6.1 Torsion of circular shafts
After this lesson you should be able to:
- Derive the torsion equation T/J = τ/r = G θ/L for a circular shaft from geometry of deformation, Hooke's law in shear and equilibrium.
- Compute the polar second moment of area, maximum shear stress and angle of twist of solid and hollow circular shafts.
- Solve shafts fixed at both ends and explain why hollow sections carry torque more efficiently than solid ones of the same weight.
Theory
Torsion is twisting of a member about its own axis by a torque, a couple acting in the plane of the cross-section. In civil works it appears in pump and hoist shafts, drill rods and Kelly bars of piling rigs, tubular poles carrying signs to one side, and in beams that support loads off their centre line. This chapter treats members of circular cross-section, solid or hollow, for which an exact elementary theory exists. Non-circular sections warp and need a different treatment.
Experiments with circular shafts show that plane cross-sections stay plane and do not distort in their own plane; each section simply rotates as a rigid disc about the axis. A straight line drawn along the surface becomes a helix. If one end of a shaft of length L turns through an angle θ relative to the other, a fibre at radius r is displaced by r θ around the circumference, and the shear strain there is γ = r θ/L. Strain therefore grows linearly from zero at the axis to its largest value at the outer surface.
With Hooke's law in shear, τ = G γ, the shear stress also grows linearly with radius: τ = G θ r/L. Each element of area dA at radius r carries a force τ dA with a moment τ r dA about the axis, and these add up to the applied torque. The sum ∫ r² dA is the polar second moment of area J, so T = G θ J/L. Combining the two results gives the torsion equation T/J = τ/r = G θ/L, the twin of the bending equation of lesson 3.1.
Because stress is largest at the outside and zero at the centre, the material near the axis does little work. Removing it, as in a hollow tube, cuts weight much more than it cuts strength or stiffness. The product G J is the torsional rigidity, and G J/L is the torque needed for one radian of twist. When a shaft is held at both ends and loaded between them, equilibrium alone cannot split the torque between the two ends; the extra condition is that the total twist from end to end is zero, exactly as for axially loaded bars held at both ends in lesson 1.4.
Derivation
- Geometry: a fibre at radius r on a shaft of length L whose ends twist through θ relative to each other moves r θ around the circumference, so γ = r θ/L (small angles).
- Material: τ = G γ = G θ r/L, so τ varies linearly with r.
- Equilibrium: T = ∫ τ r dA = (G θ/L) ∫ r² dA = G θ J/L.
- Torsion equation: T/J = τ/r = G θ/L.
- Solid shaft of diameter d: J = ∫₀^(d/2) r² (2π r) dr = π d⁴/32, so τ_max = T (d/2)/J = 16 T/(π d³).
- Hollow shaft, outer diameter D, inner d: J = π (D⁴ − d⁴)/32, τ_max = 16 T D/(π (D⁴ − d⁴)); stress at the inner surface = τ_max × d/D.
- Polar modulus Z_p = J/R, so τ_max = T/Z_p; angle of twist θ = T L/(G J) in radians.
- Shaft fixed at both ends with torque T at distance a from end A and b from end B (a + b = L): T_A + T_B = T and the twist of A to C equals the twist of B to C, T_A a/(G J) = T_B b/(G J). Hence T_A = T b/L and T_B = T a/L.
Torsion equation: T/J = τ/r = G θ/LSolid: J = π d⁴/32 (mm⁴), τ_max = 16 T/(π d³) (N/mm²)Hollow: J = π (D⁴ − d⁴)/32, τ_max = 16 T D/(π (D⁴ − d⁴))Angle of twist: θ = T L/(G J) (rad); degrees = rad × 180/πTorsional rigidity G J (N·mm²/rad); torsional stiffness G J/LFixed at both ends, torque T at a from A: T_A = T b/L, T_B = T a/LUnits: T in N·mm, d in mm, G in N/mm² (steel about 80 000 N/mm²)
- The shaft is straight, of circular cross-section (solid or hollow), and of uniform material obeying Hooke's law in shear.
