Indiacon CivilSubscribe

Textbook › Structural Analysis › Chapter 5 › Lesson 5.4

5.4 Influence lines for trusses

Structural Analysis Chapter 5: Influence lines and moving loads Under review — not yet three-checked Author: Indiacon

Learning objectives

After this lesson you should be able to:

  • Explain how deck loads reach a truss through stringers and cross girders at the panel points, and why truss influence lines are straight between panel points.
  • Draw influence lines for chord, diagonal and vertical members of a parallel-chord truss from the moment and panel-shear lines of an equivalent beam, using the method of sections.
  • Find the greatest tension and compression in truss members under dead load plus a moving load, and identify members whose force can reverse.

Theory

In a truss bridge the deck does not rest on the truss members directly. The deck slab sits on longitudinal stringers, the stringers rest on cross girders, and the cross girders frame into the truss only at the panel points (the joints of the loaded chord). Each stringer acts as a simple beam between cross girders, so a load between two panel points reaches the truss as two panel-point loads shared in proportion to its distance from each. As a result, every truss influence line is a straight line between adjacent panel points, even where the equivalent beam line would have a peak. Sign convention for this chapter: the moving unit load acts downward; reactions are positive upward; the shear at a section is positive when the resultant of the forces on the part to its left acts upward; a sagging bending moment is positive and a hogging one negative; truss member forces are positive in tension; x is measured from the left support.

For a parallel-chord truss of depth h, a section cutting a top chord, a bottom chord and one diagonal gives each chord force from one moment equation. Taking moments about the joint where the other two cut members meet, the chord force equals the beam moment at that joint divided by h: tension in the bottom chord, compression in the top chord. So the influence line of a chord member is the moment influence line of the equivalent simple beam at the moment centre, divided by h.

Truss influence line: diagonal U2L3U2L3L2−0.471+0.707Indiacon original, not to scale; loads at bottom panel points
Figure 5.4: Influence line for a diagonal of a through Pratt truss: negative for loads to the left, positive for loads to the right, and a straight line across its own panel because loads arrive through stringers and cross girders. Indiacon original, not to scale.

The diagonal in the cut panel carries the panel shear. With θ the angle of the diagonal to the horizontal, the force is the panel shear divided by sin θ, with a sign fixed by the direction of the diagonal. The panel-shear line is the beam shear line (−x/L to the left, 1 − x/L to the right), except that across the loaded panel it is a straight line joining the two panel-point ordinates, because of the stringer action. That straight line crosses zero inside the panel, so loads on one side of that point produce tension in the diagonal and loads on the other side produce compression.

Verticals follow from joint equilibrium. In a Pratt truss loaded at the bottom chord (a through truss), a vertical whose top joint carries no load balances the vertical component of the diagonal meeting it there, so its line is minus the panel shear of that diagonal's panel. In a deck truss loaded at the top chord, the same vertical also carries the panel load at its top joint, so its influence line changes; the loaded chord must always be identified first. Members whose line has both positive and negative parts may reverse in sign under moving load: diagonals near midspan are the usual case, and they are designed for both signs or given counter-diagonals.

Derivation

  1. A stringer between panel points at x₁ and x₂ = x₁ + d carries a unit load at x as a simple beam: the panel points receive (x₂ − x)/d and (x − x₁)/d.
  2. Any truss force is a linear function of the panel-point loads, so between panel points its influence line is the straight line joining the panel-point ordinates.
  3. Chord member: cut the truss through the panel; moments about the joint where the other two cut members meet give F × h = M_beam at that joint (bottom chord, tension) or F × h = −M_beam (top chord, compression).
  4. Diagonal: vertical equilibrium of the free body gives F sin θ = ± V_panel, where V_panel is the beam shear in that panel for panel-point loading.
  5. Panel-shear line in panel j (from x_{j−1} to x_j): −x_{j−1}/L at the left panel point and 1 − x_j/L at the right panel point, joined by a straight line.
  6. Zero point of a diagonal's line inside the panel: the straight line from −x_{j−1}/L to 1 − x_j/L crosses zero at a fraction x_{j−1}/(L − d) of the panel width d from its left end.
Formulas, symbols and SI units
  • Panel-point sharing: a load at x between panel points x₁ and x₂ gives (x₂ − x)/d and (x − x₁)/d (d = panel length)
  • Chord member: F = ± M_beam(moment centre)/h (bottom chord tension +, top chord compression −) (kN)
  • Diagonal: F = ± V_panel/sin θ, with V_panel from panel-point loading (kN)
  • Panel-shear ordinates in panel j: −x_{j−1}/L and 1 − x_j/L, straight between
  • Vertical in a through Pratt truss (unloaded top joint): F = −V of the panel of the diagonal meeting it
  • Moving point load P: greatest force = P × greatest ordinate of each sign
Assumptions and limits
  • Pin-jointed truss, members carry axial force only; loads applied at panel points through stringers and cross girders.
  • Statically determinate truss with parallel chords of constant depth.
  • Linear elastic and small displacements.
  • Loads are vertical; the loaded chord (top or bottom) is identified before drawing verticals.
  • Limits: secondary bending from rigid joints, member self-weight between joints and dynamic effects are not included. Trusses with inclined chords need moment centres off the chords, and the lines are found the same way but the ordinates differ.

