in +y on the +x face; θ anticlockwise from x to the plane's outward normal
- Plane stress: the stresses σ_z, τ_xz and τ_yz on the faces normal to the thickness are zero, as at a free surface or in a thin plate.
- The stresses are uniform over the small wedge, so the result applies at a point; the wedge is shrunk to zero size.
- Equilibrium alone is used, so the equations hold for any material, elastic or not, isotropic or not.
- Body forces such as self-weight are of higher order for a vanishing wedge and drop out.
- Limits: the strength of a joint, grain or weld on the inclined plane is a separate question; the equations give only the stress acting on it.
Codes and standards
Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.
- The transformation of stress is mechanics; no design code governs the derivation or the equations of this lesson.
- Design codes use these results inside their own checks, for example when a weld or a joint is inclined to the load, or when shear and normal stress act together in a plate; each code then adds its own strengths and safety factors.
- Side by side, not ranked: the Indian steel and concrete codes, the European codes (EN 1993-1-1, EN 1992-1-1) and the American codes (AISC 360, ACI 318) all rely on the same equilibrium of an element, so the equations here are common to all of them.
Worked examples
Problem. A steel tie of cross-section 2000 mm² carries an axial tension of 300 kN. It is spliced by a full-penetration butt weld whose plane has its normal at 30° to the bar axis. Find the normal and shear stress on the weld plane, and the largest shear stress anywhere in the bar.
- Axial stress σ = 300 000/2000 = 150 N/mm².
- Normal stress on the weld: σ_θ = σ cos² 30° = 150 × 0.75 = 112.5 N/mm².
- Shear stress on the weld: |τ_θ| = (σ/2) sin 60° = 75 × 0.866 = 65.0 N/mm².
- Largest shear stress in the bar: σ/2 = 75 N/mm², on planes at 45°.
Answer. σ_θ = 112.5 N/mm², |τ_θ| = 65.0 N/mm² on the weld; τ_max = 75 N/mm² at 45°
Problem. A 150 × 150 mm timber post carries an axial compression of 135 kN. The grain runs at 20° to the post axis, so the plane along the grain has its normal at 70° to the axis. Find the shear stress along the grain and the normal stress across it.
- σ = −135 000/(150 × 150) = −6.0 N/mm² (compression).
- On the grain plane (θ = 70°): σ_θ = σ cos² 70° = −6.0 × 0.1170 = −0.70 N/mm² (compression across the grain).
- |τ_θ| = (|σ|/2) sin 140° = 3.0 × 0.6428 = 1.93 N/mm² (shear along the grain).
- Timber is much weaker in shear along the grain than in compression parallel to it, so the shear stress along a sloping grain is the value to check against the timber's grade strength.
Answer. Shear along the grain 1.93 N/mm²; compression across the grain 0.70 N/mm²
Problem. At a point in a welded plate girder web near a support, σ_x = 80 N/mm² (bending tension along the girder), σ_y = 0 and τ_xy = 30 N/mm². A web splice weld lies on a plane whose normal is at 30° anticlockwise from the girder axis. Find the stresses on the weld plane and on the plane at right angles to it.
- Average (σ_x + σ_y)/2 = 40; half-difference (σ_x − σ_y)/2 = 40; 2θ = 60°.
- σ_θ = 40 + 40 cos 60° + 30 sin 60° = 40 + 20 + 25.98 = 85.98 N/mm².
- τ_θ = −40 sin 60° + 30 cos 60° = −34.64 + 15.00 = −19.64 N/mm².
- At θ = 120°: σ = 40 + 40 cos 240° + 30 sin 240° = 40 − 20 − 25.98 = −5.98 N/mm², τ = +19.64 N/mm².
- Check: 85.98 + (−5.98) = 80 = σ_x + σ_y.
Answer. Weld plane 86.0 N/mm² normal, 19.6 N/mm² shear; perpendicular plane −6.0 N/mm²
Step-by-step procedure
- Draw the stress element and mark σ_x, σ_y and τ_xy with their signs (tension positive; τ_xy positive in +y on the +x face).