- Cross-sections remain plane and radii remain straight; this holds exactly for circular sections only. Rectangular and open sections warp, and the formulas here do not apply to them.
- Twist is small, so γ = r θ/L and the shaft length does not change.
- Stresses stay below the shear proportional limit; yielding, fatigue and stress concentration at keyways, shoulders and holes are separate checks.
- Limits: the torque is applied at the ends or at discrete sections away from which the stress pattern has settled (Saint-Venant's principle).
Codes and standards
Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.
- The torsion of circular shafts is mechanics; no design code governs the derivation or the formulas in this lesson.
- Shafts of pumps, hoists and drives are machine elements, designed by mechanical engineering practice and supplied by manufacturers; civil engineers mainly check supports, couplings and foundations for the torque they transmit.
- Side by side, not ranked: the Indian, European (EN 1993-1-1) and American (AISC 360) steel codes all build their torsion checks for members on the elastic shear stress distribution described here, each with its own resistance factors; reinforced concrete torsion in IS 456:2000 and other concrete codes uses empirical design rules, introduced in lesson 6.3.
Worked examples
Problem. A solid steel shaft of a construction hoist drive is 60 mm in diameter and 1.5 m long between the motor coupling and the drum. It transmits a torque of 4 kN·m. G = 80 000 N/mm². Find the maximum shear stress and the angle of twist.
- J = π × 60⁴/32 = 1.272 × 10⁶ mm⁴.
- τ_max = T r/J = 4 × 10⁶ × 30/1.272 × 10⁶ = 94.3 N/mm² (check: 16 T/(π d³) = 94.3 N/mm²).
- θ = T L/(G J) = 4 × 10⁶ × 1500/(80 000 × 1.272 × 10⁶) = 0.0589 rad.
- θ = 0.0589 × 180/π = 3.38°.
Answer. τ_max = 94.3 N/mm²; θ = 0.0589 rad = 3.38°
Problem. A rotary drilling rig for bored piles needs a drive rod. Compare a hollow steel rod of 80 mm outer and 60 mm inner diameter with a solid rod of the same cross-sectional area. The allowable shear stress is 80 N/mm². Find the torque each can carry.
- Area of the hollow rod = π (80² − 60²)/4 = π × 2800/4 mm²; a solid rod of the same area has d = √2800 = 52.9 mm.
- Hollow: J = π (80⁴ − 60⁴)/32 = 2.749 × 10⁶ mm⁴; T = τ J/R = 80 × 2.749 × 10⁶/40 = 5.50 × 10⁶ N·mm = 5.50 kN·m.
- Solid: T = π d³ τ/16 = π × 52.9³ × 80/16 = 2.33 × 10⁶ N·mm = 2.33 kN·m.
- The hollow rod carries 2.36 times the torque for the same weight of steel, because its material sits where the stress is high.
Answer. Hollow 5.50 kN·m; solid 2.33 kN·m; ratio 2.36
Problem. A sluice gate operating shaft 1.8 m long, 50 mm in diameter, is held against rotation at both ends A and B. A torque of 3 kN·m is applied by the gear at C, 0.6 m from A. G = 80 000 N/mm². Find the end torques, the maximum shear stress and the rotation at C.
- Compatibility: twist of AC equals twist of CB, so T_A × 0.6 = T_B × 1.2; equilibrium: T_A + T_B = 3 kN·m.
- T_A = 3 × 1.2/1.8 = 2.0 kN·m and T_B = 3 × 0.6/1.8 = 1.0 kN·m; the shorter, stiffer segment takes more torque.
- J = π × 50⁴/32 = 6.136 × 10⁵ mm⁴. τ_max (segment AC) = 16 × 2 × 10⁶/(π × 50³) = 81.5 N/mm².
- Rotation at C = T_A × a/(G J) = 2 × 10⁶ × 600/(80 000 × 6.136 × 10⁵) = 0.0244 rad = 1.40°.
Answer. T_A = 2.0 kN·m, T_B = 1.0 kN·m; τ_max = 81.5 N/mm²; φ_C = 1.40°
Step-by-step procedure
- Draw the shaft with all applied torques and supports, and find the internal torque in each segment by equilibrium (and compatibility if both ends are held).
