Indiacon CivilSubscribe

Textbook › Strength of Materials › Chapter 1 › Lesson 1.1

1.1 Stress, strain and Hooke's law

Strength of Materials Chapter 1: Simple stress and strain Under review — not yet three-checked Author: Indiacon

Learning objectives

After this lesson you should be able to:

  • Define normal, shear and bearing stress as internal force per unit area, and compute average values from a free-body cut.
  • Define normal strain and shear strain, and relate them to stress through Hooke's law σ = E ε and τ = G γ.
  • Derive and use the elongation of a uniform bar δ = PL/(AE) and its axial stiffness k = AE/L for civil members such as hangers, ties and bolts.

Theory

Engineering mechanics treats members as rigid; strength of materials asks what happens inside them. When a steel hanger carries a load, every cross-section of the rod must transmit that load to the part above. Cut the rod anywhere and the internal force on the cut face balances the load below it. Stress is this internal force spread over the area that carries it: force per unit area, measured in N/mm² (MPa). Stress, not force, decides whether a material yields or breaks, because a thick bar and a thin bar of the same steel fail at the same stress but at very different loads.

Stress has two kinds of component. Normal stress σ acts perpendicular to the cut face and either pulls the material apart (tension, taken positive) or pushes it together (compression). Shear stress τ acts along the face and tends to slide one part over the other, as in a bolt that joins two plates or a rivet in a lap joint. Where two bodies press on each other, such as a bolt shank on the side of its hole or a column base plate on a pedestal, the contact pressure is called bearing stress; it is a compressive normal stress calculated on the projected contact area.

PPσ = P / ALδγτ = G γσ = E ε, δ = PL / (AE)Indiacon original, not to scale
Figure 1.1: Axial stress, elongation and shear strain in a bar. Indiacon original, not to scale.

Strain describes deformation without reference to the size of the member. Normal strain ε is the change in length divided by the original length, a dimensionless ratio often quoted in microstrain (10⁻⁶) or mm per metre. Shear strain γ is the change, in radians, of an angle that was originally a right angle. Because strain is a ratio, a 3 m rod and a 30 m rod of the same steel at the same stress have the same strain, but the long rod stretches ten times as much.

For most structural materials at working loads, stress is proportional to strain. Robert Hooke observed this proportionality for springs in the seventeenth century; for a material it is written σ = E ε, where the modulus of elasticity E is a property of the material, about 200 000 N/mm² for steel and 20 000 to 35 000 N/mm² for normal concrete. In shear the corresponding law is τ = G γ, with G the shear modulus. Within this linear elastic range the member returns to its original length when the load is removed, and the elongation of a bar follows directly: δ = PL/(AE). Saint-Venant's principle tells us that the simple formula σ = P/A is accurate a short distance (about one width) away from where the load is applied; close to bolts, holes and bearing plates the stress is locally higher.

Derivation

  1. Cut a straight bar of cross-sectional area A, carrying an axial load P, by a plane perpendicular to its axis. Equilibrium of the lower part requires the internal force on the cut to equal P.
  2. If the stress is uniform over the cut (load through the centroid, far from the ends), the internal force is σ A, so σ = P/A.
  3. A bolt in single shear transmits the force V across one plane of area A_b: average τ = V/A_b. In double shear two planes share the force: τ = V/(2 A_b).
  4. Bearing stress on a plate of thickness t from a bolt of diameter d: σ_b = P/(d t), using the projected area d × t.
  5. Normal strain: a bar of length L that lengthens by δ has ε = δ/L. Shear strain: a right angle that becomes (π/2 − γ) has shear strain γ.
  6. Complementary shear: take a small element dx × dy of thickness t with shear τ on the vertical faces. Moments about a corner give (τ dy t) dx = (τ′ dx t) dy, so τ′ = τ: shear stresses on perpendicular faces are always equal.
  7. Hooke's law σ = E ε with σ = P/A and ε = δ/L gives P/A = E δ/L, so δ = PL/(AE).
  8. Rearranged as P = (AE/L) δ, the bar behaves as a spring of axial stiffness k = AE/L (N/mm or kN/m).
Formulas, symbols and SI units
  • Normal stress σ = P/A (P in N, A in mm², σ in N/mm² = MPa)
  • Average shear stress τ = V/A (single shear), τ = V/(2A) (double shear)
  • Bearing stress σ_b = P/(d t) (d bolt diameter, t plate thickness, mm)
  • Normal strain ε = δ/L (dimensionless); shear strain γ in radians
  • Hooke's law σ = E ε; τ = G γ (E, G in N/mm²)
  • Elongation δ = PL/(AE) (mm when P in N, L in mm, A in mm², E in N/mm²)
  • Axial stiffness k = AE/L (N/mm)
  • 1 N/mm² = 1 MPa = 1000 kN/m²; area of a circle A = π d²/4
Assumptions and limits
  • Load is axial and passes through the centroid of the cross-section, so stress is uniform; eccentric load adds bending (Chapter 9).
  • Material is homogeneous, isotropic and linear elastic; the formulas stop applying beyond the limit of proportionality (lesson 1.2).
  • Deformations are small, so the original area and length are used (engineering stress and strain).
  • Average shear and bearing stresses are used for bolts and pins; the real distribution is uneven and design codes account for it.
  • Sections are far from abrupt changes of section, holes and load points (Saint-Venant's principle); near them stress concentrations occur.
  • Compression members are short enough not to buckle (buckling is Chapter 9).

