Indiacon CivilSubscribe

Textbook › Structural Analysis › Chapter 4 › Lesson 4.1

4.1 Slope-deflection method for beams

Structural Analysis Chapter 4: Displacement methods Under review — not yet three-checked Author: Indiacon

Learning objectives

After this lesson you should be able to:

  • Derive the slope-deflection equation M_AB = (2EI/L)(2θ_A + θ_B − 3ψ) + FEM_AB from the end rotations of a prismatic member.
  • Analyse continuous beams with fixed, pinned and overhanging ends by writing joint equilibrium equations in the unknown rotations.
  • Include a known support settlement through the chord rotation ψ and check every answer by statics and by an independent stiffness solution.

Theory

The force methods of Chapter 3 take redundant forces as unknowns. The displacement methods of this chapter turn the problem round: the unknowns are the rotations (and, in lesson 4.2, the sway displacements) of the joints. Once these few displacements are known, every end moment follows from one equation per member end. Sign convention for this chapter: a moment acting on the end of a member is positive when it turns clockwise, joint rotations θ are positive clockwise, and the chord rotation ψ = Δ/L is positive when the line joining the two ends of a member turns clockwise. With this rule a negative end moment at the left end of a beam span and a positive end moment at the right end both mean hogging; bending moment diagrams are still drawn with sagging positive.

Consider a straight prismatic member AB of length L and flexural rigidity EI. Its end moments depend on four things only: the rotation θ_A at A, the rotation θ_B at B, the relative sideways movement Δ of B with respect to A (expressed as the chord rotation ψ = Δ/L), and the loads applied along the span. Superposition (lesson 1.3) lets each effect be found separately on a fixed-ended beam and added. The load alone, with both ends held, gives the fixed-end moments FEM_AB and FEM_BA from lesson 3.2.

Member AB: end rotations and chord rotationABM_ABM_BAΔψ = Δ/Lθ_Aθ_BM_AB = (2EI/L)(2θ_A + θ_B − 3ψ) + FEM_ABIndiacon original, not to scale; clockwise positive
Figure 4.1: Slope-deflection: the end moments of a member come from its two end rotations, its chord rotation ψ = Δ/L and the fixed-end moments of its load. Indiacon original, not to scale.

Rotating end A by θ_A with B held needs a moment 4EIθ_A/L at A and produces 2EIθ_A/L at B: the stiffness 4EI/L and the carry-over factor ½ come straight from the moment-area or unit-load results for a beam with one end fixed. A chord rotation ψ with both ends held against rotation needs −6EIψ/L at each end (lesson 3.4). Adding the pieces gives the slope-deflection equations M_AB = (2EI/L)(2θ_A + θ_B − 3ψ) + FEM_AB and M_BA = (2EI/L)(2θ_B + θ_A − 3ψ) + FEM_BA.

For a continuous beam, the rotations at fixed supports are zero and the rotations at the other supports are unknown. At every free joint the end moments of the members meeting there must balance any applied moment: ΣM = 0 at the joint. This gives exactly as many equations as unknown rotations. If an end is pinned, either keep its rotation as an unknown with the condition M = 0, or use the reduced form M_AB = (3EI/L)(θ_A − ψ) + (FEM_AB − FEM_BA/2), which already has the pin condition built in and removes one unknown. Overhangs are statically determinate, so their moment at the support is simply entered as a known end moment.

