Indiacon CivilSubscribe

Textbook › Structural Analysis › Chapter 3 › Lesson 3.2

3.2 Propped cantilevers and fixed beams

Structural Analysis Chapter 3: Force method Under review — not yet three-checked Author: Indiacon

Learning objectives

After this lesson you should be able to:

  • Analyse propped cantilevers and fixed (encastré) beams by the force method, using the prop reaction or the end moments as redundants.
  • Derive and use the standard results: 3wL/8 and −wL²/8 for a propped cantilever, fixed-end moments wL²/12, PL/8 and Pab²/L², Pa²b/L².
  • Locate the maximum sagging moment and the points of contraflexure, and compare deflections with the simply supported case.

Theory

A propped cantilever is fixed at one end and simply supported at the other: four reactions (three at the fixed end, one at the prop) against three equations, so it is indeterminate to the first degree for general loading, and under vertical loads only the vertical reaction and moment matter. A fixed beam is built in at both ends; under vertical loads the two end moments are the redundants. Sign convention as in this chapter: sagging moment positive, so fixed-end moments are negative (hogging); reactions positive upward; deflection positive downward when quoted as a sag.

For the propped cantilever, release the prop. The primary structure is a cantilever, whose tip deflects under the load; the prop reaction R must push the tip back to zero. For a uniform load w over span L, the tip deflection is wL⁴/(8EI) and a unit upward tip load lifts it L³/(3EI), so R = 3wL/8. The wall moment is then M_A = (3wL/8)L − wL²/2 = −wL²/8, the same size as the simple-span midspan moment, and the largest sagging moment, 9wL²/128, occurs 3L/8 from the prop where the shear is zero.

w−wL²/12−wL²/12+wL²/240.211Ldashed: free diagram wL²/8Indiacon original
Figure 3.2: Fixed beam under a uniform load: the free moment parabola (span wL²/8) is closed by a straight line at the fixed-end moments −wL²/12, leaving +wL²/24 at midspan and contraflexure at 0.211L from each end. Indiacon original, not to scale.

For the fixed beam, release the rotations at both ends. The primary structure is a simple span, whose end slopes under load are θ_A0 and θ_B0; equal end moments M applied to a simple span rotate each end by ML/(2EI) (ML/(3EI) at the near end plus ML/(6EI) from the far end). Compatibility, zero slope at both ends, gives the fixed-end moments. Under a full uniform load the end slopes are wL³/(24EI), so M = wL²/12; under a central point load they are PL²/(16EI), so M = PL/8; for a point load at distances a and b from the ends, M_A = Pab²/L² and M_B = Pa²b/L². These fixed-end moments are the starting values of slope-deflection and moment distribution (Chapter 4).

Fixity reduces both moment and deflection. A fixed beam under uniform load has end moments wL²/12 and midspan moment wL²/24, a range of wL²/8 shared between hogging and sagging, and a midspan deflection wL⁴/(384EI), one fifth of the simple-span value. The free moment diagram (the simple-span diagram) is the same in every case; fixing the ends only shifts the closing line. Real ends are seldom fully fixed: a beam framing into a flexible column or wall rotates a little, the end moments fall and the span moment rises, so designers often check both the fixed and the pinned extremes.

Derivation

  1. Propped cantilever, uniform load: release the prop at B; the cantilever tip deflects Δ_B0 = wL⁴/(8EI) downward.
  2. A unit upward load at B lifts it f = L³/(3EI). Compatibility: R L³/(3EI) = wL⁴/(8EI), so R_B = 3wL/8 and R_A = 5wL/8.
  3. Moments: M(x) = R_B x − w x²/2 from the prop; M_A = −wL²/8; shear zero at x = 3L/8, where M = 9wL²/128; M = 0 again at x = 3L/4.
  4. Fixed beam: release both end rotations; the simple span under the load has end slopes θ_A0, θ_B0. End moments M_A, M_B (hogging) rotate the ends by (M_A L/3 + M_B L/6)/EI and (M_A L/6 + M_B L/3)/EI.
  5. Compatibility (zero end slopes) for a uniform load: θ_0 = wL³/(24EI) = M L/(2EI), so M_A = M_B = wL²/12; for a central load θ_0 = PL²/(16EI) gives PL/8.
  6. Point load P at a from A (b = L − a): solving the two compatibility equations gives M_A = Pab²/L², M_B = Pa²b/L², reactions R_A = Pb²(3a + b)/L³, R_B = Pa²(a + 3b)/L³, and moment under the load 2Pa²b²/L³.
Formulas, symbols and SI units
  • Propped cantilever, uniform load w (kN/m), span L (m): R_prop = 3wL/8, R_fixed = 5wL/8, M_fixed = −wL²/8, M_max = +9wL²/128 at 3L/8 from the prop
  • Propped cantilever, central point load P (kN): R_prop = 5P/16, M_fixed = −3PL/16, M under load = +5PL/32
  • Fixed beam, uniform load: M_ends = −wL²/12, M_mid = +wL²/24, δ_mid = wL⁴/(384EI) (EI in kN m², δ in m)
  • Fixed beam, central point load: M_ends = −PL/8, M_mid = +PL/8, δ_mid = PL³/(192EI)
  • Fixed beam, point load at a from A (b = L − a): M_A = −Pab²/L², M_B = −Pa²b/L², R_A = Pb²(3a + b)/L³
  • Points of contraflexure, fixed beam with uniform load: x = 0.211L from each end
Assumptions and limits
  • Linear elastic, prismatic members (constant EI) with small deflections; bending deformation only.
  • Fixed ends allow no rotation and no vertical movement; the prop is unyielding (settlement is treated in lesson 3.4).
  • Loads act vertically; axial restraint effects (arching or catenary action) are ignored.
  • The free moment diagram of the simple span is known for the given loading.
  • Limits: real supports give partial fixity, so end moments lie between zero and the fixed-end values; cracking of concrete near supports reduces end stiffness and shifts moment towards midspan.