Codes and standards

Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.

  • No design code governs the definitions of stress and strain or Hooke's law; they follow from equilibrium and the measured behaviour of materials.
  • IS 800:2007 cl. 2.2.4.1 takes the modulus of elasticity of structural steel of any grade as E = 2.0 × 10⁵ N/mm², the value used in the examples here.
  • IS 800:2007 cl. 2.2.4.2 states that yield stress, ultimate stress and elongation of structural steel are found by tensile tests to IS 1608.
  • Side by side: EN 1993-1-1 takes E = 210 000 N/mm² for structural steel; tensile testing of metals is covered by ISO 6892-1 and ASTM E8/E8M. Each is used within its own system and they are not ranked here.

Worked examples

Example 1 (site style)

Problem. A steel hanger rod of 20 mm diameter and 3 m length supports a walkway and carries 50 kN in tension. Take E = 2.0 × 10⁵ N/mm². Find the stress, the strain and the elongation of the rod.

  1. A = π × 20² / 4 = 314.16 mm².
  2. σ = P/A = 50 000 / 314.16 = 159.15 N/mm² (tension).
  3. ε = σ/E = 159.15 / 200 000 = 7.958 × 10⁻⁴ (about 0.8 mm per metre).
  4. δ = ε L = 7.958 × 10⁻⁴ × 3000 = 2.387 mm.
  5. Check with δ = PL/(AE) = 50 000 × 3000 / (314.16 × 200 000) = 2.387 mm.

Answer. σ = 159.2 N/mm²; ε = 7.96 × 10⁻⁴; δ = 2.39 mm

Example 2 (exam style)

Problem. A 20 mm bolt connects a 12 mm gusset plate between two cover plates (double shear) and transmits 60 kN. Find the average shear stress in the bolt and the bearing stress on the gusset plate.

  1. Shank area A_b = π × 20² / 4 = 314.16 mm².
  2. Double shear: τ = V/(2 A_b) = 60 000 / (2 × 314.16) = 95.49 N/mm².
  3. Bearing on the 12 mm gusset: projected area d t = 20 × 12 = 240 mm².
  4. σ_b = 60 000 / 240 = 250 N/mm².
  5. The bearing stress is far higher than the shear stress, which is why thin plates often fail by hole elongation before the bolt shears.

Answer. τ = 95.5 N/mm²; σ_b = 250 N/mm²

Example 3 (laboratory style)

Problem. In a tensile test a 12 mm diameter steel specimen is fitted with an extensometer of 50 mm gauge length. At a load of 20 kN the extension is 0.044 mm. Find the modulus of elasticity.

  1. A = π × 12² / 4 = 113.10 mm².
  2. σ = 20 000 / 113.10 = 176.84 N/mm².
  3. ε = 0.044 / 50 = 8.8 × 10⁻⁴.
  4. E = σ/ε = 176.84 / 8.8 × 10⁻⁴ = 200 953 N/mm² ≈ 2.01 × 10⁵ N/mm².
  5. The result agrees with the nominal steel value of 2.0 × 10⁵ N/mm², a useful check that the extensometer and load cell are reading correctly.