Derivation

  1. Fix both ends of member AB and apply the span load: the end moments are the fixed-end moments FEM_AB and FEM_BA (for a uniform load w: −wL²/12 and +wL²/12; for a central point load P: −PL/8 and +PL/8, in the clockwise-positive sense).
  2. Release end A and rotate it by θ_A with B fixed. A beam propped at A and fixed at B, loaded by an end moment M at A, rotates by θ_A = ML/(4EI), and the moment at B is M/2. So M_AB = 4EIθ_A/L and M_BA = 2EIθ_A/L.
  3. In the same way θ_B alone gives M_BA = 4EIθ_B/L and M_AB = 2EIθ_B/L.
  4. Move B sideways by Δ relative to A with both end rotations held at zero. The member takes the S shape of lesson 3.4 and both end moments equal −6EIΔ/L² = −6EIψ/L (anticlockwise when the chord turns clockwise).
  5. Add the four parts: M_AB = (2EI/L)(2θ_A + θ_B − 3ψ) + FEM_AB and M_BA = (2EI/L)(2θ_B + θ_A − 3ψ) + FEM_BA.
  6. If B is a pin with M_BA = 0, eliminate θ_B from the second equation: θ_B = −θ_A/2 + 3ψ/2 − FEM_BA L/(4EI). Substituting gives the reduced form M_AB = (3EI/L)(θ_A − ψ) + FEM_AB − FEM_BA/2.
Formulas, symbols and SI units
  • M_AB = (2EI/L)(2θ_A + θ_B − 3ψ) + FEM_AB; M_BA = (2EI/L)(2θ_B + θ_A − 3ψ) + FEM_BA (kN m, with EI in kN m², L in m, θ and ψ in radians)
  • Far end pinned: M_AB = (3EI/L)(θ_A − ψ) + FEM_AB − FEM_BA/2
  • Chord rotation ψ = Δ/L, positive clockwise; a support B settling by Δ below A gives ψ_AB = +Δ/L
  • Fixed-end moments (clockwise positive): uniform load w: ∓wL²/12; central point load P: ∓PL/8; point load at a from A: −Pab²/L² and +Pa²b/L²
  • Joint equilibrium: Σ (end moments at the joint) = applied clockwise joint moment (zero if none)
  • Propped cantilever check: fixed-end moment −wL²/8, rotation at the prop wL³/(48EI)
Assumptions and limits
  • Linear elastic material, small rotations and small deflections, so superposition holds.
  • Prismatic members (constant EI along each member); members with haunches or steps need their own stiffness and carry-over factors.
  • Bending deformation only: axial and shear deformations are ignored, so a beam's length does not change.
  • Joints are rigid: all member ends meeting at a joint rotate by the same angle.
  • Limits: the hand method is practical for up to about three or four unknown displacements; beyond that the same equations are assembled in matrix form (the stiffness method). Results depend on relative EI, so cracked concrete needs realistic stiffness values.

Codes and standards

Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.

  • The slope-deflection method is a result of mechanics; no design code governs the mechanics of this lesson, and no Indian Standard clause is cited here.
  • Indian, European and American practice, side by side and not ranked, use elastic analysis of this kind for continuous beams, by hand or by computer; load values, load combinations, stiffness assumptions for cracked members and any permitted redistribution of moments are set in each practice's own codes and are not reproduced here.

Worked examples

Example 1 (two-span floor beam, fixed at one end)

Problem. A floor beam ABC is fixed at A, supported on a roller at B and pinned at C. Span AB = 6 m carries 20 kN/m; span BC = 4 m carries a central point load of 40 kN. EI is constant. Find the support moments and the reactions.

  1. Unknown: θ_B only (A is fixed; use the reduced form for BC because C is a pin). Fixed-end moments: FEM_AB = −20 × 36/12 = −60 kN m, FEM_BA = +60 kN m; FEM_BC = −40 × 4/8 = −20 kN m, FEM_CB = +20 kN m.
  2. Slope-deflection: M_AB = (2EI/6)(θ_B) − 60 = (EI/3)θ_B − 60; M_BA = (2EI/6)(2θ_B) + 60 = (2EI/3)θ_B + 60; M_BC = (3EI/4)θ_B + (−20 − 20/2) = 0.75EIθ_B − 30.
  3. Joint B: M_BA + M_BC = 0 gives (0.6667 + 0.75)EIθ_B = −30, so EIθ_B = −21.18 kN m² (anticlockwise).
  4. End moments: M_AB = −7.06 − 60 = −67.06 kN m; M_BA = −14.12 + 60 = +45.88 kN m; M_BC = −45.88 kN m. Both support moments are hogging: 67.06 kN m at A and 45.88 kN m at B.
  5. Reactions by statics: span AB, R_A = 60 + (67.06 − 45.88)/6 = 63.53 kN; span BC, R_C = 20 − 45.88/4 = 8.53 kN; R_B = 160 − 63.53 − 8.53 = 87.94 kN. Check: the sum is 160 kN, the total load.

