Indiacon CivilSubscribe

Textbook › Strength of Materials › Chapter 7 › Lesson 7.3

7.3 Mohr's circle of stress

Strength of Materials Chapter 7: Transformation of stress and strain Under review — not yet three-checked Author: Indiacon

Learning objectives

After this lesson you should be able to:

  • Construct Mohr's circle for plane stress from σ_x, σ_y and τ_xy, using a stated plotting rule.
  • Read principal stresses, maximum shear stress and the stresses on any inclined plane from the circle, and relate angles on the circle (2θ) to angles on the element (θ).
  • Recognise the special circles for uniaxial stress, pure shear and equal biaxial stress, and see why soil and rock mechanics use the same construction.

Theory

In 1882 Otto Mohr showed that the transformation equations of lesson 7.1 describe a circle. If we eliminate 2θ by squaring and adding, (σ_θ − σ_avg)² + τ_θ² = R², where σ_avg = (σ_x + σ_y)/2 and R is the radius found in lesson 7.2. Every possible plane through the point is therefore one point on a circle in the σ–τ plane, with centre (σ_avg, 0) and radius R. The circle turns the algebra into a picture that shows at a glance the largest and smallest normal stresses and the largest shear.

We plot normal stress σ horizontally (tension to the right) and shear stress τ vertically with positive τ plotted downward. The face whose normal is x is plotted as point X = (σ_x, τ_xy) and the face whose normal is y as point Y = (σ_y, −τ_xy). X and Y lie at opposite ends of a diameter, because their planes are 90° apart on the element and 180° apart on the circle. With this plotting rule, turning the plane anticlockwise through θ on the element moves the point anticlockwise through 2θ on the circle, so the senses of rotation agree.

στ (+ down)CX (σx, τxy)Y (σy, −τxy)σ1σ2R2θpτmax = RIndiacon original
Figure 7.3: Mohr's circle of stress: X and Y at the ends of a diameter, principal stresses on the σ-axis and the maximum shear equal to the radius. Indiacon original, not to scale.

The circle meets the σ-axis at the principal stresses σ₁ = σ_avg + R and σ₂ = σ_avg − R, where the shear is zero. The top and bottom points of the circle give the maximum in-plane shear stress R, with the normal stress σ_avg. The angle from X to the σ₁ point, measured on the circle, is 2θ₁; on the element the principal plane is at half that angle in the same sense. Any other plane is found by stepping round the circle by twice the plane's angle.

Three special cases are worth remembering. Uniaxial stress σ gives a circle passing through the origin with radius σ/2, which is why the largest shear is σ/2. Pure shear τ gives a circle centred on the origin with radius τ, so principal stresses ±τ act at 45°. Equal biaxial stress (σ_x = σ_y, τ_xy = 0), as in a thin spherical shell or a point under hydrostatic water pressure, shrinks the circle to a point: every plane carries the same normal stress and no shear. In soil and rock mechanics the same circle is drawn, usually with compression taken as positive, and the Mohr–Coulomb failure line is drawn tangent to it.

Derivation

  1. From lesson 7.1: σ_θ − σ_avg = a cos 2θ + τ_xy sin 2θ and τ_θ = −a sin 2θ + τ_xy cos 2θ, where a = (σ_x − σ_y)/2.
  2. Square and add: (σ_θ − σ_avg)² + τ_θ² = a² (cos² 2θ + sin² 2θ) + τ_xy² (sin² 2θ + cos² 2θ) + 2a τ_xy (cos 2θ sin 2θ − sin 2θ cos 2θ) = a² + τ_xy² = R².
  3. So every (σ_θ, τ_θ) lies on a circle with centre (σ_avg, 0) and radius R = √(a² + τ_xy²).
  4. Point X (θ = 0) is (σ_x, τ_xy); point Y (θ = 90°) is (σ_y, −τ_xy). Their midpoint is (σ_avg, 0), so XY is a diameter.
  5. The vector from the centre to the plane point is (a cos 2θ + τ_xy sin 2θ, −a sin 2θ + τ_xy cos 2θ), which is the vector (a, τ_xy) rotated clockwise by 2θ in ordinary axes. With τ plotted downward the vertical axis is flipped, so the rotation appears anticlockwise on the drawing, the same sense as θ on the element.
  6. At the σ-axis crossings τ = 0, giving σ₁,₂ = σ_avg ± R; at the top and bottom points |τ| = R with σ = σ_avg, as found in lesson 7.2.
Formulas, symbols and SI units
  • Centre C = (σ_x + σ_y)/2 on the σ-axis; radius R = √[((σ_x − σ_y)/2)² + τ_xy²]
  • Plot X = (σ_x, τ_xy), Y = (σ_y, −τ_xy), τ positive downward; XY is a diameter
  • σ₁ = C + R, σ₂ = C − R; τ_max = R at σ = C
  • Plane at θ on the element ↔ point at 2θ on the circle, same sense of rotation
  • Plane at θ from the σ₁ plane: σ = C + R cos 2θ, |τ| = R sin 2θ
  • Equation of the circle: (σ − C)² + τ² = R²
Assumptions and limits
  • Plane stress, as in lessons 7.1 and 7.2; for a three-dimensional state three circles are drawn, one for each pair of principal stresses.
  • The plotting rule (τ positive downward, X = (σ_x, τ_xy)) must be stated; other textbooks use the opposite rule with clockwise-positive shear plotted upward, which gives the same answers when applied consistently.
  • The circle is exact; a drawn circle is limited only by drawing accuracy, so key values are computed from the centre and radius.
  • Equilibrium only; valid for any material.
  • Limits: the circle shows stresses, not strength; failure envelopes are added separately (lesson 7.5, and shear strength of soils).