Codes and standards

Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.

  • Propped cantilever and fixed-beam results are results of mechanics; no design code governs the mechanics of this lesson, and no Indian Standard clause is cited here.
  • Indian, European and American practice, side by side and not ranked, use these elastic moments as the starting point of analysis; moment coefficients for design, partial-fixity allowances and redistribution limits are set in each practice's own codes and are not reproduced here.

Worked examples

Example 1 (propped cantilever lintel beam)

Problem. A beam over a store-room opening is built into a stiff wall at A and rests on a column at B; span 6 m, uniform load 25 kN/m. Treat A as fixed and B as a simple support. Find the reactions, the wall moment, the largest sagging moment and the point of zero moment.

  1. Release the prop: R_B = 3wL/8 = 3 × 25 × 6/8 = 56.25 kN; R_A = 150 − 56.25 = 93.75 kN.
  2. Wall moment: M_A = 56.25 × 6 − 25 × 6²/2 = 337.5 − 450 = −112.5 kN m (= −wL²/8).
  3. Shear is zero at x = R_B/w = 56.25/25 = 2.25 m from B (= 3L/8).
  4. Largest sagging moment: 56.25 × 2.25 − 25 × 2.25²/2 = 126.56 − 63.28 = +63.28 kN m (= 9wL²/128).
  5. Zero moment where 56.25x = 12.5x², x = 4.5 m from B, that is 1.5 m from the wall: top bars at the wall must run past this point.

Answer. R_B = 56.25 kN, R_A = 93.75 kN, M_A = −112.5 kN m, M_max = +63.28 kN m at 2.25 m from B, zero moment 1.5 m from the wall

Example 2 (fixed beam under a uniform load, moments and deflection)

Problem. A beam of span 8 m is cast monolithically between two very stiff walls and carries 30 kN/m. EI = 1.5 × 10⁵ kN m². Find the end and midspan moments and the midspan deflection, and compare with a simple span.

  1. End moments: M_A = M_B = −wL²/12 = −30 × 64/12 = −160 kN m.
  2. Free (simple-span) moment wL²/8 = 240 kN m; midspan moment = 240 − 160 = +80 kN m (= wL²/24).
  3. Midspan deflection: wL⁴/(384EI) = 30 × 4096/(384 × 1.5 × 10⁵) = 2.13 mm.
  4. Simple span for comparison: 5wL⁴/(384EI) = 10.67 mm and midspan moment 240 kN m.
  5. Fixity cuts the deflection to one fifth and the largest moment to 2/3 of the simple-span value (160 against 240 kN m), but only if the walls really prevent rotation.

Answer. M_ends = −160 kN m, M_mid = +80 kN m, δ = 2.13 mm (10.67 mm if simply supported)

Example 3 (fixed beam with an off-centre point load from a machine)

Problem. A fixed beam of span 6 m carries a machine load of 90 kN at 2 m from end A. Find the fixed-end moments, the reactions and the moment under the load.

  1. a = 2 m, b = 4 m. M_A = −Pab²/L² = −90 × 2 × 16/36 = −80 kN m; M_B = −Pa²b/L² = −90 × 4 × 4/36 = −40 kN m.
  2. Reactions: R_A = Pb/L + (|M_A| − |M_B|)/L = 60 + 40/6 = 66.67 kN; R_B = 90 − 66.67 = 23.33 kN. Check: Pb²(3a + b)/L³ = 90 × 16 × 10/216 = 66.67 kN.
  3. Moment under the load: R_A × 2 − 80 = 133.33 − 80 = +53.33 kN m (= 2Pa²b²/L³).
  4. The nearer end attracts the larger moment and the larger reaction.
  5. Simple-span moment under the load would be Pab/L = 120 kN m; the closing line from −80 to −40 reduces it to 53.33 kN m.

