Indiacon CivilSubscribe

Textbook › Engineering Mechanics › Chapter 3 › Lesson 3.2

3.2 Blocks on inclined planes

Engineering Mechanics Chapter 3: Friction Under review — not yet three-checked Author: Indiacon

Learning objectives

After this lesson you should be able to:

  • Find the force needed to hold, raise or lower a block on a rough inclined plane, for a force parallel to the plane, horizontal or at any angle.
  • Use the total-reaction (angle of friction) method as a quick alternative to resolving N and F.
  • Check sliding of blocks and walls against a required factor of safety.

Theory

Inclined planes are everywhere on site: ramps, sloping formwork, chutes, embankment faces and the bases of retaining walls under thrust. The block-on-incline problem is the template for all of them. Its weight is resolved into W sin θ down the slope and W cos θ normal to it. Without friction, any slope needs a holding force; with friction, slopes flatter than the angle of friction hold the block by themselves.

The direction of the friction force depends on what is about to happen. If the applied force is just enough to stop the block sliding down, friction acts up the slope and helps. If the force is about to push the block up, friction acts down the slope and resists. The force to raise is therefore always larger than the force to hold, and the difference grows with μ.

WPFNθImpending motion up the planeIndiacon original, not to scale
Figure 3.2: Block about to move up a rough incline: P up the slope, friction F down the slope, normal reaction N. Indiacon original, not to scale.

An efficient alternative is to replace N and F by the total reaction R, inclined at φ to the normal. For impending upward motion R leans back down the slope, at (θ + φ) to the vertical; for impending downward motion it leans the other way, at (θ − φ). The problem becomes a three-force problem (W, P and R), solved by a force triangle or the sine rule. This gives compact results such as P = W tan(θ + φ) for a horizontal push up the slope.

In design, friction under a base often provides the resistance to sliding. The sliding factor of safety is the frictional resistance divided by the horizontal force. Because only part of the dead load can be relied on, codes reduce the weight used in this check.

Derivation

  1. Force P parallel to the plane, impending upward motion: along the plane P − W sin θ − μ N = 0; normal N − W cos θ = 0. So P = W (sin θ + μ cos θ).
  2. Impending downward motion (P just holds the block): friction acts up the plane, so P = W (sin θ − μ cos θ). If this is negative, the block holds itself (θ < φ).
  3. With μ = tan φ: sin θ + tan φ cos θ = sin(θ + φ)/cos φ, so P_up = W sin(θ + φ)/cos φ.
  4. Horizontal push, impending upward motion: R is at (θ + φ) to the vertical, and the force triangle of W (vertical), P (horizontal) and R gives P = W tan(θ + φ). For holding: P = W tan(θ − φ).
  5. Force at angle β to the plane: P = W sin(θ + φ)/cos(β − φ), which is smallest when β = φ, giving P_min = W sin(θ + φ).
Formulas, symbols and SI units
  • Parallel push up: P = W (sin θ + μ cos θ); parallel hold: P = W (sin θ − μ cos θ)
  • Horizontal push up: P = W tan(θ + φ); horizontal hold: P = W tan(θ − φ)
  • Minimum force up the plane: P_min = W sin(θ + φ), at angle φ to the plane
  • Self-holding if θ ≤ φ
  • Sliding factor of safety: FS = μ N_reliable / H
Assumptions and limits
  • Dry friction with constant μ; block treated as a particle (no tipping).
  • Forces lie in the vertical plane containing the line of greatest slope.
  • Impending motion; for actual sliding use μk and F = m a.

Codes and standards

Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.

  • IS 456:2000 cl. 20.2 requires a factor of safety against sliding of not less than 1.4, counting only 0.9 times the characteristic dead load. EN 1997-1 (cl. 6.5.3) checks sliding of footings with partial factors instead of a single factor of safety. Listed for comparison, not ranked.

Worked examples

Example 1 (exam style)

Problem. A 1 000 N block rests on a 30° incline with μ = 0.25. Will it slide on its own? Find the force parallel to the plane needed (a) to stop it sliding down and (b) to push it up at constant (impending) speed.