- Find the angle θ from the x-axis to the outward normal of the plane of interest, anticlockwise positive.
- Compute the average stress, the half-difference and 2θ.
- Substitute in the transformation equations for σ_θ and τ_θ.
- Check with σ_θ + σ_(θ+90°) = σ_x + σ_y, and interpret the signs of the results on a sketch.
Site notes
- Butt welds, glued scarf joints in timber and construction joints in concrete are often inclined to the main stress; the stress acting on the joint, not the stress on the cross-section, decides whether it holds.
- Timber with sloping grain is weaker than straight-grained timber, because a share of the axial stress becomes shear along the grain; grading rules limit the slope of grain for this reason.
- Rock joints and bedding planes in cuttings and tunnels are inclined planes; the same equations give the normal and shear stress on them, as used in rock and soil mechanics.
- Inclined cracks in concrete beams near supports follow the planes of largest tension, which the next lesson locates.
- Measuring θ to the plane itself instead of to its normal, which swaps the cos and sin parts.
- Forgetting the double angle 2θ in the transformation equations.
- Mixing sign conventions for τ_xy between the element and the formula.
- Taking the largest normal stress as the only danger and ignoring the shear on inclined planes.
- Using the cross-section area instead of the inclined area when resolving forces by hand.
For a bar in axial stress σ, the shear stress on any plane never exceeds σ/2, reached at 45°, and the normal stresses on any two perpendicular planes always add up to σ_x + σ_y.
Summary
- The stress on a plane depends on the plane's orientation; the cross-section is only one choice.
- Wedge equilibrium gives σ_θ and τ_θ in terms of σ_x, σ_y, τ_xy and 2θ.
- For axial stress σ: σ_θ = σ cos² θ and the largest shear is σ/2 at 45°.
- σ_x + σ_y is invariant; perpendicular planes carry equal and opposite shear.
- State the sign convention before every calculation.
Practice questions
Tap a question to see the answer.
1A bar has an axial tensile stress of 100 N/mm². Find the normal and shear stress on a plane whose normal makes 60° with the axis.
σ_θ = 100 cos² 60° = 25 N/mm²; |τ_θ| = 50 sin 120° = 43.3 N/mm².
2On which planes is the shear stress largest in a bar under axial stress σ, and what is its value?
On planes at 45° to the axis; |τ|max = σ/2, with normal stress σ/2 on the same planes.
3σ_x = 60 N/mm², σ_y = −40 N/mm², τ_xy = 0. Find σ_θ and τ_θ for θ = 45°.
σ_θ = 10 + 50 cos 90° + 0 = 10 N/mm²; τ_θ = −50 sin 90° = −50 N/mm².
4A point is in pure shear with τ_xy = 50 N/mm². Find the normal stresses on the planes at 45° and 135°.
σ_45 = 50 sin 90° = +50 N/mm² (tension); σ_135 = 50 sin 270° = −50 N/mm²; the shear on both planes is zero.
5σ_x = 70 N/mm² and σ_y = 30 N/mm². On a certain plane σ_θ = 80 N/mm². What is the normal stress on the perpendicular plane?
σ_(θ+90°) = σ_x + σ_y − σ_θ = 100 − 80 = 20 N/mm².
6σ_x = 80 N/mm², σ_y = 20 N/mm², τ_xy = 20 N/mm². Find σ_θ and τ_θ for θ = 60°.
Average 50, half-difference 30, 2θ = 120°: σ_θ = 50 − 15 + 17.32 = 52.32 N/mm²; τ_θ = −25.98 − 10 = −35.98 N/mm².
References
Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.
- B. J. Goodno, J. M. Gere, Mechanics of Materials, Cengage Learning, 9th edition, 2018.
- R. C. Hibbeler, Mechanics of Materials, Pearson, 10th edition, 2016.
- F. P. Beer, E. R. Johnston, J. T. DeWolf, D. F. Mazurek, Mechanics of Materials, McGraw Hill, 8th edition, 2020.
- E. P. Popov, Engineering Mechanics of Solids, Prentice Hall, 2nd edition, 1998.