Answer. M_A = −80 kN m, M_B = −40 kN m, R_A = 66.67 kN, R_B = 23.33 kN, +53.33 kN m under the load

Step-by-step procedure

  1. Identify the redundants: the prop reaction for a propped cantilever, the two end moments for a fixed beam under vertical load.
  2. Find the primary deflection or end slopes under the load (standard results or the unit load method).
  3. Write compatibility (zero deflection at the prop, zero slope at fixed ends) and solve for the redundants.
  4. Draw the free moment diagram and the closing line through the end moments; the final diagram is their sum.
  5. Find maximum sagging at zero shear, points of contraflexure where M = 0, and check reactions by equilibrium.

Site notes

  • Top reinforcement over a fixed or built-in end must extend beyond the point of contraflexure (0.211L for a fixed beam, L/4 for a propped cantilever under uniform load) with enough anchorage.
  • A beam assumed fixed but sitting on a thin wall behaves closer to simply supported: expect cracks at midspan if only end steel was provided and fixity was lost.
  • Cantilever balconies propped later by a column turn into propped cantilevers: the root moment drops, but the new prop must be founded so that it does not settle (lesson 3.4).
  • Heavy point loads such as machines or tanks should be placed near supports where possible: the nearer end takes most of the load and the span moment falls.
Common mistakes
  • Taking the fixed-end moment as wL²/8 (that is the propped-cantilever wall moment and the simple-span midspan value).
  • Swapping a and b in Pab²/L²: the end nearer the load gets the larger moment.
  • Forgetting the sign convention: fixed-end moments are hogging (negative) under downward load.
  • Placing the maximum sagging moment of a propped cantilever at midspan instead of 3L/8 from the prop.
  • Assuming full fixity where the support can rotate.
Quick check

Under a uniform load the midspan moment always equals the free value wL²/8 minus the average of the two end hogging moments: simple span +wL²/8; propped cantilever wL²/8 − wL²/16 = +wL²/16 at midspan (the maximum, 9wL²/128, lies 3L/8 from the prop); fixed beam wL²/8 − wL²/12 = +wL²/24. If your end and midspan values do not fit this, recheck. Valid for prismatic beams in the elastic range.

Summary

  • Propped cantilever: R_prop = 3wL/8, M_fixed = −wL²/8, M_max = 9wL²/128 at 3L/8 from the prop.
  • Fixed beam: −wL²/12 at the ends, +wL²/24 at midspan, deflection one fifth of the simple span.
  • Off-centre point load: M_A = Pab²/L², M_B = Pa²b/L²; the nearer end takes more.
  • Final diagram = free moment diagram + closing line through the end moments.
  • Real ends are partly fixed; check both extremes where it matters.

Practice questions

Tap a question to see the answer.

1A propped cantilever of span 5 m carries a central point load of 40 kN. Find the prop reaction, the fixed-end moment and the moment under the load.

R_prop = 5P/16 = 12.5 kN; M_fixed = −3PL/16 = −37.5 kN m; M under load = 12.5 × 2.5 = +31.25 kN m (= 5PL/32).

2A fixed beam of span 4 m carries a central load of 60 kN; EI = 2 × 10⁴ kN m². Find the end and midspan moments and the midspan deflection.

M_ends = −PL/8 = −30 kN m; M_mid = +30 kN m; δ = PL³/(192EI) = 60 × 64/(192 × 2 × 10⁴) = 1.0 mm.

3A fixed beam of span 7.5 m carries 20 kN/m. Find the end and midspan moments and the points of contraflexure.

M_ends = −20 × 56.25/12 = −93.75 kN m; M_mid = +46.875 kN m; contraflexure at 0.211 × 7.5 = 1.585 m from each end.

4A propped cantilever of span 8 m carries 10 kN/m. Where is the largest sagging moment and how large is it?

R_prop = 3 × 10 × 8/8 = 30 kN; zero shear at 30/10 = 3 m from the prop (3L/8); M = 30 × 3 − 10 × 9/2 = +45 kN m (= 9wL²/128).

5A fixed beam of span 9 m carries 27 kN at L/3 from end A. Find both fixed-end moments.

a = 3 m, b = 6 m: M_A = −27 × 3 × 36/81 = −36 kN m; M_B = −27 × 9 × 6/81 = −18 kN m.

6A beam designed as fixed at both ends under a uniform load is found to have ends that can rotate freely. What happens to the midspan moment?

It rises from wL²/24 to wL²/8, three times larger, and the deflection rises fivefold; midspan reinforcement designed for the fixed case would be inadequate.

References

Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.

  • R. C. Hibbeler, Structural Analysis, Pearson, 10th edition, 2018.
  • C. S. Reddy, Basic Structural Analysis, Tata McGraw Hill (now McGraw Hill Education (India)), 3rd edition, 2011.
  • D. Menon, Structural Analysis, Narosa Publishing House, 2nd edition.
  • B. J. Goodno, J. M. Gere, Mechanics of Materials, Cengage Learning, 9th edition, 2018.
Suggest a correction

If something on this page is wrong, tell the editor. Your message is sent privately and is not published.

Sent privately to the Indiacon editor; not published.