  1. tan 30° = 0.577 > 0.25, so θ > φ (14.04°) and the block will slide unless held.
  2. (a) P = W (sin θ − μ cos θ) = 1 000 (0.5 − 0.25 × 0.8660) = 283.5 N.
  3. (b) P = W (sin θ + μ cos θ) = 1 000 (0.5 + 0.2165) = 716.5 N.
  4. The 433 N difference is twice the friction force μ W cos θ = 216.5 N.

Answer. It slides; 283.5 N to hold, 716.5 N to push up

Example 2 (site style)

Problem. A 1 kN bundle of shuttering on a 20° ramp is pushed up with a horizontal force by a worker using a pole. μ = 0.3. Find the horizontal force at impending motion.

  1. φ = tan⁻¹ 0.3 = 16.70°.
  2. For a horizontal push upward, P = W tan(θ + φ).
  3. P = 1 000 × tan(36.70°) = 745.4 N.
  4. Compare with a push parallel to the ramp: 1 000 (sin 20° + 0.3 cos 20°) = 624.0 N; pushing horizontally wastes effort pressing the load into the ramp.

Answer. 745.4 N horizontally (624.0 N if pushed parallel to the ramp)

Step-by-step procedure

  1. Draw the block with W, P, N and F; decide the direction of impending motion.
  2. Point F to oppose that motion.
  3. Resolve along and normal to the plane, or use the total reaction at φ.
  4. Solve for P; check the sign (a negative holding force means no force is needed).
  5. For sliding of bases, compute FS with the reliable normal force and compare with the code value.

Site notes

  • Ramps used for wheelbarrows and trolleys should be kept well below the angle at which loads start to slide or run back; anti-slip battens raise the effective friction.
  • Sloping formwork for inclined slabs and staircases develops a down-slope component of fresh concrete weight; props must resist it, not just the vertical load.
  • Retaining walls that fail the sliding check are often given a shear key below the base, which brings passive soil resistance into play.
Common mistakes
  • Pointing friction the wrong way for the motion considered.
  • Using N = W instead of W cos θ.
  • Using tan(θ + φ) for a force parallel to the plane (that formula is for a horizontal force).
  • Forgetting the 0.9 factor on dead load in a code sliding check.
  • Assuming the block slides whenever θ > 0.
Quick check

For a force along the slope: up = W(sin θ + μ cos θ), down-hold = W(sin θ − μ cos θ). Their average is W sin θ, the force needed without friction.

Summary

  • Friction helps when holding and resists when raising.
  • Parallel force: P = W(sin θ ± μ cos θ).
  • Horizontal force: P = W tan(θ ± φ).
  • Self-holding when θ ≤ φ; sliding checks use only the reliable dead load.

Practice questions

Tap a question to see the answer.

1Will a block stay on a 25° slope if μ = 0.5?

tan 25° = 0.466 < 0.5, so it stays.

2Find the parallel force to drag a 2 kN load up a 15° slope with μ = 0.4.

2 000 (0.2588 + 0.4 × 0.9659) = 1 290.4 N.

3Find the smallest force that can push a 1 000 N block up a 20° plane with μ = 0.3.

P_min = 1 000 sin(36.70°) = 597.6 N, at 16.70° to the plane.

4A wall weighs 150 kN per metre and resists 50 kN per metre of horizontal thrust by base friction with μ = 0.5. Check the IS 456 sliding requirement.

FS = 0.5 × 0.9 × 150 / 50 = 1.35 < 1.4, so it fails; a shear key or wider base is needed.

5What horizontal force just holds a 500 N block on a 35° plane with μ = 0.2?

φ = 11.31°; P = 500 tan(23.69°) = 219.4 N.

References

Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.

  • F. P. Beer, E. R. Johnston, D. F. Mazurek, P. J. Cornwell, B. P. Self, Vector Mechanics for Engineers: Statics and Dynamics, McGraw Hill, 12th edition, 2019.
  • R. C. Hibbeler, Engineering Mechanics: Statics, Pearson, 15th edition, 2022 (published 2021).
  • J. L. Meriam, L. G. Kraige, J. N. Bolton, Engineering Mechanics: Statics, Wiley, 9th edition, 2018.
  • S. Timoshenko, D. H. Young, J. V. Rao, S. Pati, Engineering Mechanics (in SI units), McGraw Hill Education (India), 5th edition, 2013.
Suggest a correction

If something on this page is wrong, tell the editor. Your message is sent privately and is not published.

Sent privately to the Indiacon editor; not published.