Indiacon CivilSubscribe

Textbook › Engineering Mechanics › Chapter 3 › Lesson 3.5

3.5 Belt and rope friction

Engineering Mechanics Chapter 3: Friction Under review — not yet three-checked Author: Indiacon

Learning objectives

After this lesson you should be able to:

  • Derive the capstan (belt friction) equation T1/T2 = e^(μθ).
  • Find the holding force for a rope wrapped round a bollard, post or drum.
  • Calculate the power transmitted by a flat belt drive and the effect of wrap angle.

Theory

When a rope or belt is wrapped round a fixed cylinder and pulled at both ends, friction along the contact lets a small force on one end hold a large force on the other. The tension rises exponentially along the contact. This is why a few turns of rope round a bollard can hold a ship, and why a winch drum needs only a light pull on the tail rope.

The result, known as the capstan or Euler–Eytelwein equation, is T1 / T2 = e^(μθ), where T1 is the tension on the tight side (the side the rope is about to slip towards), T2 the tension on the slack side, μ the coefficient of friction and θ the angle of wrap in radians. It does not depend on the radius of the drum. Each extra turn multiplies the ratio by e^(2πμ); with μ = 0.3 that factor is about 6.6.

T1T2θ = πT1 / T2 = e^(μθ)Indiacon original, not to scale
Figure 3.5: Rope over a fixed drum: the tight-side tension T1 exceeds the slack-side tension T2 by the factor e^(μθ). Indiacon original, not to scale.

In a belt drive the same law limits how much torque a pulley can transmit before the belt slips. The power transmitted is the difference in tensions times the belt speed: P = (T1 − T2) v. For a given maximum belt tension, more wrap angle or more friction lets the drive carry more power. V-belts wedge into their grooves, which increases the normal force; their effective coefficient is μ / sin(β/2), where β is the groove angle.

At high belt speeds, the belt's own mass creates centrifugal tension that reduces the grip; it is ignored in the basic analysis here and treated in machine design.

Derivation

  1. Take a small element of rope subtending angle dθ, with tension T on one side and T + dT on the other, normal force dN from the drum and friction μ dN at impending slip.
  2. Radial balance: dN = (T + dT) sin(dθ/2) + T sin(dθ/2) ≈ T dθ, neglecting second-order terms.
  3. Tangential balance: (T + dT) cos(dθ/2) − T cos(dθ/2) = μ dN, so dT = μ T dθ.
  4. Separate and integrate from the slack side (T2, θ = 0) to the tight side (T1, θ): ∫ dT/T = μ ∫ dθ, so ln(T1/T2) = μθ.
  5. Hence T1/T2 = e^(μθ). The radius cancels out, so the ratio depends only on μ and the total angle of wrap.
Formulas, symbols and SI units
  • T1 / T2 = e^(μθ), θ in radians (1 turn = 2π rad)
  • Belt power: P = (T1 − T2) v (W when T in N and v in m/s)
  • Belt speed: v = π D N / 60 (D in m, N in rev/min)
  • V-belt or rope in groove: T1 / T2 = e^(μθ / sin(β/2))
Assumptions and limits
  • Flat, flexible, inextensible rope or belt; no bending stiffness.
  • Uniform μ over the contact; impending (or steady) slip over the whole arc.
  • Centrifugal effects neglected; angle θ in radians.

Codes and standards

Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.

  • No design code governs this lesson. Wire rope and winch arrangements on site follow the lifting equipment rules and the manufacturer's data; mooring bollards in ports are designed to port design standards, which set loads rather than this equation.

Worked examples

Example 1 (exam style)

Problem. A rope is wound 2.5 turns round a fixed bollard, μ = 0.3. What pull on the free end holds a 10 kN load on the other end?

  1. θ = 2.5 × 2π = 5π = 15.708 rad.
  2. e^(μθ) = e^(0.3 × 15.708) = e^(4.712) = 111.3.
  3. T2 = T1 / 111.3 = 10 000 / 111.3 = 89.8 N.
  4. A pull under 90 N holds 10 kN: the reason wraps round a post are used to control loads.