Codes and standards

Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.

  • Mohr's circle is a construction of mechanics; no design code governs it.
  • In geotechnical practice the circle is used to interpret laboratory shear tests and to judge stability, with the strength parameters coming from tests on the actual soil; the Indian, European (EN 1997-1) and American practices all draw the same circle and are listed side by side, not ranked.
  • For structural design, codes give strengths and safety factors; the circle only supplies the stresses to compare with them.

Worked examples

Example 1 (soil element behind a retaining wall)

Problem. At a point in the backfill of a retaining wall, the stresses are σ_x = −40 kPa (horizontal), σ_y = −100 kPa (vertical), both compressive, with τ_xy = 20 kPa. Using Mohr's circle with tension positive, find the principal stresses and the stresses on a plane whose normal is at 30° anticlockwise from the horizontal.

  1. C = (−40 − 100)/2 = −70 kPa; R = √(30² + 20²) = √1300 = 36.06 kPa.
  2. σ₁ = −70 + 36.06 = −33.94 kPa (minor compression); σ₂ = −70 − 36.06 = −106.06 kPa (major compression).
  3. X = (−40, 20). For θ = 30°, step 60° round the circle: σ = −70 + 30 cos 60° + 20 sin 60° = −70 + 15 + 17.32 = −37.68 kPa.
  4. τ = −30 sin 60° + 20 cos 60° = −25.98 + 10 = −15.98 kPa.
  5. In soil mechanics, with compression positive, the major and minor principal stresses are 106.1 and 33.9 kPa; the circle is the same, mirrored.

Answer. Principal 106.1 and 33.9 kPa compression; on the 30° plane σ = −37.7 kPa, τ = −16.0 kPa

Example 2 (gusset plate at a truss joint)

Problem. A point in a steel gusset plate has σ_x = −20 N/mm², σ_y = 60 N/mm² and τ_xy = −30 N/mm². Draw Mohr's circle and find the principal stresses, their directions and the maximum shear stress.

  1. C = (−20 + 60)/2 = 20 N/mm²; R = √(40² + 30²) = 50 N/mm².
  2. σ₁ = 70 N/mm², σ₂ = −30 N/mm², τ_max = 50 N/mm².
  3. X = (−20, −30) and Y = (60, 30). The angle on the circle from X to the σ₁ point is 2θ₁ = atan2(2τ_xy, σ_x − σ_y) = atan2(−60, −80) = −143.13°, i.e. 216.87° anticlockwise.
  4. On the element θ₁ = 108.43° (equivalently −71.57°): σ₁ = 70 N/mm² acts nearly along y, turned 18.43° past it; σ₂ acts at 18.43°.
  5. Check by the transformation equation at θ = 108.43°: σ = 20 − 40 cos 216.87° − 30 sin 216.87° = 20 + 32 + 18 = 70 N/mm².

Answer. σ₁ = 70 N/mm² at 108.4°, σ₂ = −30 N/mm² at 18.4°; τ_max = 50 N/mm²

Example 3 (special circles: rebar in tension and a submerged element)

Problem. Draw Mohr's circle for (a) a reinforcing bar under an axial tensile stress of 250 N/mm², and (b) a point in a thin plate under equal in-plane water pressure of 0.3 N/mm² on both axes with no shear. Give the largest shear stress in each.

  1. (a) X = (250, 0), Y = (0, 0): C = 125 N/mm², R = 125 N/mm²; the circle passes through the origin.
  2. σ₁ = 250, σ₂ = 0; τ_max = 125 N/mm² on planes at 45°, with normal stress 125 N/mm² on them.
  3. (b) X = Y = (−0.3, 0): C = −0.3 N/mm², R = 0; the circle is a point.
  4. Every plane carries −0.3 N/mm² and zero shear, which is why equal all-round pressure alone does not cause shear failure.

