3.3 Ladders and wedges
After this lesson you should be able to:
- Find the limiting position of a ladder, or of a person on it, from friction at its ends.
- Analyse a wedge used to raise or position a heavy load, including the force to insert it and to withdraw it.
- Derive and apply the self-locking condition for a wedge.
Theory
A ladder leaning on a wall is a rigid body held by friction at the floor (and sometimes at the wall). Its weight and any load on it try to make the foot slide outward; friction at the foot resists. As a person climbs higher, the moment of their weight about the foot grows, the wall must push harder, and the foot friction must grow to match it. Slip occurs when that friction reaches μN.
With a smooth wall and a rough floor, the classical result for a uniform ladder alone is that the ladder slips if it is flatter than the angle given by tan θ = 1/(2μ), measured from the floor. Real ladder safety rules (a base set out about one quarter of the height, so roughly 75° to the floor) keep well inside this limit, because floor friction is unreliable.
A wedge is a simple machine: a small force driven horizontally produces a large force normally, used to lift beams, tighten formwork, set precast units, split stone and adjust bearings. A wedge problem has several contact faces with friction. The total reaction at each face is inclined at φ to the normal, opposing the relative motion at that face. Drawing the free bodies of the wedge and the load with these reactions turns the problem into force triangles.
A wedge that stays in place when the driving force is removed is self-locking. For a wedge with friction on both faces and the same angle of friction on each, self-locking requires the wedge angle α to be less than 2φ. Most site wedges are self-locking, which is why a wedge must be driven out rather than simply released.
Derivation
- Ladder of weight W1 and length L at angle θ to a rough floor, against a smooth wall, with a person of weight W2 at distance x up the ladder. Floor: N_f vertical and friction F horizontal; wall: N_w horizontal.
- ΣFy: N_f = W1 + W2. ΣFx: F = N_w. Moments about the foot: N_w L sin θ = W1 (L/2) cos θ + W2 x cos θ.
- Slip impends when F = μ N_f. Then N_w = μ (W1 + W2), and x = [μ (W1 + W2) L sin θ − W1 (L/2) cos θ] / (W2 cos θ).
- Ladder alone (W2 = 0): μ W1 L sin θ = W1 (L/2) cos θ, so tan θ = 1/(2μ) at the limit.
- Wedge of angle α on a rough floor, lifting a block held laterally by a smooth guide: the block's reaction from the wedge is at (α + φ) to the vertical, so R1 = W / cos(α + φ). The floor reaction on the wedge is at φ, with R2 cos φ = W. Horizontal balance of the wedge: P = W tan(α + φ) + W tan φ.
- Withdrawal reverses the friction: P_out = W tan(φ − α) + W tan φ. The wedge holds itself when P_out > 0, i.e. tan(α − φ) < tan φ, so α < 2φ.
Ladder, smooth wall, rough floor, limiting angle (ladder alone): tan θ = 1/(2μ)Ladder with person at x: N_w L sin θ = W1 (L/2) cos θ + W2 x cos θ, with N_w = μ (W1 + W2) at slipWedge insertion (one inclined face, smooth guide): P = W [tan(α + φ) + tan φ]Wedge withdrawal: P = W [tan(φ − α) + tan φ]; self-locking if α < 2φ
- Rigid ladder and wedge; dry friction with the same μ at the faces stated.
- For the ladder: smooth wall unless stated; uniform ladder with weight at mid-length.
- For the wedge: weight of the wedge neglected; the block cannot move sideways (smooth guide).
Codes and standards
Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.
- IS 3696 (Part 1):1987 covers safety for scaffolds and IS 3696 (Part 2):1991 safety for ladders in construction; they set practical rules (such as ladder pitch) rather than friction calculations. Comparable guidance elsewhere includes EN 131 for ladders. Listed for comparison, not ranked.
Worked examples
Problem. A uniform 6 m ladder weighing 250 N leans at 60° to the floor against a smooth wall. μ at the floor is 0.4. How far up the ladder can a 750 N person climb before it slips?
- N_f = 250 + 750 = 1 000 N; at slip F = N_w = 0.4 × 1 000 = 400 N.
- Moments about the foot: 400 × 6 sin 60° = 250 × 3 cos 60° + 750 x cos 60°.