- Compute J for each segment: π d⁴/32 for solid, π (D⁴ − d⁴)/32 for hollow.
- Find τ_max = T R/J in each segment and compare with the allowable shear stress.
- Find the twist of each segment, T L/(G J), and add them with signs for the total twist.
- Check stress concentrations at keyways, shoulders and couplings separately.
Site notes
- Piling rig Kelly bars and drill rods are hollow or built-up sections because they must carry large torque with limited weight on the mast.
- Vertical turbine pump shafts at river intakes and tube wells are long; their angle of twist and alignment matter as much as stress.
- Sign posts with boards to one side and street light poles with long arms are twisted by wind on the board; tubular poles resist this well, while open sections such as channels twist easily.
- Couplings, keys and bolts must carry the same torque as the shaft; a strong shaft with a weak coupling still fails.
- Using the bending formula I = π d⁴/64 instead of J = π d⁴/32.
- Mixing kN·m with N·mm, or giving the angle of twist in degrees inside the formula instead of radians.
- Applying T/J = τ/r to rectangular or open sections.
- Assuming both ends of a doubly fixed shaft share the torque equally regardless of where it is applied.
- Taking the stress at the inner surface of a hollow shaft as zero.
τ_max = 16 T/(π d³) for a solid shaft and θ = T L/(G J). Doubling the diameter makes a solid shaft 8 times stronger and 16 times stiffer in torsion. For a quick check, 1 kN·m on a 50 mm solid shaft gives about 41 N/mm².
Summary
- Plane sections of a circular shaft stay plane and rotate; shear strain and stress grow linearly with radius.
- T/J = τ/r = G θ/L, with J = π d⁴/32 for a solid shaft and π (D⁴ − d⁴)/32 for a hollow one.
- Angle of twist θ = T L/(G J) in radians; G J is the torsional rigidity.
- Hollow sections carry more torque per unit weight than solid ones.
- Shafts fixed at both ends need compatibility: T_A = T b/L and T_B = T a/L.
Practice questions
Tap a question to see the answer.
1Find J for a solid shaft of 100 mm diameter.
J = π × 100⁴/32 = 9.82 × 10⁶ mm⁴.
2What torque can a solid 40 mm shaft carry if the allowable shear stress is 60 N/mm²?
T = π d³ τ/16 = π × 64 000 × 60/16 = 7.54 × 10⁵ N·mm = 0.754 kN·m.
3A 50 mm solid shaft 2 m long carries 1.5 kN·m; G = 80 000 N/mm². Find the angle of twist.
θ = T L/(G J) = 1.5 × 10⁶ × 2000/(80 000 × 6.136 × 10⁵) = 0.0611 rad = 3.50°.
4A hollow shaft of 100 mm outer and 80 mm inner diameter carries 10 kN·m. Find the shear stress at the outer and inner surfaces.
J = π (100⁴ − 80⁴)/32 = 5.80 × 10⁶ mm⁴. Outer: 10 × 10⁶ × 50/5.80 × 10⁶ = 86.3 N/mm². Inner: 86.3 × 40/50 = 69.0 N/mm².
5Find the diameter of a solid shaft to carry 2 kN·m with an allowable shear stress of 50 N/mm².
d = (16 T/(π τ))^(1/3) = (16 × 2 × 10⁶/(π × 50))^(1/3) = 58.8 mm; adopt 60 mm.
6By what factors do the torque capacity and the torsional stiffness of a solid shaft change if its diameter is doubled?
Capacity varies with d³, so it rises 8 times; stiffness G J/L varies with d⁴, so it rises 16 times.
References
Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.
- B. J. Goodno, J. M. Gere, Mechanics of Materials, Cengage Learning, 9th edition, 2018.
- R. C. Hibbeler, Mechanics of Materials, Pearson, 10th edition, 2016.
- F. P. Beer, E. R. Johnston, J. T. DeWolf, D. F. Mazurek, Mechanics of Materials, McGraw Hill, 8th edition, 2020.
- E. P. Popov, Engineering Mechanics of Solids, Prentice Hall, 2nd edition, 1998.