Codes and standards

Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.

  • Influence lines for trusses are a result of statics; no design code governs the mechanics of this lesson, and no Indian Standard clause is cited here.
  • Indian, European and American practice, side by side and not ranked, design truss bridges for their own standard railway and road loadings and set member design rules for reversal of stress and fatigue in their own steel bridge codes; those values are not reproduced here.

Worked examples

Example 1 (bottom chord and diagonal under dead and moving load)

Problem. A through Pratt truss has six panels of 4 m (span 24 m), depth 4 m and vertical end posts; in the left half each diagonal runs from a top joint down towards the centre (U0L1, U1L2, U2L3). Dead load of 20 kN acts at each interior bottom panel point L1 to L5, and a single 100 kN load can stand anywhere on the deck. Find the range of force in bottom chord L2L3 and diagonal U2L3.

  1. L2L3: cut panel 3 and take moments about U2 (above L2, x = 8 m): F = M₈/4. Peak ordinate 8 × 16/24/4 = 1.333 at L2.
  2. Dead load: R_A = 50 kN, M₈ = 50 × 8 − 20 × 4 = 320 kN m, F = 80 kN. Moving load at L2: 100 × 1.333 = 133.3 kN. Greatest tension 213.3 kN.
  3. U2L3 (θ = 45°): panel-3 shear ordinates −8/24 = −0.333 at L2 and 1 − 12/24 = +0.5 at L3; F = √2 V, so ordinates −0.471 at L2 and +0.707 at L3, with zero at 9.6 m.
  4. Dead load: panel shear 50 − 40 = 10 kN, F = 14.14 kN. Moving load at L3: +70.71 kN; at L2: −47.14 kN.
  5. Range: from 14.14 + 70.71 = 84.85 kN tension to 14.14 − 47.14 = −33.0 kN (compression), so this diagonal reverses.

Answer. L2L3: up to 213.3 kN tension; U2L3: +84.85 kN to −33.0 kN

Example 2 (top chord under a uniform lane load)

Problem. For the same truss, find the force in top chord U2U3 under a moving uniform load of 10 kN/m that covers the whole span, and under the single 100 kN load.

  1. Cut panel 3 and take moments about L3 (x = 12 m): F = −M₁₂/4. Peak ordinate −12 × 12/24/4 = −1.5 at L3; the line is a triangle from 0 at A to −1.5 at L3 to 0 at B.
  2. Uniform load over the whole span: area ½ × 24 × (−1.5) = −18 m; F = 10 × (−18) = −180 kN.
  3. Check by statics: R_A = 120 kN, M₁₂ = 120 × 12 − 10 × 12²/2 = 720 kN m, F = −720/4 = −180 kN.
  4. Single 100 kN load at L3: F = 100 × (−1.5) = −150 kN.
  5. The top chord is in compression for every load position, so it never reverses.

Answer. U2U3 = −180 kN (lane load), −150 kN (100 kN at L3)

Example 3 (vertical member of a through truss)

Problem. For the same truss, find the range of force in the vertical U2L2 under the dead load and the 100 kN moving load.

  1. Joint U2 carries no load (through truss). Its vertical equilibrium with diagonal U2L3 gives F(U2L2) = −F(U2L3) sin 45° = −V₃, minus the panel-3 shear.
  2. Ordinates: +0.333 at L2 and −0.5 at L3, straight between.
  3. Dead load: −10 kN. Moving load at L3: −50 kN; at L2: +33.3 kN.
  4. Range: from −10 − 50 = −60 kN (compression) to −10 + 33.3 = +23.3 kN (tension).
  5. In a deck truss loaded at the top chord, U2 would carry its own panel load as well, so the vertical's line would change; always check the loaded chord.

