6.3 Cables under point and distributed loads
After this lesson you should be able to:
- Explain why a cable carries load in pure tension and takes the funicular shape of its loading, and state the general cable theorem.
- Find the horizontal tension, the support reactions, the sag and the segment tensions of a cable under point loads, and the tension, shape and length of a cable under a uniform load per horizontal length.
- Handle supports at different levels, locate the lowest point, and choose the sag for a given allowable tension.
Theory
A cable is so flexible that it cannot resist bending or compression; it can only pull along its own length. Under any set of loads it therefore takes the one shape for which the moment is zero everywhere, the funicular shape of that loading. Hung from two points with point loads it forms a polygon of straight segments; under a load spread uniformly along the horizontal, such as a suspension bridge deck hung from the main cable, it forms a parabola; under its own weight alone, spread along its curved length, it forms a catenary. An arch is the same idea turned upside down: the cable is in tension, the arch in compression. Sign convention for this chapter: loads act downward; vertical reactions are positive upward; the horizontal thrust H of an arch is positive when the abutment pushes inward on the arch, and cable tension is positive; a bending moment that causes tension on the inner (lower) face of an arch rib is positive (sagging) and the opposite is negative (hogging); x is measured from the left support, the rise y of an arch upward from the springing line and the sag of a cable downward from the chord joining its supports.
When only vertical loads act, the horizontal component of the cable tension, H, is the same at every point, because horizontal equilibrium of any piece of cable involves only H at its two ends. The vertical component changes from point to point by the loads in between. Taking moments about any point of the cable for the part on one side gives the general cable theorem: H times the sag at that point (measured vertically from the chord joining the supports) equals the bending moment that a simple beam of the same span would have at that point under the same loads. If the sag is known at one point, H follows, and then the whole shape.
For a uniform load w per horizontal metre over a span L with sag d at midspan, the beam moment is w x(L − x)/2 and the theorem gives H = wL²/(8d) and the parabolic shape y = 4d x(L − x)/L². The tension is T = H sec θ, so it is least at the lowest point and greatest at the supports, T_max = √(H² + (wL/2)²) for level supports. Halving the sag doubles the tension, so cables are given a sag of about one ninth to one twelfth of the span in suspension bridges, balancing cable size against tower height. The cable length is about L + 8d²/(3L), which is needed to cut and set cables and to estimate the change of sag from stretch or temperature.
With supports at different levels, the theorem still works with the sag measured from the inclined chord; the lowest point moves towards the lower support and the greatest tension is at the higher support, where the slope is steepest. A cable also stretches under load by about H L/(EA) and lengthens with temperature, both of which increase the sag and slightly reduce H. Point-load cables, guy ropes and stay cables use the same statics; the difference is only in how the loads are arranged.
Derivation
- Take a cable element under a vertical load w(x) dx. Horizontal equilibrium: H at one end equals H at the other, so H is constant along the cable.
- Vertical equilibrium of the element: the change in the vertical component H dy/dx equals the load, so H d²y/dx² = w(x) with y the cable level measured upward. With z the sag below the straight chord, d²z/dx² = −d²y/dx², so H d²z/dx² = −w(x), the same equation as d²M/dx² = −w for a simple beam with M = 0 at both supports.
- Both H z and M_beam satisfy the same equation and vanish at the supports, so H z(x) = M_beam(x): the general cable theorem.
- Uniform load w per horizontal length: M_beam = w x(L − x)/2; at midspan z = d gives H = wL²/(8d) and z = 4d x(L − x)/L², a parabola.
- Tension: T = H √(1 + (dy/dx)²); for level supports the slope at a support is 4d/L, so T_max = H √(1 + 16d²/L²) = √(H² + (wL/2)²).
- Length: S = ∫₀ᴸ √(1 + (dz/dx)²) dx ≈ ∫ (1 + ½(dz/dx)²) dx = L + 8d²/(3L) for small sag ratios.
General cable theorem: H z(x) = M_beam(x), z = sag below the chord (kN, m, kN m)Uniform load per horizontal metre: H = wL²/(8d); shape z = 4d x(L − x)/L²Tension: T = H sec θ = H √(1 + (dz/dx)²); level supports: T_max = √(H² + (wL/2)²) (kN)Point load P at midspan: H = PL/(4d); segment tension T = √(H² + (P/2)²)Length (parabola, small sag): S ≈ L + 8d²/(3L) (m)Supports at different levels (chord rise c over span L): cable y = c x/L − 4d x(L − x)/L²; lowest point where dy/dx = 0
- The cable is perfectly flexible and inextensible for the shape calculation (stretch is added afterwards as a correction).