Answer. E ≈ 2.01 × 10⁵ N/mm²

Step-by-step procedure

  1. Draw the member and cut it at the section of interest; find the internal force (axial force, shear force) by equilibrium.
  2. Identify the area that carries it: net cross-section for normal stress, shear planes for bolts and pins, projected area d × t for bearing.
  3. Compute stress = force / area in consistent units (N and mm give N/mm²).
  4. Find strain from ε = σ/E (or γ = τ/G) and elongation from δ = ε L = PL/(AE).
  5. Check that the stress is below the limit of proportionality and that the member is not near a hole or load point where local stress is higher.

Site notes

  • Hanger rods, tie rods and anchor bolts are checked by stress and by stretch: a long tie can satisfy stress yet stretch enough to sag a walkway or open joints.
  • On a bolted joint, look at the hole edges after load tests; elongated holes show bearing distress, not bolt shear.
  • Strain gauges and vibrating-wire gauges measure strain, not stress; the stress is inferred with E, so the right modulus for the material matters.
  • Mark load units clearly on site calculations: a 50 t jack force is about 490 kN, not 50 kN.
Common mistakes
  • Using diameter in place of area, or forgetting the π/4 in A = π d²/4.
  • Taking double shear as single shear and so doubling the bolt shear stress (or the reverse).
  • Mixing units: kN with mm² gives kN/mm², which is 1000 times N/mm².
  • Applying σ = P/A right next to holes and point loads, where local stress is much higher.
  • Treating strain as having units; it is a ratio (mm/mm).
Quick check

Steel in the elastic range: elongation in mm ≈ stress in N/mm² × length in m ÷ 200 (for example 150 N/mm² over 4 m gives 3 mm). Valid below the limit of proportionality only.

Summary

  • Stress is internal force per unit area: σ = P/A, τ = V/A, bearing σ_b = P/(d t).
  • Strain is deformation per unit length (ε) or change of a right angle (γ).
  • Hooke's law: σ = E ε, τ = G γ; steel E = 2.0 × 10⁵ N/mm².
  • Uniform bar: δ = PL/(AE); stiffness k = AE/L.

Practice questions

Tap a question to see the answer.

1A 16 mm bar carries an axial tension of 30 kN. Find the stress.

A = 201.06 mm²; σ = 30 000 / 201.06 = 149.2 N/mm².

2A 2 m long member has a strain of 0.0005. Find its change in length.

δ = 0.0005 × 2000 = 1.0 mm.

3What axial load gives an average compressive stress of 5 N/mm² on a 300 mm × 300 mm pedestal?

P = 5 × 90 000 = 450 000 N = 450 kN.

4An elastomeric bearing pad 300 mm × 400 mm in plan with 50 mm total rubber thickness carries a horizontal force of 30 kN. Take G = 1.0 N/mm². Find the shear stress, shear strain and horizontal movement of the top.

τ = 30 000 / 120 000 = 0.25 N/mm²; γ = τ/G = 0.25 rad; movement = 0.25 × 50 = 12.5 mm.

5Why is engineering stress calculated on the original area and not the current area?

For small strains the area hardly changes, the original area is known in advance, and design limits are defined on that basis; the true-stress correction matters only at large plastic strains (lesson 1.2).

6A 25 mm steel tie 4 m long must not stretch more than 2 mm. Taking E = 2.0 × 10⁵ N/mm², find the largest load and the stress at that load.

P = δ A E / L = 2 × 490.87 × 200 000 / 4000 = 49 087 N ≈ 49.1 kN; σ = 100 N/mm².

References

Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.

  • B. J. Goodno, J. M. Gere, Mechanics of Materials, Cengage Learning, 9th edition, 2018.
  • R. C. Hibbeler, Mechanics of Materials, Pearson, 10th edition, 2016.
  • F. P. Beer, E. R. Johnston, J. T. DeWolf, D. F. Mazurek, Mechanics of Materials, McGraw Hill, 8th edition, 2020.
  • E. P. Popov, Engineering Mechanics of Solids, Prentice Hall, 2nd edition, 1998.
Suggest a correction

If something on this page is wrong, tell the editor. Your message is sent privately and is not published.

Sent privately to the Indiacon editor; not published.