Indiacon CivilSubscribe

Textbook › Structural Analysis › Chapter 3 › Lesson 3.3

3.3 Three-moment equation for continuous beams

Structural Analysis Chapter 3: Force method Under review — not yet three-checked Author: Indiacon

Learning objectives

After this lesson you should be able to:

  • Derive Clapeyron's three-moment equation for two adjacent spans of a continuous beam from slope continuity at the common support.
  • Use the load terms 6Ax̄/L for uniform, central and off-centre point loads, and handle fixed ends, overhangs and spans of different stiffness.
  • Find support moments, reactions and span moments of continuous beams, and check them against the force-method results of lesson 3.1.

Theory

A continuous beam runs over several supports. If the moments over the supports are taken as the redundants, each span becomes a simple span loaded by its own loads plus the two end moments, and its behaviour is easy to describe. The only compatibility condition left is that the beam does not kink over an interior support: the slope at the end of one span must equal the slope at the start of the next. Writing this condition for every interior support gives one equation linking three consecutive support moments, Clapeyron's three-moment equation. Sign convention for this lesson: support moments positive when sagging, so they usually come out negative (hogging); x̄ for each span is measured from its far (outer) support; reactions positive upward.

For supports A, B and C with span L₁ (A to B, second moment of area I₁) and span L₂ (B to C, I₂), and constant E, the equation is M_A L₁/I₁ + 2M_B (L₁/I₁ + L₂/I₂) + M_C L₂/I₂ = −6A₁x̄₁/(I₁L₁) − 6A₂x̄₂/(I₂L₂). Here A₁ and A₂ are the areas of the free (simple-span) bending moment diagrams of the two spans, x̄₁ is the distance of the centroid of A₁ from A, and x̄₂ the distance of the centroid of A₂ from C. The left side depends only on the geometry; the right side holds the loads through the load terms 6Ax̄/L, which are standard: wL³/4 for a full uniform load, 3PL²/8 for a central point load and Pab(L + a)/L for a point load at distance a from the far support (b = L − a).

wPM_AM_BM_CL₁, I₁L₂, I₂A₁A₂x̄₁x̄₂Indiacon original
Figure 3.3: Three-moment equation: each span is a simple span with its free moment diagram (area A, centroid x̄ from the outer support) plus the support moments M_A, M_B, M_C. Indiacon original, not to scale.

End conditions are handled simply. At a simple end support the moment is zero. At an end with an overhang the support moment is known from statics (the cantilever moment of the overhang loads). At a fixed end the slope is zero; this is modelled by adding an imaginary span of zero length beyond the fixed end, which gives an extra equation 2M_A L₁ + M_B L₁ = −6A₁x̄₁'/L₁ with x̄₁' measured from B. With n unknown support moments there are n equations; for a beam with equal spans the equations are short and usually symmetric.

Once the support moments are known, each span is a simple span with end moments. The reactions follow from span equilibrium, R_left = (simple-span reaction) + (M_right − M_left)/L for sagging-positive moments, and the span moment diagram is the free diagram plus the straight closing line between the support moments. The equation also shows why stiffness matters: a span with larger I has smaller L/I and attracts more moment to its supports. Settlement of supports adds a term on the right-hand side, treated in lesson 3.4.

Derivation

  1. Cut the beam over the supports so that each span is a simple span carrying its loads plus end moments M_A, M_B (span 1) and M_B, M_C (span 2), all sagging positive.
  2. Span 1, slope at B by the area-moment method: the free moment diagram rotates end B by A₁x̄₁/(EI₁L₁) (clockwise for downward load), and the end moments rotate it by −(M_A L₁/6 + M_B L₁/3)/(EI₁).
  3. Span 2, slope at B: the free diagram rotates end B by A₂x̄₂/(EI₂L₂) in the opposite sense, and the end moments by −(M_C L₂/6 + M_B L₂/3)/(EI₂).
  4. Continuity: the beam is continuous over B, so the two end rotations at B are equal and opposite in this measure (no kink). Adding them and multiplying by 6E gives M_A L₁/I₁ + 2M_B(L₁/I₁ + L₂/I₂) + M_C L₂/I₂ = −6A₁x̄₁/(I₁L₁) − 6A₂x̄₂/(I₂L₂).
  5. Load terms: full uniform load, A = wL³/12 and x̄ = L/2, so 6Ax̄/L = wL³/4; central point load, A = PL²/8, x̄ = L/2, so 3PL²/8; point load at a from the far end, A = Pab/2, x̄ = (L + a)/3, so Pab(L + a)/L.
  6. Check for two equal spans L under w with simple ends: 2M_B(2L) = −2wL³/4, so M_B = −wL²/8, the same as the force-method result of lesson 3.1.
Formulas, symbols and SI units
  • Three-moment equation: M_A L₁/I₁ + 2M_B(L₁/I₁ + L₂/I₂) + M_C L₂/I₂ = −6A₁x̄₁/(I₁L₁) − 6A₂x̄₂/(I₂L₂) (moments in kN m, L in m)
  • Constant I: M_A L₁ + 2M_B(L₁ + L₂) + M_C L₂ = −6A₁x̄₁/L₁ − 6A₂x̄₂/L₂
  • Load terms 6Ax̄/L: uniform load wL³/4; central point load 3PL²/8; point load at a from the far support Pab(L + a)/L (kN m², with w in kN/m, P in kN)
  • Fixed end: add a zero-length span beyond it, giving 2M_A L₁ + M_B L₁ = −6A₁x̄₁'/L₁ (x̄₁' from the inner support)
  • Span reactions: R_left = R_left,0 + (M_right − M_left)/L; R_right = R_right,0 + (M_left − M_right)/L
  • Equal spans l under w: two spans M_B = −wl²/8; three spans M_B = M_C = −wl²/10
Assumptions and limits
  • Linear elastic beam, small deflections, bending deformation only; E constant along the beam, I constant within each span.
  • Supports at the same level and unyielding (settlement is added in lesson 3.4).
  • Loads vertical; x̄ measured from the outer support of each span.
  • Fixed ends modelled by an imaginary zero-length span; overhang moments found from statics.
  • Limits: spans with varying I within the span need the M/EI diagram integrated directly; for many spans or frames with sway, moment distribution or matrix methods (Chapter 4 onwards) are more convenient.