- 2 078.5 = 375 + 375 x.
- x = (2 078.5 − 375) / 375 = 4.543 m along the ladder.
Answer. About 4.54 m up the 6 m ladder
Problem. A steel wedge with a 10° face is driven under the end of a beam to lift it. The beam end bears 10 kN on the wedge and is held sideways by a smooth guide. μ = 0.25 on both wedge faces. Find the force to drive the wedge in, the force to pull it out, and whether it is self-locking.
- φ = tan⁻¹ 0.25 = 14.04°.
- Insertion: P = 10 [tan(24.04°) + 0.25] = 10 (0.4460 + 0.25) = 6.960 kN.
- Withdrawal: P = 10 [tan(4.04°) + 0.25] = 10 (0.0706 + 0.25) = 3.206 kN, a pull.
- α = 10° < 2φ = 28.07°, so the wedge is self-locking and stays in place when released.
Answer. 6.960 kN to drive in; 3.206 kN to pull out; self-locking
Step-by-step procedure
- Draw a free body of each part (ladder; or wedge and load separately).
- At each rough face, draw N and F with F opposing the impending relative motion, or a single R at φ to the normal.
- Write equilibrium; for wedges, solve the load first, then the wedge.
- Set F = μ N at the faces where slip impends.
- Check self-locking for wedges by reversing the motion.
Site notes
- Set ladders at about 1 out for every 4 up, on firm level ground, tied or footed at the top; the calculation shows why the foot slips first.
- Hardwood folding wedges under props and formwork are self-locking; always tap them out, never kick a prop expecting the wedges to release.
- When jacking with wedges, insert packers as the load rises so the load never rests on the wedge alone.
- Drawing friction at the foot of a ladder pointing outward instead of towards the wall.
- Forgetting that wall friction, if present, acts upward on the ladder.
- Using the wedge angle instead of (α + φ) for the reaction direction.
- Ignoring friction on the floor face of the wedge.
- Assuming every wedge needs a holding force.
Wedge self-locking: α < 2φ. With μ = 0.25 (φ ≈ 14°), any wedge flatter than about 28° stays put. With a smooth wall, a lone ladder is safe if tan θ ≥ 1/(2μ).
Summary
- Ladders slip at the foot when floor friction reaches μN.
- Smooth wall, rough floor, ladder alone: tan θ_limit = 1/(2μ).
- Use total reactions at φ for wedges; P_in = W[tan(α + φ) + tan φ].
- Self-locking when α < 2φ.
Practice questions
Tap a question to see the answer.
1Find the flattest safe angle for a uniform ladder alone with μ = 0.4 at the floor and a smooth wall.
tan θ = 1/(2 × 0.4) = 1.25, so θ = 51.34° to the floor.
2In Example 1, what happens if μ = 0.5?
N_w = 500 N; 500 × 5.196 = 2 598.1 = 375 + 375 x, so x = 5.93 m: the person can climb almost to the top.
3A wedge has α = 8° and μ = 0.2 on both faces. Is it self-locking?
φ = 11.31°; 2φ = 22.62° > 8°, so yes.
4With α = 15° and μ = 0.2 on both faces, find the force to drive the wedge under a 5 kN load (smooth guide).
P = 5 [tan(26.31°) + 0.2] = 5 (0.4944 + 0.2) = 3.472 kN.
5Why does a steeper wedge need a larger driving force but give less lift per stroke?
A larger α raises tan(α + φ), increasing the force; the lift per unit horizontal travel is tan α, so a flatter wedge gives more mechanical advantage but smaller lift per stroke.
References
Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.
- F. P. Beer, E. R. Johnston, D. F. Mazurek, P. J. Cornwell, B. P. Self, Vector Mechanics for Engineers: Statics and Dynamics, McGraw Hill, 12th edition, 2019.
- R. C. Hibbeler, Engineering Mechanics: Statics, Pearson, 15th edition, 2022 (published 2021).
- J. L. Meriam, L. G. Kraige, J. N. Bolton, Engineering Mechanics: Statics, Wiley, 9th edition, 2018.
- S. Timoshenko, D. H. Young, J. V. Rao, S. Pati, Engineering Mechanics (in SI units), McGraw Hill Education (India), 5th edition, 2013.