3.4 Screw jack
After this lesson you should be able to:
- Model a square-threaded screw as a wedge wrapped round a cylinder and derive the effort and torque to raise and lower a load.
- Calculate the efficiency of a screw jack, including collar friction, and state the self-locking condition.
- Show why a self-locking screw has an efficiency below 50 per cent.
Theory
A screw jack lifts a heavy load by turning a threaded spindle in a nut. If one turn of the thread is unrolled, it becomes an inclined plane: the rise is the lead l (the axial advance per turn) and the run is the mean circumference π d. The helix angle α satisfies tan α = l / (π d). Turning the screw is like pushing the load up this inclined plane with a horizontal force applied at the mean radius.
For a single-start thread the lead equals the pitch p; for a multi-start thread with n starts, l = n p. A larger lead lifts faster but needs more torque and is less likely to hold the load by itself. With friction on the thread, the force at the mean radius to raise the load is P = W tan(α + φ), exactly the horizontal-push result for an inclined plane. The torque on the screw is P times the mean radius, and the effort at the end of a handle of length L is that torque divided by L.
Many jacks also have a rotating collar or thrust face under the load. Friction there adds a second torque, roughly μc W rc, where rc is the mean collar radius. In heavy jacks this collar torque can be as large as the thread torque, which is why ball thrust bearings are often fitted.
Efficiency is the useful work (W times lift) divided by the work input (torque times angle turned) over one turn. If the friction angle is larger than the helix angle, the load cannot drive the screw backwards: the jack is self-locking and holds the load without a brake. The price is low efficiency: a self-locking square-threaded screw always has an efficiency below one half.
Derivation
- Unroll one turn of the thread: a plane inclined at α with tan α = l / (π d), where d is the mean diameter.
- The load W rests on this plane; a horizontal force P at the mean radius drives it up. From lesson 3.2, P = W tan(α + φ), with tan φ = μ.
- Torque to raise (thread only): T = P d/2 = W (d/2) tan(α + φ). Effort at a handle of length L: E = T / L.
- To lower, friction reverses: T_lower = W (d/2) tan(φ − α). It is positive (a torque is needed to lower) when φ > α: self-locking.
- Without friction (φ = 0), T0 = W (d/2) tan α. Efficiency η = T0 / T = tan α / tan(α + φ). Including collar torque Tc = μc W rc: η = W l / (2π (T + Tc)).
- At the self-locking limit φ = α: η = tan α / tan 2α = (1 − tan² α)/2 < 1/2. So any self-locking square-threaded screw has η < 50 per cent.
- The thread efficiency is greatest when α = 45° − φ/2, giving η_max = (1 − sin φ)/(1 + sin φ).
tan α = l / (π d); l = n p for an n-start threadTorque to raise: T = W (d/2) tan(α + φ) (N·m when W in N, d in m)Torque to lower: T = W (d/2) tan(φ − α); self-locking if φ > αCollar torque: Tc = μc W rcEfficiency: η = tan α / tan(α + φ) (thread only); η = W l / (2π (T + Tc)) with collar
- Square thread; for V or trapezoidal threads the normal force is larger and μ is replaced by μ / cos β (β the half thread angle measured in the axial plane), which is not covered here.
- Load acts at the mean thread radius; friction coefficient constant.
- Static (slow) operation; collar friction modelled at a single mean radius.
Codes and standards
Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.
- No design code governs the mechanics of this lesson. Real jacks are used within the manufacturer's rated capacity and the site's lifting and temporary works rules; bridge bearing replacement jacking is planned under the bridge owner's specifications.
Worked examples
Problem. A screw jack has a single-start square thread of mean diameter 50 mm and pitch 10 mm; μ = 0.12. It lifts 20 kN with a 400 mm handle; collar friction is negligible. Find the effort, the efficiency, and the torque needed to lower the load.
- tan α = 10 / (π × 50) = 0.06366, so α = 3.643°; φ = tan⁻¹ 0.12 = 6.843°.
- T = 20 000 × 0.025 × tan(10.485°) = 20 000 × 0.025 × 0.18508 = 92.54 N·m.
- Effort E = 92.54 / 0.400 = 231.3 N.
- η = 0.06366 / 0.18508 = 0.344, i.e. 34.4 per cent (below 50 per cent, as expected for a self-locking screw).
