5.1 Influence lines for determinate beams
After this lesson you should be able to:
- Define an influence line and explain how it differs from a shear force or bending moment diagram.
- Construct influence lines for the reactions, the shear and the bending moment at a section of simply supported, overhanging, cantilever and compound beams directly from statics.
- Use influence lines to find the value of a reaction, shear or moment caused by point loads (load times ordinate) and by uniformly distributed loads (intensity times area).
Theory
A bending moment diagram shows the moment at every section for one fixed position of the load. Bridges, crane girders and gantry beams carry loads that move, so the designer asks the opposite question: for one particular quantity, such as the reaction at A or the moment at a section C, how does its value change as a load travels along the span? The graph that answers this, drawn for a single unit load, is the influence line of that quantity. Its ordinate at a point x is the value of the quantity when the unit load stands at x. Sign convention for this chapter: the moving unit load acts downward; reactions are positive upward; the shear at a section is positive when the resultant of the forces on the part to its left acts upward; a sagging bending moment is positive and a hogging one negative; truss member forces are positive in tension; x is measured from the left support.
For a statically determinate beam every reaction and internal force is a linear function of the load position within each segment, so influence lines are made of straight lines. For a simply supported beam of span L, a unit load at x gives R_A = 1 − x/L and R_B = x/L. Cutting the beam at a section C, a distance a from A and b from B, and using the free body on the side without the load gives the shear and moment at C. The shear line is −x/L while the load is left of C and 1 − x/L when it is right of C, so it jumps by exactly one at the section. The moment line is a triangle with its peak ab/L under the section.
Overhangs extend the straight lines beyond the supports, so a load on an overhang can produce negative reactions (uplift) and hogging moments within the span. A cantilever has the simplest lines: the fixed-end shear is 1 wherever the load stands, and the fixed-end moment is −x, growing with the lever arm. In a compound beam with an internal hinge (a suspended span carried on a cantilever), the line for a quantity in the supporting part has a kink at the hinge and falls to zero at the far support of the suspended span, while a quantity in the suspended span has no influence from loads on the supporting part.
Once the line is drawn, any loading is handled by superposition. A point load P at a point with ordinate y contributes P y; a uniformly distributed load w over a length contributes w times the area under the line over that length, with areas below the axis counted negative. The line also shows at a glance where to put a live load: over the positive part for the greatest positive value, over the negative part for the greatest negative value. This is the basis of every bridge live-load calculation.
Derivation
- Place a unit load at a distance x from A on a simply supported beam AB of span L.
- Moments about B: R_A L − 1(L − x) = 0, so R_A = 1 − x/L; vertical equilibrium gives R_B = x/L.
- Section C at distance a from A (b = L − a). For x < a, take the right-hand free body (no load on it): shear V_C = −R_B = −x/L and moment M_C = R_B b = x b/L.
- For x > a, take the left-hand free body (no load on it): V_C = R_A = 1 − x/L and M_C = R_A a = a(L − x)/L.
- The two moment expressions are equal at x = a with value ab/L, the peak; the two shear expressions differ by exactly 1 at x = a, the jump.
- For loads P_i at ordinates y_i and a uniform load w over a region with influence area A_w, the quantity is Σ P_i y_i + w A_w, by superposition of the unit-load results.
Simply supported beam: R_A = 1 − x/L, R_B = x/L (dimensionless; kN per kN of load)Shear at C (distance a from A): V_C = −x/L for x < a; V_C = 1 − x/L for x > a; jump of 1 at CMoment at C: M_C = x b/L for x ≤ a; M_C = a(L − x)/L for x ≥ a; peak ab/L (m, i.e. kN m per kN)Cantilever fixed at A: R_A = 1; M_A = −x (hogging)Effect of point loads: Σ P_i y_i (kN or kN m)Effect of a uniform load: w × area under the influence line over the loaded length (w in kN/m)
- Linear elastic behaviour and small deflections, so superposition holds and the geometry does not change with the load.
- The beam is statically determinate, so every influence line is made of straight segments.
- Loads act vertically and are applied directly to the beam (indirect loading through cross girders is treated in lesson 5.4).
- The influence line describes one quantity at one fixed section or support; it is not a bending moment diagram.
- Limits: dynamic effects of moving vehicles, braking and impact are not included; they are added separately as specified in the relevant bridge loading code.