Answer. U2L2: −60 kN to +23.3 kN

Step-by-step procedure

  1. Identify the loaded chord, panel length d, depth h and the direction of every diagonal.
  2. For a chord member, find the moment centre (the joint where the other two cut members meet) and draw M_beam/h with the right sign.
  3. For a diagonal, draw the panel-shear line with the straight transition across its panel and divide by sin θ with the right sign; for a vertical, use joint equilibrium.
  4. Apply dead load as panel-point loads and moving loads at the greatest ordinates of each sign.
  5. Add dead and live effects for the greatest tension and compression, and flag members whose sign can reverse.

Site notes

  • Railway truss bridges in India and elsewhere carry the deck on stringers and cross girders, so the panel-point loading of this lesson is the real load path; stringer-to-cross-girder connections are therefore fatigue-sensitive details.
  • Diagonals near midspan that can reverse are either designed for both tension and compression or paired with counter-diagonals that act only in tension.
  • When an old truss bridge is checked for a heavier modern locomotive, the new axle train is moved across these influence lines member by member.
  • Erection of trusses by cantilevering from a pier reverses forces in some members compared with the finished bridge; the erection stages are checked separately.
Common mistakes
  • Using the beam's peaked influence line inside a panel instead of the straight line between panel points.
  • Taking moments about the wrong joint, so the other two cut members do not pass through it.
  • Getting the sign of a diagonal wrong by ignoring which way it slopes.
  • Using the through-truss result for a vertical in a deck truss.
  • Forgetting dead load when checking whether a member reverses.
Quick check

In a parallel-chord truss every chord force is a beam moment divided by the depth, and every diagonal force is a panel shear divided by the sine of its slope; the straight line across the loaded panel is the only change from beam influence lines.

Summary

  • Stringers and cross girders deliver loads at panel points, so truss influence lines are straight between panel points.
  • Chords: M_beam at the moment centre divided by h.
  • Diagonals: panel shear divided by sin θ; the line changes sign inside its panel.
  • Verticals: joint equilibrium; depends on whether the top or bottom chord is loaded.
  • Members whose line has both signs may reverse and need design for both.

Practice questions

Tap a question to see the answer.

1For the truss of Example 1, what is the ordinate of the influence line for L2L3 when the unit load stands at L3?

M₈ for a load at 12 m is a(L − x)/L = 8 × 12/24 = 4.0 m; divided by h = 4 m gives 1.0.

2For the same truss, what is the greatest compression in U2U3 caused by the 100 kN moving load alone?

100 × 1.5 = 150 kN, with the load at L3.

3Where does the influence line of diagonal U2L3 cross zero?

At 9.6 m from A: the line rises from −0.333 at 8 m to +0.5 at 12 m and crosses zero 0.4 of the panel width (1.6 m) from L2.

4Find the greatest tension and compression in diagonal U1L2 (panel 2, 4 m to 8 m) under the 100 kN moving load alone.

Panel-2 shear ordinates −4/24 = −0.167 at L1 and 1 − 8/24 = 0.667 at L2; F = √2 V. Tension 100 × 0.943 = 94.28 kN (load at L2); compression 100 × 0.236 = 23.57 kN (load at L1).

5Find the greatest force in bottom chord L1L2 under the 100 kN moving load.

Moment centre U1 (x = 4 m): peak ordinate 4 × 20/24/4 = 0.833 at L1, so 83.3 kN tension.

6Find the greatest compression in vertical U1L1 under the 100 kN moving load alone.

F(U1L1) = −V₂ (panel 2): ordinate −0.667 at L2, so 100 × 0.667 = 66.7 kN compression with the load at L2.

References

Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.

  • R. C. Hibbeler, Structural Analysis, Pearson, 10th edition, 2018.
  • C. S. Reddy, Basic Structural Analysis, Tata McGraw Hill (now McGraw Hill Education (India)), 3rd edition, 2011.
  • D. Menon, Structural Analysis, Narosa Publishing House, 2nd edition.
  • B. J. Goodno, J. M. Gere, Mechanics of Materials, Cengage Learning, 9th edition, 2018.
Suggest a correction

If something on this page is wrong, tell the editor. Your message is sent privately and is not published.

Sent privately to the Indiacon editor; not published.