Answer. M_A = −67.06 kN m, M_B = −45.88 kN m (hogging); R_A = 63.53 kN, R_B = 87.94 kN, R_C = 8.53 kN

Example 2 (continuous beam with a settling support)

Problem. A beam ABC is fixed at A and on rollers at B and C, with two spans of 5 m each carrying 24 kN/m. EI = 4 × 10⁴ kN m². Support B settles 10 mm. Find the moments and reactions, and compare with the case without settlement.

  1. Chord rotations: ψ_AB = +0.010/5 = +0.002 rad (B below A, chord turns clockwise); ψ_BC = −0.002 rad. FEM = ±24 × 25/12 = ±50 kN m. 2EI/L = 16 000 kN m and 3EI/L = 24 000 kN m.
  2. M_BA = 16 000(2θ_B − 0.006) + 50 = 32 000θ_B − 46; M_BC (C pinned) = 24 000(θ_B + 0.002) + (−50 − 25) = 24 000θ_B − 27.
  3. Joint B: 56 000θ_B − 73 = 0, so θ_B = 0.001304 rad (clockwise).
  4. M_AB = 16 000(0.001304 − 0.006) − 50 = −125.14 kN m; M_BA = 41.71 − 46 = −4.29 kN m, so the moment over B is +4.29 kN m (slightly sagging).
  5. Reactions by moments about B for each span, with the end moments as applied couples: 5R_A = 300 + 125.14 + 4.29, so R_A = 85.89 kN; 5R_C = 300 + 4.29, so R_C = 60.86 kN; R_B = 240 − 85.89 − 60.86 = 93.26 kN. Without settlement the same steps give M_A = −42.86 kN m and M_B = −64.29 kN m: the 10 mm settlement nearly triples the hogging at the fixed end and removes the hogging over B.

Answer. M_A = −125.14 kN m, M_B = +4.29 kN m; R_A = 85.89 kN, R_B = 93.26 kN, R_C = 60.86 kN

Example 3 (beam with an overhang)

Problem. A beam AB is fixed at A and supported on a roller at B; span AB = 6 m carries 15 kN/m. An overhang BC of 2 m carries a point load of 30 kN at C. EI is constant. Find the moments at A and B.

  1. The overhang is determinate. Moments on the free body BC about B: the load turns BC clockwise by 30 × 2 = 60 kN m, so the end moment on BC at B is M_BC = −60 kN m.
  2. Unknown θ_B. FEM_AB = −15 × 36/12 = −45 kN m, FEM_BA = +45 kN m.
  3. M_BA = (2EI/6)(2θ_B) + 45 = (2EI/3)θ_B + 45. Joint B: M_BA + M_BC = 0 gives M_BA = +60, so EIθ_B = 22.5 kN m² (clockwise).
  4. M_AB = (2EI/6)θ_B − 45 = 7.5 − 45 = −37.5 kN m.
  5. Bending moments: −37.5 kN m (hogging) at A, −60 kN m (hogging) at B. Reactions: R_A = 45 + (37.5 − 60)/6 = 41.25 kN, R_B = 90 + 30 − 41.25 = 78.75 kN.

Answer. M_A = −37.5 kN m, M_B = −60 kN m; R_A = 41.25 kN, R_B = 78.75 kN

Step-by-step procedure

  1. Fix the sign convention (clockwise positive end moments, rotations and chord rotations) and number the unknown joint rotations; fixed ends have θ = 0.
  2. Work out the fixed-end moments of every loaded span and the chord rotation ψ = Δ/L of any span with a known settlement.
  3. Write the slope-deflection equation for each member end, using the reduced form where the far end is a pin.
  4. Write one joint equilibrium equation per unknown rotation and solve.
  5. Back-substitute for the end moments, convert to sagging-positive bending moments, then find reactions and span moments by statics and check that the reactions add up to the total load.