- Loads are vertical; uniform loads are per horizontal metre for the parabola (loads per unit length of cable give a catenary).
- The supports do not move; the sag at one point (or the cable length) is known.
- Self-weight of the cable is small compared with the applied load, or is included as a uniform load per horizontal metre for flat cables.
- Limits: the parabola and the length formula L + 8d²/(3L) are accurate for sag ratios up to about 1/8; deeper cables under self-weight need the catenary. Cable stretch, temperature and moving loads change the shape and are handled by deflection theory for suspension bridges.
Codes and standards
Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.
- Cable statics is a result of equilibrium; no design code governs the mechanics of this lesson, and no Indian Standard clause is cited here.
- Indian, European and American practice, side by side and not ranked, give the material grades, safety margins, fatigue rules and testing of wire ropes, strands and bridge cables in their own steel and bridge codes and product standards; those values are not reproduced here.
Worked examples
Problem. A cable spans 100 m between supports at the same level and carries 20 kN per horizontal metre with a midspan sag of 10 m. Find H, the greatest tension, its angle at the supports and the cable length.
- H = wL²/(8d) = 20 × 100²/(8 × 10) = 2 500 kN.
- Vertical reaction at each support: wL/2 = 1 000 kN.
- T_max = √(2 500² + 1 000²) = 2 692.6 kN at the supports, at tan⁻¹(4d/L) = tan⁻¹ 0.4 = 21.8° to the horizontal.
- Least tension, at midspan: T = H = 2 500 kN.
- Length: S ≈ 100 + 8 × 10²/(3 × 100) = 102.67 m (exact parabola length 102.62 m).
Answer. H = 2 500 kN; T_max = 2 692.6 kN at 21.8°; length about 102.6 m
Problem. A cable spans 30 m between level supports A and B. It carries 40 kN at 10 m from A and 60 kN at 20 m from A, and the sag under the 60 kN load is 3 m. Find H, the sag under the 40 kN load and the tension in each segment.
- Beam reactions: R_A = (40 × 20 + 60 × 10)/30 = 46.67 kN, R_B = 53.33 kN.
- Beam moment at 20 m: 53.33 × 10 = 533.3 kN m; cable theorem H = 533.3/3 = 177.8 kN.
- Beam moment at 10 m: 46.67 × 10 = 466.7 kN m; sag z = 466.7/177.8 = 2.625 m.
- Segment slopes: 2.625/10 = 0.2625, (3 − 2.625)/10 = 0.0375 and 3/10 = 0.3.
- Tensions T = H √(1 + slope²): 183.8 kN, 177.9 kN and 185.6 kN; check the vertical pull at B: 177.8 × 0.3 = 53.3 kN = R_B.
Answer. H = 177.8 kN; sag 2.625 m under the 40 kN load; segment tensions 183.8, 177.9 and 185.6 kN (greatest at B)
Problem. A service cable is carried across a valley between supports 200 m apart horizontally, the right support B being 10 m higher than A. It carries 5 kN per horizontal metre and the sag below the chord at midspan is 8 m. Find H, the position and depth of the lowest point and the tensions at both supports.
- H = wL²/(8d) = 5 × 200²/(8 × 8) = 3 125 kN (the theorem uses the sag below the inclined chord).
- Cable level above A: y = 10x/200 − 4 × 8 x(200 − x)/200² = 0.05x − 0.0008x(200 − x).
- dy/dx = 0.05 − 0.0008(200 − 2x) = 0 gives x = 68.75 m; y = 3.4375 − 7.2188 = −3.78 m, so the lowest point is 3.78 m below A.
- Slopes at the supports: −0.11 at A and +0.21 at B; T_A = 3 125 √(1 + 0.11²) = 3 143.8 kN, T_B = 3 125 √(1 + 0.21²) = 3 193.2 kN.
- Vertical reactions: 3 125 × 0.11 = 343.75 kN at A and 3 125 × 0.21 = 656.25 kN at B, adding to 5 × 200 = 1 000 kN.