Codes and standards

Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.

  • The three-moment equation is a result of mechanics; no design code governs the mechanics of this lesson, and no Indian Standard clause is cited here.
  • Indian, European and American practice, side by side and not ranked, analyse continuous beams elastically by this or equivalent methods; tabulated moment coefficients for design, pattern-loading rules and redistribution limits are set in each practice's own codes and are not reproduced here.

Worked examples

Example 1 (two unequal spans with mixed loads)

Problem. A continuous beam ABC is simply supported at A, B and C, with span AB = 6 m carrying 20 kN/m and span BC = 4 m carrying a central point load of 60 kN; EI constant. Find M_B, the reactions and the largest span moments.

  1. Load terms: span AB, wL³/4 = 20 × 216/4 = 1080; span BC, 3PL²/8 = 3 × 60 × 16/8 = 360.
  2. Three-moment equation with M_A = M_C = 0: 2M_B(6 + 4) = −1080 − 360, so M_B = −1440/20 = −72 kN m.
  3. Span AB: R_A = 60 + (−72 − 0)/6 = 48 kN, R_B,left = 60 + 12 = 72 kN. Span BC: R_C = 30 − 72/4 = 12 kN, R_B,right = 30 + 18 = 48 kN; R_B = 120 kN. Check: 48 + 120 + 12 = 180 kN = 120 + 60.
  4. Span AB: zero shear at 48/20 = 2.4 m from A, M = 48 × 2.4 − 20 × 2.4²/2 = +57.6 kN m.
  5. Span BC: under the load, M = 12 × 2 = +24 kN m. The hogging moment of 72 kN m over B governs.

Answer. M_B = −72 kN m; R_A = 48, R_B = 120, R_C = 12 kN; +57.6 kN m in AB, +24 kN m in BC

Example 2 (fixed end at a wall, imaginary span)

Problem. A beam ABC is fixed into a wall at A and simply supported at B and C; AB = BC = 5 m, EI constant, uniform load 18 kN/m on both spans. Find M_A and M_B and the reactions.

  1. Load term for each span: wL³/4 = 18 × 125/4 = 562.5.
  2. Imaginary zero-length span A₀A at the fixed end: 2M_A(0 + 5) + M_B × 5 = −562.5, that is 10M_A + 5M_B = −562.5.
  3. Supports A, B, C (M_C = 0): 5M_A + 2M_B(10) = −562.5 − 562.5, that is 5M_A + 20M_B = −1125.
  4. Solving: M_B = −843.75/17.5 = −48.21 kN m and M_A = −32.14 kN m.
  5. Reactions: R_A = 45 + (M_B − M_A)/5 = 45 − 3.21 = 41.79 kN; R_C = 45 + (M_B − 0)/5 = 35.36 kN; R_B = 180 − 41.79 − 35.36 = 102.86 kN.

Answer. M_A = −32.14 kN m, M_B = −48.21 kN m; R_A = 41.79, R_B = 102.86, R_C = 35.36 kN

Example 3 (spans of different stiffness, end uplift)

Problem. A beam ABC has two 6 m spans on simple supports. Span AB has second moment of area I and carries 15 kN/m; span BC is unloaded and has 2I. Find M_B and the reactions, and compare with equal I in both spans.

  1. Load term for AB: wL³/4 = 15 × 216/4 = 810; divided by I₁ = I. Span BC has no load term.
  2. Equation: 2M_B(6/I + 6/(2I)) = −810/I, so 18M_B = −810 and M_B = −45 kN m.
  3. Reactions: R_A = 45 + (−45)/6 = 37.5 kN; R_C = 0 + (−45)/6 = −7.5 kN (downward, a hold-down force); R_B = 90 − 37.5 + 7.5 = 60 kN.
  4. With equal I: 2M_B(12) = −810, M_B = −33.75 kN m and R_C = −5.63 kN.
  5. The stiffer unloaded span attracts more moment to B, and the far end C tends to lift: it needs a hold-down or enough dead load on BC.