Codes and standards
Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.
- Influence lines are a result of statics; no design code governs the mechanics of this lesson, and no Indian Standard clause is cited here.
- Indian, European and American practice, side by side and not ranked, each define standard road vehicles, railway trains and uniform lane loads for bridge design; in India these come from the Indian Roads Congress bridge loading code for road bridges and the railway bridge rules for railway bridges. They are placed on influence lines exactly as shown in this chapter; their axle loads, spacings and impact allowances are not reproduced here.
Worked examples
Problem. A simply supported beam AB has a span of 12 m. Section C is 4 m from A. Draw the influence lines for R_A, the shear at C and the moment at C, and use them to find the shear and moment at C under a 60 kN point load 6 m from A together with a uniform load of 10 kN/m over the whole span.
- R_A line: 1 at A falling to 0 at B; at x = 6 m it is 0.5.
- Shear at C: −x/12 left of C (−1/3 just left of C), 1 − x/12 right of C (+2/3 just right of C).
- Moment at C: triangle with peak ab/L = 4 × 8/12 = 2.667 m at C; at x = 6 m the ordinate is a(L − x)/L = 4 × 6/12 = 2.0 m.
- Moment: point load 60 × 2.0 = 120 kN m; uniform load 10 × (½ × 12 × 2.667) = 10 × 16.0 = 160 kN m; total M_C = 280 kN m.
- Shear: point load 60 × 0.5 = 30 kN; uniform load 10 × (½ × 8 × 2/3 − ½ × 4 × 1/3) = 10 × 2.0 = 20 kN; total V_C = 50 kN.
- Check by statics: R_A = 30 + 60 = 90 kN; M_C = 90 × 4 − 10 × 4²/2 = 280 kN m; V_C = 90 − 40 = 50 kN.
Answer. M_C = 280 kN m (sagging), V_C = 50 kN
Problem. A beam rests on supports A (x = 0) and B (x = 8 m) and overhangs to a free end C at x = 10 m. A single load of 50 kN can stand anywhere on the beam. Find the greatest reaction at B, the greatest uplift at A, and the greatest sagging and hogging moments at D, the middle of AB.
- R_B line: x/8, reaching 1.25 at the tip C; R_A line: 1 − x/8, reaching −0.25 at C.
- Greatest R_B: load at C, 50 × 1.25 = 62.5 kN. Greatest uplift at A: load at C, 50 × (−0.25) = −12.5 kN, so A must be able to hold the beam down with 12.5 kN.
- Moment at D (a = b = 4 m): peak 4 × 4/8 = 2.0 m at D; beyond B the line continues as 4(8 − x)/8, giving −1.0 m at C.
- Greatest sagging moment at D: load at D, 50 × 2.0 = 100 kN m. Greatest hogging moment at D: load at C, 50 × (−1.0) = −50 kN m.
- Check the hogging case by statics: load at C gives R_A = −12.5 kN, so M_D = −12.5 × 4 = −50 kN m.
Answer. R_B max 62.5 kN; uplift at A 12.5 kN; M_D from +100 to −50 kN m
Problem. A cantilever AB, fixed at A and 4 m long, carries at its tip a hinge B, from which a suspended span BC of 6 m runs to a roller at C (x = 10 m). Draw the influence lines for R_C and for the fixed-end moment M_A, and find M_A and the vertical reaction at A under a uniform load of 15 kN/m over the whole length.
- R_C: zero for loads on AB (the hinge passes nothing back to C from the cantilever); (x − 4)/6 for loads on BC, rising to 1 at C.
- M_A for loads on AB: −x (hogging), reaching −4 at B. For loads on BC the hinge force is (10 − x)/6, so M_A = −4(10 − x)/6, falling from −4 at B to 0 at C.
- Area under the M_A line: −(½ × 4 × 4) − (½ × 6 × 4) = −8 − 12 = −20 m²; M_A = 15 × (−20) = −300 kN m.
- Vertical reaction at A: its line is 1 on AB and (10 − x)/6 on BC; area 4 + ½ × 6 × 1 = 7 m; R_A = 15 × 7 = 105 kN.
- Check by statics: the suspended span carries 90 kN, half of it (45 kN) at the hinge; M_A = −(60 × 2 + 45 × 4) = −300 kN m and R_A = 60 + 45 = 105 kN.