Answer. H = 3 125 kN; lowest point 68.75 m from A and 3.78 m below it; T_A = 3 143.8 kN, T_B = 3 193.2 kN (greatest at the higher support)
Step-by-step procedure
- Sketch the cable, the supports, the chord between them and the loads; note the known sag (or the cable length).
- Find the simple-beam moments under the same loads.
- Use the cable theorem at the point of known sag to find H, then the sag at every other point from z = M_beam/H.
- Find the slopes of the segments (or dz/dx for a curve) and the tensions T = H √(1 + slope²); the greatest is at the steepest point.
- For supports at different levels, add the chord slope to find the actual level and the lowest point.
- Check vertical equilibrium at each support and the length or stretch if the sag must be set on site.
Site notes
- Main cables of suspension bridges, guy ropes of masts, ropeways and service cables across valleys are all designed with these equations; the sag set during erection decides the tension for the life of the structure.
- Cable length is cut and marked from the computed geometry, with allowance for elastic stretch and for the temperature at the time of setting; sag is then checked by survey at a recorded temperature.
- Anchorages and saddles must carry the full cable tension; at a saddle over a tower the horizontal components on the two sides should balance, or the tower is bent.
- Cables corrode at sockets, clamps and where water collects; inspection, dehumidification and protective wrapping are part of their maintenance.
- Wind can make light cables oscillate; dampers and cross-ties are used where vibration is seen.
- Measuring the sag from the lowest point instead of from the chord when the supports are at different levels.
- Using the parabola for a cable loaded mainly by its own weight with a large sag; that is a catenary.
- Taking the greatest tension as H; the greatest tension is at the support with the steepest slope.
- Applying the cable theorem with a moment from a beam of a different span, or forgetting loads that are not on the cable.
- Ignoring stretch and temperature when setting a sag that controls clearance.
For a uniformly loaded cable on level supports, T_max/H = √(1 + 16(d/L)²): with a sag ratio of 1/10 the greatest tension is only about 8 per cent above H, so H = wL²/(8d) gives a quick and close estimate of cable size.
Summary
- A cable carries load in pure tension and takes the funicular shape of its loading.
- With vertical loads H is constant, and H × sag below the chord = simple-beam moment (general cable theorem).
- Uniform load per horizontal length: parabola, H = wL²/(8d), T_max = √(H² + (wL/2)²) on level supports.
- Point loads give a polygon; each segment tension is H times the secant of its slope.
- For supports at different levels the sag is measured from the chord; the greatest tension is at the higher support.
Practice questions
Tap a question to see the answer.
1A cable spans 60 m with a sag of 5 m and carries 12 kN per horizontal metre. Find H and the greatest tension.
H = 12 × 60²/(8 × 5) = 1 080 kN; T_max = √(1 080² + 360²) = 1 138.4 kN.
2Find the approximate length of the cable in question 1.
S ≈ 60 + 8 × 5²/(3 × 60) = 61.11 m.
3What happens to H if the sag of a uniformly loaded cable is halved?
H = wL²/(8d) doubles, and the greatest tension rises almost as much.
4A cable of span 20 m carries a single 100 kN load at midspan with a sag of 2 m. Find H and the tension.
H = PL/(4d) = 100 × 20/8 = 250 kN; T = √(250² + 50²) = 255.0 kN in both segments.
5Why is the main cable of a suspension bridge treated as a parabola rather than a catenary?
Most of its load is the deck, spread uniformly along the horizontal, and its sag ratio is small, so the parabola fits closely.
6A cable of span 100 m carries 20 kN per horizontal metre and its tension must not exceed 3 000 kN. Find the least sag.
V = 1 000 kN, so H = √(3 000² − 1 000²) = 2 828.4 kN and d = wL²/(8H) = 200 000/22 627 = 8.84 m.
References
Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.
- R. C. Hibbeler, Structural Analysis, Pearson, 10th edition, 2018.
- C. S. Reddy, Basic Structural Analysis, Tata McGraw Hill (now McGraw Hill Education (India)), 3rd edition, 2011.
- D. Menon, Structural Analysis, Narosa Publishing House, 2nd edition.
- B. J. Goodno, J. M. Gere, Mechanics of Materials, Cengage Learning, 9th edition, 2018.