3.1 Laws of dry friction and angle of friction
After this lesson you should be able to:
- State the laws of dry (Coulomb) friction and distinguish static from kinetic friction.
- Define the angle of friction, the cone of friction and the angle of repose, and relate them to the coefficient of friction.
- Decide whether a body at rest will stay at rest, and find the force needed to start motion.
Theory
When two dry surfaces are pressed together and one tends to slide over the other, a tangential force develops at the contact that opposes the relative motion. This is friction. It is not a fixed force: it takes whatever value equilibrium needs, from zero up to a limit. The limit is proportional to the normal force, F_max = μs N, where μs is the coefficient of static friction for that pair of surfaces.
Once sliding starts, the friction force drops to a roughly constant value F = μk N, where μk, the coefficient of kinetic friction, is usually somewhat smaller than μs. This is why it takes more effort to start a heavy crate moving than to keep it moving. The classical laws, from the experiments of Amontons and Coulomb, say that limiting friction is proportional to the normal force, is nearly independent of the apparent contact area, and (for kinetic friction) is nearly independent of sliding speed at ordinary speeds. They are empirical approximations, good for dry surfaces, not for lubricated contacts.
The normal reaction N and the friction force F combine into a total reaction R inclined to the normal. At impending slip its angle is the angle of friction φ, with tan φ = μs. If we rotate the line of R around the normal, it sweeps a cone of friction: as long as the total reaction lies inside the cone, the body does not slip.
A body resting on a plane that is slowly tilted starts to slide when the slope angle reaches φ. This angle is the angle of repose. The same idea, with internal friction of grains replacing surface friction, explains why dry sand and aggregate stockpiles stand at a natural slope, an idea developed further in soil mechanics.
Derivation
- Draw the free body of a block of weight W on a horizontal surface with horizontal pull P. Equilibrium gives N = W and F = P.
- The block stays at rest while F ≤ μs N, that is while P ≤ μs W. At P = μs W, motion is impending.
- The total reaction R = √(N² + F²) makes angle β with the normal, tan β = F/N. At impending slip, tan β = μs, so β = φ = tan⁻¹ μs.
- Angle of repose: on a plane at angle θ, N = W cos θ and the force down the slope is W sin θ. Slip is impending when W sin θ = μs W cos θ, so tan θ = μs and θ = φ.
- Pull at angle α above the horizontal: N = W − P sin α and P cos α = μs N, giving P = μs W / (cos α + μs sin α). Differentiating the denominator and setting it to zero gives tan α = μs, so the smallest pull acts at α = φ and equals W sin φ.
Static, no slip: F ≤ μs NImpending slip: F = μs N; sliding: F = μk N (N)Angle of friction: tan φ = μsAngle of repose = φPull at angle α: P = μs W / (cos α + μs sin α); minimum P = W sin φ at α = φ
- Dry (Coulomb) friction between rigid surfaces; no lubrication or adhesion.
- μ is constant for a given pair of surfaces and condition; real values scatter and change with moisture, contamination and wear.
- Speeds are low enough that kinetic friction is independent of speed.
Codes and standards
Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.
- IS 800:2007 cl. 10.4.3 designs slip-resistant (friction-grip) bolted connections, with the slip resistance proportional to the slip factor μf (Table 20; capped at 0.55 by Amendment 1) times the bolt pretension. EN 1993-1-8 cl. 3.9 covers the same connection type, with slip factors given in EN 1090-2. Listed for comparison, not ranked.
Worked examples
Problem. A 500 N block rests on a level floor with μs = 0.4 and μk = 0.3. Find the friction force when a horizontal push of (a) 150 N and (b) 250 N is applied. In case (b), find the acceleration (g = 9.81 m/s²).
- N = 500 N, so the limiting static friction is 0.4 × 500 = 200 N.
- (a) 150 N < 200 N: no slip, and friction just balances the push: F = 150 N.
- (b) 250 N > 200 N: the block slides, so F = μk N = 0.3 × 500 = 150 N.