Answer. M_B = −45 kN m (−33.75 kN m with equal I); R_A = 37.5, R_B = 60 kN, R_C = 7.5 kN downward

Step-by-step procedure

  1. Number the supports; note known moments (zero at simple ends, statics at overhangs) and add a zero-length span at each fixed end.
  2. Compute the free-diagram load term 6Ax̄/L for each loaded span (standard results), dividing by I if the spans differ.
  3. Write one three-moment equation for each interior support and each fixed end, and solve for the unknown support moments.
  4. Find reactions span by span from R = R₀ + (moment difference)/L and add the parts at each support; check that the reactions sum to the total load.
  5. Draw the final moment diagram as free diagram plus closing line; find span maxima at zero shear.

Site notes

  • The largest moments in a continuous beam or slab are usually the hogging moments over interior supports; top steel there is critical and must not be displaced by foot traffic before concreting.
  • A short end span next to a long loaded span can lift off its support; check for uplift and provide hold-down or bearing restraint where the reaction can reverse.
  • Continuous beams are sensitive to support stiffness: a column that shortens or a bearing that compresses more than its neighbours changes the moments (lesson 3.4).
  • Loading only alternate spans (pattern loading) gives larger span moments than full loading; the equation handles any pattern, span by span.
Common mistakes
  • Measuring x̄ from the wrong end: it must be from the far (outer) support of each span.
  • Forgetting the factor 2 on the middle moment, or omitting the I values when spans differ.
  • Treating a fixed end as simply supported (M = 0) instead of adding the zero-length span.
  • Using the simple-span reactions without the (M difference)/L correction.
  • Mixing hogging-positive and sagging-positive signs within one solution.
Quick check

For equal spans with a full uniform load and simple ends, the interior support moments are −wl²/8 for two spans and −wl²/10 for three spans; an answer far from these for nearly equal spans signals an error. Valid for constant EI and supports at the same level.

Summary

  • Three-moment equation: slope continuity over each interior support links three support moments.
  • Load terms: wL³/4, 3PL²/8, Pab(L + a)/L, with x̄ from the far support.
  • Fixed ends use a zero-length imaginary span; overhang moments come from statics.
  • Reactions: simple-span value plus moment difference over the span.
  • Stiffer spans attract more moment; short end spans can lift.

Practice questions

Tap a question to see the answer.

1Two equal spans of 4 m carry 10 kN/m throughout. Find the support moment and the middle reaction.

2M_B(8) = −2 × 10 × 64/4 = −320, M_B = −20 kN m; R_B = 2(20 + 20/4) = 50 kN.

2Three equal spans of 6 m carry 10 kN/m throughout, simple ends. Find M_B and M_C.

24M_B + 6M_C = −1080 and 6M_B + 24M_C = −1080; by symmetry 30M_B = −1080, M_B = M_C = −36 kN m (= −wl²/10).

3Two spans of 5 m each carry a central point load of 40 kN on each span. Find M_B.

2M_B(10) = −2 × 3 × 40 × 25/8 = −750, M_B = −37.5 kN m (= −3PL/16).

4Use the three-moment equation with imaginary spans to find the end moments of a single fixed beam of 6 m under 20 kN/m.

Both ends fixed: 2M_A L + M_B L = −wL³/4 and M_A L + 2M_B L = −wL³/4; with M_A = M_B, 3ML = −wL³/4, so M = −wL²/12 = −60 kN m.

5In Example 1, the 60 kN load in span BC is moved to 1 m from C. Find M_B.

Load term with a = 1 m from the far support C, b = 3 m: Pab(L + a)/L = 60 × 1 × 3 × 5/4 = 225; 20M_B = −1080 − 225, M_B = −65.25 kN m.

6A beam ABCD has spans AB = BC = 4 m on simple supports A, B, C and an overhang CD of 2 m carrying 10 kN at D; no other load. Find M_C and M_B.

M_C = −10 × 2 = −20 kN m from statics. At B: 2M_B(8) + (−20)(4) = 0, so M_B = +5 kN m (sagging): the overhang load lifts span AB slightly.

References

Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.

  • R. C. Hibbeler, Structural Analysis, Pearson, 10th edition, 2018.
  • C. S. Reddy, Basic Structural Analysis, Tata McGraw Hill (now McGraw Hill Education (India)), 3rd edition, 2011.
  • D. Menon, Structural Analysis, Narosa Publishing House, 2nd edition.
  • B. J. Goodno, J. M. Gere, Mechanics of Materials, Cengage Learning, 9th edition, 2018.
Suggest a correction

If something on this page is wrong, tell the editor. Your message is sent privately and is not published.

Sent privately to the Indiacon editor; not published.