Answer. M_A = −300 kN m (hogging), R_A = 105 kN
Step-by-step procedure
- Choose the quantity and its location (a reaction, or the shear or moment at a named section).
- Place a unit load at a general position x; for each segment, write the quantity from the free body that does not carry the load.
- Plot the straight segments, mark the key ordinates (supports, section, hinges, ends) and check the jump of 1 in a shear line and the kink at a hinge.
- Apply the loads: Σ P y for point loads and w × area for uniform loads, taking signs from the line.
- For live loads, load only the region of the line with the sign you are looking for; check one case by direct statics.
Site notes
- Bridge girders, gantry girders in workshops and crane runway beams are designed with influence lines because the worst position of the load is different for every section and every quantity.
- Overhangs and cantilevered spans can lift off their far supports under a load on the tip; bearings and hold-down bolts must be designed for this uplift, and erection loads on overhangs need the same check.
- In suspended-span (cantilever-and-hinge) bridges, the hinge and its bearings are critical details; the influence lines show that loads on the suspended span reach the anchor span only through the hinge.
- A quick influence-line sketch on site helps decide where a heavy crane or a loaded truck may safely stand on an existing slab or deck.
- Treating an influence line as a bending moment diagram; its ordinate at x is the value at the fixed section when the load stands at x.
- Missing the jump of 1 in the shear line at the section, or putting it on the wrong side.
- Stopping the lines at the supports instead of extending them over an overhang.
- Adding areas without signs, so negative parts of the line are counted as positive.
- Forgetting that a load on the supporting cantilever has no effect on the reaction at the far end of a suspended span.
The moment influence line of a simply supported beam is a triangle of height ab/L, so a uniform load over the whole span gives M = w × ½ L × ab/L = w a b/2; at midspan this is wL²/8.
Summary
- An influence line gives the value of one quantity as a unit load moves across the structure.
- For determinate beams the lines are straight: R_A = 1 − x/L, a shear line with a jump of 1, and a moment triangle of height ab/L.
- Point loads contribute P × ordinate; uniform loads contribute w × area.
- Overhangs, cantilevers and hinges change the lines in predictable ways: extensions, constant ordinates and kinks.
- Live loads go on the part of the line with the sign being maximised.
Practice questions
Tap a question to see the answer.
1A simply supported beam of span 10 m has a section 4 m from A. Find the peak ordinate of the moment influence line at that section and the moment there under an 80 kN load placed at the section.
Peak ab/L = 4 × 6/10 = 2.4 m; moment 80 × 2.4 = 192 kN m.
2For the same beam, find the moment at the section under 12 kN/m over the whole span, using the influence line.
Area ½ × 10 × 2.4 = 12 m²; M = 12 × 12 = 144 kN m (statics: 60 × 4 − 12 × 4²/2 = 144 kN m).
3Give the ordinates of the shear influence line at midspan of a simply supported beam, and the greatest shear there under a single 60 kN load.
−0.5 just left and +0.5 just right of midspan; greatest shear 60 × 0.5 = 30 kN (either sign).
4For the overhanging beam of Example 2, find R_A and R_B when 10 kN/m acts on the overhang BC only.
R_A = 10 × ½ × 2 × (−0.25) = −2.5 kN (hold-down); R_B = 10 × ½ × (1 + 1.25) × 2 = 22.5 kN.
5A cantilever 3 m long is fixed at A. Using the influence line for M_A, find M_A under 25 kN at the tip and under 10 kN/m over the whole length.
M_A line is −x: 25 kN at the tip gives −75 kN m; the uniform load gives 10 × (−½ × 3 × 3) = −45 kN m.
6For the compound beam of Example 3, find R_C and M_A when a 100 kN load stands at the middle of the suspended span (x = 7 m).
R_C = (7 − 4)/6 × 100 = 50 kN; M_A = −4 × (10 − 7)/6 × 100 = −200 kN m.
References
Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.
- R. C. Hibbeler, Structural Analysis, Pearson, 10th edition, 2018.
- C. S. Reddy, Basic Structural Analysis, Tata McGraw Hill (now McGraw Hill Education (India)), 3rd edition, 2011.
- D. Menon, Structural Analysis, Narosa Publishing House, 2nd edition.
- B. J. Goodno, J. M. Gere, Mechanics of Materials, Cengage Learning, 9th edition, 2018.