- Lowering torque = 20 000 × 0.025 × tan(3.200°) = 27.96 N·m, positive, so the jack is self-locking.
Answer. Effort 231.3 N; η = 34.4 %; 27.96 N·m to lower (self-locking)
Problem. A heavy screw jack lifts one end of a girder by 150 kN for bearing inspection. Mean thread diameter 80 mm, single-start pitch 12 mm, μ = 0.15 on the thread; the load sits on a collar of mean radius 40 mm with μc = 0.15. Find the total torque, the effort on a 0.6 m bar and the overall efficiency.
- tan α = 12 / (π × 80) = 0.04775, α = 2.734°; φ = 8.531°.
- Thread torque T = 150 × 0.040 × tan(11.265°) = 1.195 kN·m.
- Collar torque Tc = 0.15 × 150 × 0.040 = 0.900 kN·m; total 2.095 kN·m.
- Effort on a 0.6 m bar = 2.095 / 0.6 = 3.49 kN, far beyond one person, which is why hydraulic jacks are used for such loads.
- η = 150 × 0.012 / (2π × 2.095) = 0.137, i.e. 13.7 per cent.
Answer. 2.095 kN·m; 3.49 kN effort; η = 13.7 %
Step-by-step procedure
- Find the lead (l = n p) and helix angle (tan α = l / π d).
- Find φ from μ and check self-locking (φ > α).
- Compute the thread torque to raise, add collar torque if present.
- Divide by the handle length for effort; compute efficiency from work in and out.
- For lowering, use tan(φ − α); a negative value means the load will run down by itself.
Site notes
- Screw jacks and adjustable props are self-locking by design; do not lubricate the thread with anything not approved by the maker, since lower friction reduces the margin against running down.
- When a long bar is needed to turn a jack, the load is close to the jack's limit; stop and check the rating.
- Always pack under a jacked load as it rises; the thread holds the load, but a tilted or overloaded jack can fail suddenly.
- Using the outer diameter instead of the mean diameter in tan α.
- Using the pitch instead of the lead for a multi-start thread.
- Forgetting collar friction in heavy jacks.
- Calling a screw with η above 50 per cent self-locking.
- Mixing mm and m in the torque calculation.
Self-locking screw ⇒ η < 50 %. If your calculation gives a self-locking jack with efficiency above one half, check the angles.
Summary
- A screw thread is an inclined plane wrapped round a cylinder; tan α = l / (π d).
- Raise: T = W (d/2) tan(α + φ); lower: T = W (d/2) tan(φ − α).
- Self-locking when φ > α; efficiency then below 50 %.
- Collar friction adds μc W rc and can be large.
Practice questions
Tap a question to see the answer.
1A double-start thread has pitch 6 mm and mean diameter 40 mm. Find the lead and helix angle.
l = 12 mm; tan α = 12 / (π × 40) = 0.0955, α = 5.455°.
2For μ = 0.1, what helix angle gives maximum thread efficiency, and what is it?
α = 45° − 5.71°/2 = 42.15°; η_max = (1 − sin 5.71°)/(1 + sin 5.71°) = 0.819.
3A screw has α = 4° and μ = 0.05. Is it self-locking?
φ = 2.86° < 4°, so no: the load can run it down.
4In Example 1, what effort would be needed with a 600 mm handle?
92.54 / 0.6 = 154.2 N.
5Find the thread efficiency for α = 5° and φ = 7°.
η = tan 5° / tan 12° = 0.0875 / 0.2126 = 0.411 (41.1 %).
References
Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.
- F. P. Beer, E. R. Johnston, D. F. Mazurek, P. J. Cornwell, B. P. Self, Vector Mechanics for Engineers: Statics and Dynamics, McGraw Hill, 12th edition, 2019.
- R. C. Hibbeler, Engineering Mechanics: Statics, Pearson, 15th edition, 2022 (published 2021).
- J. L. Meriam, L. G. Kraige, J. N. Bolton, Engineering Mechanics: Statics, Wiley, 9th edition, 2018.
- S. Timoshenko, D. H. Young, J. V. Rao, S. Pati, Engineering Mechanics (in SI units), McGraw Hill Education (India), 5th edition, 2013.