Answer. About 89.8 N

Example 2 (site style)

Problem. A flat belt drives a concrete mixer from a pulley of diameter 0.5 m at 300 rev/min. The angle of lap is 165°, μ = 0.3 and the maximum safe belt tension is 2.5 kN. Find the slack-side tension and the greatest power the belt can transmit.

  1. θ = 165° = 2.880 rad; e^(0.3 × 2.880) = 2.372.
  2. T2 = 2 500 / 2.372 = 1 053.7 N.
  3. v = π × 0.5 × 300 / 60 = 7.854 m/s.
  4. P = (2 500 − 1 053.7) × 7.854 = 11 359 W, about 11.4 kW.

Answer. T2 = 1 053.7 N; about 11.4 kW

Step-by-step procedure

  1. Identify the tight side (towards which slip would occur) and the slack side.
  2. Convert the wrap angle to radians.
  3. Apply T1 = T2 e^(μθ) (or with μ / sin(β/2) for grooves).
  4. For drives, find v from diameter and speed, then P = (T1 − T2) v.
  5. Check that the tight-side tension is within the belt or rope capacity.

Site notes

  • Taking one extra turn round a bollard or post multiplies holding power several times; it is a safer way to control a load than relying on grip.
  • Belts slip first on the smaller pulley because it has the smaller wrap; idlers that increase wrap reduce slip.
  • Wet or greasy ropes have lower μ; allow for this when lowering loads by hand round a post.
Common mistakes
  • Using degrees instead of radians in the exponent.
  • Swapping T1 and T2, which inverts the result.
  • Including the drum radius in the ratio.
  • Adding the tensions instead of subtracting them to find transmitted force.
  • Forgetting that the smaller pulley governs slip in a drive.
Quick check

Each full turn multiplies the tension ratio by e^(2πμ): about 3.5 for μ = 0.2, 6.6 for μ = 0.3 and 12.3 for μ = 0.4.

Summary

  • T1 / T2 = e^(μθ), independent of radius.
  • Tension grows exponentially with wrap angle.
  • Belt power P = (T1 − T2) v.
  • Grooved belts grip better: use μ / sin(β/2).

Practice questions

Tap a question to see the answer.

1Find T1/T2 for μ = 0.25 and a half-turn wrap.

e^(0.25π) = 2.193.

2A rope makes one full turn round a post with μ = 0.2. What pull holds 1 kN?

1 000 / e^(0.4π) = 1 000 / 3.514 = 284.6 N.

3How many turns with μ = 0.3 are needed for a ratio of at least 100?

θ = ln 100 / 0.3 = 15.35 rad = 2.44 turns, so 2.5 turns.

4A belt has T1 = 1.8 kN and T2 = 0.6 kN at 10 m/s. Find the power.

(1 800 − 600) × 10 = 12 000 W = 12 kW.

5For a V-belt with groove angle 40° and μ = 0.25, what is the effective coefficient?

0.25 / sin 20° = 0.731.

References

Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.

  • F. P. Beer, E. R. Johnston, D. F. Mazurek, P. J. Cornwell, B. P. Self, Vector Mechanics for Engineers: Statics and Dynamics, McGraw Hill, 12th edition, 2019.
  • R. C. Hibbeler, Engineering Mechanics: Statics, Pearson, 15th edition, 2022 (published 2021).
  • J. L. Meriam, L. G. Kraige, J. N. Bolton, Engineering Mechanics: Statics, Wiley, 9th edition, 2018.
  • S. Timoshenko, D. H. Young, J. V. Rao, S. Pati, Engineering Mechanics (in SI units), McGraw Hill Education (India), 5th edition, 2013.
Suggest a correction

If something on this page is wrong, tell the editor. Your message is sent privately and is not published.

Sent privately to the Indiacon editor; not published.