Indiacon CivilSubscribe

Textbook › Strength of Materials › Chapter 5 › Lesson 5.1

5.1 Differential equation of the elastic curve

Strength of Materials Chapter 5: Deflection of beams Under review — not yet three-checked Author: Indiacon

Learning objectives

After this lesson you should be able to:

  • Derive the differential equation of the elastic curve, EI y″ = M, from the moment-curvature relation of simple bending, and state the sign convention it depends on.
  • Write the correct boundary conditions for simply supported, fixed, free and propped ends, and use them to fix the constants of integration.
  • Find the slope and deflection of standard cantilevers and simply supported beams, and compare a computed deflection with the serviceability limits that codes set.

Theory

A beam that is strong enough can still be unfit for use. A floor that sags visibly, cracks the plaster on the ceiling below, makes doors jam in partitions or bounces when people walk on it has failed in service even though no member has broken. Designers therefore check two things: strength (stresses, lessons 3 and 4) and stiffness (deflections, this chapter). This lesson builds the basic tool for the stiffness check: an equation linking the shape of the bent beam to the bending moment in it.

Lesson 3.1 showed that a beam in bending curves into an arc whose radius R at any section is given by 1/R = M/(E I). The product E I is the flexural rigidity: E is a property of the material and I a property of the shape of the cross-section. A large E I means a small curvature for a given moment. The line taken up by the neutral axis after loading is called the elastic curve, and its vertical movement y at each point is the deflection.

wδ (deflection)θxyE I y″ = M (sagging M positive)1/R = M/(E I) ≈ y″ for small slopesIndiacon original, not to scale
Figure 5.1: Elastic curve of a simply supported beam: with y upward and sagging moment positive, the curvature y″ equals M/(E I); deflection δ and end slope θ follow by integration. Indiacon original, not to scale.

Geometry links curvature to the shape of a curve y(x): the exact curvature is y″/(1 + y′²)^(3/2). In real beams the slope y′ is tiny, usually well under 0.01 radian, so y′² is negligible and the curvature is simply y″. Putting the two statements together gives E I y″ = M. Because dM/dx = V and dV/dx = −w (lesson 2.4), the same equation can be differentiated to E I y‴ = V and E I y⁗ = −w, so the load, shear, moment, slope and deflection form one chain linked by integration.

Integrating E I y″ = M once gives the slope, and again gives the deflection. Each integration brings in a constant, and these are found from what is known at the supports: the boundary conditions. A simple support or roller fixes the deflection (y = 0) but leaves the beam free to rotate. A fixed end stops both deflection and rotation (y = 0, y′ = 0). A free end carries no moment and no shear. With these, the deflections of the standard cases follow directly; for example, a simply supported beam under a uniformly distributed load deflects 5 w L⁴/(384 E I) at midspan, and a cantilever with a load at its tip deflects P L³/(3 E I).