- Net force 250 − 150 = 100 N; mass 500/9.81 = 50.97 kg; a = 100/50.97 = 1.962 m/s².
Answer. (a) 150 N, no motion; (b) 150 N kinetic friction, a = 1.962 m/s²
Problem. A 2 kN crate of fittings is dragged across a concrete floor by a rope inclined 30° above the horizontal, μs = 0.5. Find the pull needed to start it moving, and the best rope angle with its pull.
- N = 2 000 − P sin 30°; impending slip: P cos 30° = 0.5 (2 000 − 0.5 P).
- P (0.8660 + 0.25) = 1 000, so P = 896.0 N.
- Best angle α = φ = tan⁻¹ 0.5 = 26.57°.
- Minimum pull = W sin φ = 2 000 × sin 26.57° = 894.4 N, only slightly less than at 30°.
Answer. 896.0 N at 30°; minimum 894.4 N at 26.57°
Step-by-step procedure
- Draw the free body with N normal and F along the surface, opposing the tendency to slide.
- Assume no slip and solve equilibrium for F and N.
- Compare F with μs N: if F ≤ μs N the assumption holds.
- If F > μs N, the body slides: set F = μk N and use F = m a if needed.
- For impending motion problems, set F = μs N from the start.
Site notes
- Coefficients of friction quoted in handbooks are averages; for safety-critical checks (sliding of walls, slip of bolted joints) use values from the governing code or tests, not general tables.
- Wet, oily or dusty surfaces can reduce friction sharply; never rely on friction alone to hold loads on a sloping truck bed or scaffold.
- Dragging with the rope slightly raised lifts some weight off the floor and reduces the pull, which is why the best angle is not zero.
- Setting F = μ N when the body is not on the point of slipping; friction is only as large as equilibrium needs.
- Taking N = W when other forces have vertical components.
- Drawing friction in the direction of the tendency to move instead of opposing it.
- Using μk to decide whether a body at rest will start moving.
- Thinking a larger contact area always gives more friction.
tan φ = μ. Typical dry values give φ of roughly 15° to 35°. If a calculation needs an angle of friction above 45° (μ > 1) for ordinary dry surfaces, re-check the data.
Summary
- Friction opposes relative sliding and grows up to F_max = μs N.
- Sliding friction F = μk N, with μk usually less than μs.
- tan φ = μs; the angle of repose equals φ.
- The best pulling angle is φ, giving P_min = W sin φ.
Practice questions
Tap a question to see the answer.
1Find the angle of friction for μs = 0.3.
φ = tan⁻¹ 0.3 = 16.70°.
2A body slips on a plane tilted to 22°. Find μs.
μs = tan 22° = 0.404.
3A 1 kN box on a floor with μs = 0.35 is pushed horizontally with 300 N. Does it move, and what is the friction force?
Limit 350 N > 300 N: no motion; F = 300 N.
4A 600 N block is pulled with a horizontal 200 N force, μs = 0.4, μk = 0.3. Does it slide, and what is the friction force?
Limit 240 N > 200 N, so it stays; F = 200 N.
5What is the smallest force that can start a 1 200 N block sliding on a level floor with μs = 0.75?
φ = 36.87°, P_min = 1 200 sin 36.87° = 720 N, applied 36.87° above the horizontal.
References
Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.
- F. P. Beer, E. R. Johnston, D. F. Mazurek, P. J. Cornwell, B. P. Self, Vector Mechanics for Engineers: Statics and Dynamics, McGraw Hill, 12th edition, 2019.
- R. C. Hibbeler, Engineering Mechanics: Statics, Pearson, 15th edition, 2022 (published 2021).
- J. L. Meriam, L. G. Kraige, J. N. Bolton, Engineering Mechanics: Statics, Wiley, 9th edition, 2018.
- S. Timoshenko, D. H. Young, J. V. Rao, S. Pati, Engineering Mechanics (in SI units), McGraw Hill Education (India), 5th edition, 2013.