Site notes

  • Continuous beams in buildings and bridges are analysed today by stiffness programs that use exactly these member equations; a quick slope-deflection hand check on one bay catches input errors such as a wrong support condition.
  • A support that settles sheds load to its neighbours and can even reverse the moment over it, as Example 2 shows; foundation movement estimates belong in the analysis of continuous members.
  • Overhangs relieve the hogging moment at the fixed end and increase it at the first support; balcony and canopy beams are typical cases.
  • Where the real end connection is partly fixed, analyse both the fixed and pinned cases to bracket the moments rather than trusting one idealisation.
Common mistakes
  • Mixing sign conventions: using sagging-positive moments inside the slope-deflection equation instead of clockwise-positive end moments.
  • Taking the wrong sign of ψ for a settling support (B lower than A makes ψ_AB positive and ψ_BC negative).
  • Using 4EI/L for a member whose far end is a pin and also adding the pin condition, or using the reduced form without the FEM correction −FEM_BA/2.
  • Forgetting that the overhang moment is known and enters the joint equation directly.
  • Stopping at end moments without checking the reactions against the total load.
Quick check

For a prismatic member the stiffness against end rotation is 4EI/L with the far end fixed and 3EI/L with the far end pinned, and the carry-over to a fixed far end is one half. These three numbers, together with the fixed-end moments, are all the slope-deflection method needs for beams without sway.

Summary

  • Unknowns are joint rotations; end moments follow from M_AB = (2EI/L)(2θ_A + θ_B − 3ψ) + FEM_AB.
  • A pinned far end gives the reduced form (3EI/L)(θ_A − ψ) + FEM_AB − FEM_BA/2.
  • One joint equilibrium equation per unknown rotation.
  • Settlement enters through ψ = Δ/L; overhang moments enter as known end moments.
  • Always convert to sagging-positive bending moments and check reactions by statics.

Practice questions

Tap a question to see the answer.

1A propped cantilever AB, fixed at A and pinned at B, has span 6 m and carries 10 kN/m. Find θ_B and M_AB by slope-deflection.

M_BA = (2EI/6)(2θ_B) + 30 = 0 gives EIθ_B = −45 kN m² (anticlockwise); M_AB = (2EI/6)θ_B − 30 = −15 − 30 = −45 kN m = −wL²/8.

2A fixed-ended beam of span 5 m (EI = 2 × 10⁴ kN m²) has its end A turned 0.001 rad clockwise by a connected member, with no load and B held. Find M_AB and M_BA.

M_AB = (2EI/L)(2θ_A) = 8000 × 0.002 = 16 kN m; M_BA = 8000 × 0.001 = 8 kN m (carry-over one half).

3A beam has two equal spans of 4 m on simple supports and carries 30 kN/m throughout. Use symmetry and slope-deflection to find the moment over the middle support.

By symmetry θ_B = 0; reduced form for each span: M_BA = 0 + (30 × 16/12) + (30 × 16/12)/2 = 60 kN m, so the moment over B is −60 kN m (hogging) = −wL²/8.

4In Example 1, remove the 40 kN load from span BC. Find the moments at A and B and the reaction at C.

EIθ_B = −60/1.4167 = −42.35 kN m²; M_AB = −14.12 − 60 = −74.12 kN m; M_B = −31.76 kN m (hogging); R_C = −31.76/4 = −7.94 kN, a downward (hold-down) reaction.

5A fixed-ended beam of span 6 m (EI = 3 × 10⁴ kN m²) carries no load and support B settles 6 mm. Find the end moments.

ψ = 0.001 rad; M_AB = M_BA = (2EI/L)(−3ψ) = 10 000 × (−0.003) = −30 kN m each (−6EIΔ/L²): hogging 30 kN m at A and sagging 30 kN m at B.

6In Example 3, the overhang load is increased to 45 kN. Find θ_B and the moment at A.

M_BC = −90 kN m, so M_BA = +90 = (2EI/3)θ_B + 45, EIθ_B = 67.5 kN m²; M_AB = 22.5 − 45 = −22.5 kN m (hogging).

References

Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.

  • R. C. Hibbeler, Structural Analysis, Pearson, 10th edition, 2018.
  • C. S. Reddy, Basic Structural Analysis, Tata McGraw Hill (now McGraw Hill Education (India)), 3rd edition, 2011.
  • D. Menon, Structural Analysis, Narosa Publishing House, 2nd edition.
  • B. J. Goodno, J. M. Gere, Mechanics of Materials, Cengage Learning, 9th edition, 2018.
Suggest a correction

If something on this page is wrong, tell the editor. Your message is sent privately and is not published.

Sent privately to the Indiacon editor; not published.