Derivation

  1. Sign convention used in this chapter: x is measured along the beam from the left end, y is the deflection measured upward (so a downward deflection is negative), and a sagging bending moment (tension at the bottom) is positive.
  2. From lesson 3.1, an element of the beam bent by a moment M takes up a radius of curvature R with 1/R = M/(E I).
  3. For a plane curve y(x), the curvature is κ = y″/(1 + y′²)^(3/2). With the convention above, a sagging beam is concave upward, so y″ is positive when M is positive and the signs agree.
  4. Small-slope approximation: if y′ is 0.01 rad, y′² = 0.0001 and (1 + y′²)^(3/2) differs from 1 by only 0.015%. So κ ≈ y″.
  5. Hence E I d²y/dx² = M(x), the differential equation of the elastic curve.
  6. Differentiating with E I constant, and using dM/dx = V and dV/dx = −w (w downward): E I y‴ = V and E I y⁗ = −w.
  7. Integrate once: E I y′ = ∫M dx + C₁ (slope). Integrate again: E I y = ∬M dx dx + C₁ x + C₂ (deflection).
  8. Simply supported beam, uniformly distributed load w, span L: M = w L x/2 − w x²/2. Then E I y′ = w L x²/4 − w x³/6 + C₁ and E I y = w L x³/12 − w x⁴/24 + C₁ x + C₂.
  9. Boundary conditions y(0) = 0 gives C₂ = 0; y(L) = 0 gives C₁ = −w L³/24.
  10. At midspan, x = L/2: E I y = w L⁴/96 − w L⁴/384 − w L⁴/48 = −5 w L⁴/384, so δ_max = 5 w L⁴/(384 E I) downward. The end slope is θ = w L³/(24 E I).
  11. Cantilever fixed at x = 0 with a load P at the free end x = L: M = −P (L − x). Integrating with y(0) = 0 and y′(0) = 0 gives E I y = −P (L x²/2 − x³/6), so at the tip δ = P L³/(3 E I) and θ = P L²/(2 E I).
Formulas, symbols and SI units
  • Moment-curvature: 1/R = M/(E I) (1/mm)
  • Differential equation of the elastic curve: E I d²y/dx² = M (N·mm)
  • Shear and load: E I y‴ = V; E I y⁗ = −w
  • Simply supported, uniformly distributed load: δ = 5 w L⁴/(384 E I); θ_end = w L³/(24 E I)
  • Simply supported, central point load: δ = P L³/(48 E I); θ_end = P L²/(16 E I)
  • Cantilever, tip load: δ = P L³/(3 E I); θ = P L²/(2 E I)
  • Cantilever, uniformly distributed load: δ = w L⁴/(8 E I); θ = w L³/(6 E I)
  • Units: w in N/mm (1 kN/m = 1 N/mm), P in N, L in mm, E in N/mm², I in mm⁴, δ in mm, θ in radians; or kN, m and kN·m² throughout
Assumptions and limits
  • The material is linear elastic and obeys Hooke's law, with the same E in tension and compression.
  • Deflections and slopes are small, so y′² is neglected in the curvature and the beam's length along the curve equals its horizontal span.
  • Plane sections remain plane (lesson 3.1), and deflection due to shear deformation is neglected; this is accurate for slender beams with span more than about ten times the depth, and underestimates deflection of short, deep beams, timber beams with low shear modulus and beams with thin webs.
  • The beam is prismatic unless E I is written as a function of x, and it bends in a plane of symmetry without twisting.
  • Limits: the method does not cover large deflections (cables, very thin strips), yielded steel, cracked or creeping concrete unless an effective E I is used, or dynamic effects such as vibration.

Codes and standards

Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.

  • The elastic curve equation is mechanics; codes do not change it, but they set how much deflection is acceptable and how E I is to be taken.
  • IS 456:2000 cl. 23.2: for reinforced concrete floors, roofs and other horizontal members, the final deflection due to all loads, including the effects of temperature, creep and shrinkage, should not normally exceed span/250, and the deflection occurring after partitions are built and finishes applied should not normally exceed span/350 or 20 mm, whichever is less. Both checks apply. Concrete deflection must use a cracked, long-term stiffness, which that code covers separately.
  • IS 800:2007 cl. 5.6.1 refers to Table 6 of that code for recommended deflection limits. For a simply supported floor or roof beam in a non-industrial building under live load, Table 6 gives span/300 where the supported elements are not susceptible to cracking and span/360 where they are, such as plastered or brittle finishes. A published correction to cl. 5.6.1 states that the live load for this check includes all post-construction loads, including superimposed dead loads.
  • Side by side, not ranked: EN 1990 with EN 1992-1-1 and EN 1993-1-1, ACI 318, and AISC 360 with its serviceability guidance each give span-based deflection limits that depend on the member's use and on what it supports; their values and load combinations differ, so a design is checked against the code it is designed to.