Answer. (a) τ_max = 125 N/mm² at 45°; (b) circle is a point, τ = 0 on every plane

Step-by-step procedure

  1. Set axes: σ horizontal (tension right), τ vertical with positive τ downward; state the rule on the sketch.
  2. Plot X = (σ_x, τ_xy) and Y = (σ_y, −τ_xy); join them; the crossing with the σ-axis is the centre C.
  3. Compute R = CX and read σ₁ = C + R, σ₂ = C − R and τ_max = R.
  4. Measure 2θ from CX to the point wanted (σ₁ or a given plane), in the same sense as θ on the element.
  5. Halve the angle for the element, sketch the rotated element and confirm one value with the transformation equations.

Site notes

  • Mohr's circle is the standard picture for interpreting triaxial and direct shear tests on soil, linking measured stresses at failure to the strength parameters used in foundation and slope design.
  • For steel and concrete, a quick circle on the back of a calculation sheet catches sign errors in principal stresses from software output.
  • Strain-gauge readings on bridges and buildings are turned into stresses and then into principal stresses with the same construction (lesson 7.4).
  • When explaining crack directions to a site team, a circle drawn beside the element shows why cracks run at an angle.
Common mistakes
  • Plotting X and Y with the same shear sign, so they are not ends of a diameter.
  • Using θ instead of 2θ on the circle.
  • Rotating in the wrong sense because the plotting rule was not stated.
  • Reading σ₂ as the smaller magnitude instead of the algebraically smaller value.
  • Forgetting that a circle through two compressive points still has its centre and radius computed with signs.
Quick check

Centre = average of σ_x and σ_y, radius = √(half-difference² + τ_xy²); principal stresses are centre ± radius, and the maximum shear is the radius.

Summary

  • All planes through a point map onto one circle with centre (σ_x + σ_y)/2 and radius R.
  • X = (σ_x, τ_xy) and Y = (σ_y, −τ_xy) are ends of a diameter, with τ plotted downward.
  • An angle θ on the element is 2θ on the circle, in the same sense.
  • σ₁, σ₂ are where the circle meets the σ-axis; τ_max = R at the top and bottom.
  • Uniaxial stress, pure shear and equal biaxial stress give recognisable special circles.

Practice questions

Tap a question to see the answer.

1σ_x = 120, σ_y = 40, τ_xy = 30 N/mm². Find C, R, σ₁, σ₂, τ_max and θ₁ from Mohr's circle.

C = 80, R = √(40² + 30²) = 50; σ₁ = 130, σ₂ = 30 N/mm²; τ_max = 50 N/mm²; 2θ₁ = atan(60/80) = 36.87°, θ₁ = 18.43°.

2For the state of Q1, find σ and τ on the plane at θ = 45°.

Step 90° from X: σ = 80 + 40 cos 90° + 30 sin 90° = 110 N/mm²; τ = −40 sin 90° + 30 cos 90° = −40 N/mm².

3A Mohr's circle has centre 30 N/mm² and radius 50 N/mm². Give the principal stresses and the maximum in-plane shear.

σ₁ = 80 N/mm², σ₂ = −20 N/mm², τ_max = 50 N/mm².

4The principal stresses at a point are 100 and 20 N/mm². Find the normal and shear stress on a plane whose normal is at 30° to the σ₁ direction.

C = 60, R = 40: σ = 60 + 40 cos 60° = 80 N/mm²; |τ| = 40 sin 60° = 34.6 N/mm².

5Describe Mohr's circle for pure shear of 70 N/mm².

Centre at the origin, radius 70 N/mm²; principal stresses ±70 N/mm² on planes at 45° to the shear planes.

6σ_x = σ_y = −50 N/mm² and τ_xy = 0. What is the circle and the shear on any plane?

The circle is a point at −50 N/mm²; every plane carries −50 N/mm² normal stress and zero shear.

References

Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.

  • B. J. Goodno, J. M. Gere, Mechanics of Materials, Cengage Learning, 9th edition, 2018.
  • R. C. Hibbeler, Mechanics of Materials, Pearson, 10th edition, 2016.
  • F. P. Beer, E. R. Johnston, J. T. DeWolf, D. F. Mazurek, Mechanics of Materials, McGraw Hill, 8th edition, 2020.
  • E. P. Popov, Engineering Mechanics of Solids, Prentice Hall, 2nd edition, 1998.
Suggest a correction

If something on this page is wrong, tell the editor. Your message is sent privately and is not published.

Sent privately to the Indiacon editor; not published.