Worked examples

Example 1 (site style: steel floor beam deflection check)

Problem. A simply supported steel floor beam in an office spans 6 m and carries an imposed (post-construction) load of 12 kN/m. E = 200 000 N/mm² and I = 8.0 × 10⁷ mm⁴ (problem data). Find the midspan deflection under this load and compare it with the IS 800 floor-beam limits.

  1. E I = 200 000 × 8.0 × 10⁷ = 1.6 × 10¹³ N·mm² = 16 000 kN·m².
  2. δ = 5 w L⁴/(384 E I) = 5 × 12 × 6⁴/(384 × 16 000) = 77 760/6 144 000 = 0.01266 m = 12.66 mm.
  3. Limit span/300 = 6000/300 = 20.0 mm (finishes not susceptible to cracking); span/360 = 16.7 mm (brittle finishes).
  4. 12.66 mm is below both limits, so the beam is stiff enough for either kind of finish.
  5. End slope: θ = w L³/(24 E I) = 12 × 216/(24 × 16 000) = 6.75 × 10⁻³ rad.

Answer. δ = 12.66 mm, within span/300 (20.0 mm) and span/360 (16.7 mm)

Example 2 (cantilever bracket with a tip load)

Problem. A steel cantilever bracket 1.5 m long carries a 10 kN load at its free end. E = 200 000 N/mm², I = 2.0 × 10⁷ mm⁴. Find the tip deflection and the slope at the tip.

  1. E I = 200 000 × 2.0 × 10⁷ = 4.0 × 10¹² N·mm².
  2. δ = P L³/(3 E I) = 10 × 10³ × 1500³/(3 × 4.0 × 10¹²) = 3.375 × 10¹³/1.2 × 10¹³ = 2.81 mm.
  3. θ = P L²/(2 E I) = 10 × 10³ × 1500²/(2 × 4.0 × 10¹²) = 2.81 × 10⁻³ rad.
  4. Check of units: N × mm³/(N/mm² × mm⁴) = mm, as it should be.

Answer. δ_tip = 2.81 mm; θ_tip = 2.81 × 10⁻³ rad

Example 3 (exam style: derive the elastic curve of a cantilever under uniform load)

Problem. A timber canopy joist 75 mm × 200 mm is built in at one end and projects 2 m, carrying 1.5 kN/m. E = 10 000 N/mm². Derive the elastic curve by double integration and find the tip deflection and slope.

  1. Measure x from the free end. M = −w x²/2 (hogging), so E I y″ = −w x²/2.
  2. E I y′ = −w x³/6 + C₁; at the fixed end x = L, y′ = 0, so C₁ = w L³/6.
  3. E I y = −w x⁴/24 + w L³ x/6 + C₂; at x = L, y = 0, so C₂ = w L⁴/24 − w L⁴/6 = −w L⁴/8.
  4. At the tip, x = 0: y = −w L⁴/(8 E I) and y′ = w L³/(6 E I).
  5. I = 75 × 200³/12 = 5.0 × 10⁷ mm⁴; E I = 5.0 × 10¹¹ N·mm².
  6. δ = 1.5 × 2000⁴/(8 × 5.0 × 10¹¹) = 2.4 × 10¹³/4.0 × 10¹² = 6.0 mm; θ = 1.5 × 2000³/(6 × 5.0 × 10¹¹) = 4.0 × 10⁻³ rad.

Answer. y = (−w x⁴/24 + w L³ x/6 − w L⁴/8)/(E I); δ_tip = 6.0 mm; θ_tip = 4.0 × 10⁻³ rad

Step-by-step procedure

  1. Draw the beam, choose the origin and state the sign convention (y up, sagging moment positive).
  2. Find the reactions and write M(x) for the whole beam, or for each segment.
  3. Write E I y″ = M(x) and integrate twice, adding C₁ and C₂ (and new constants for each extra segment).
  4. List the boundary conditions (y = 0 at supports, y′ = 0 at fixed ends, slope and deflection continuous between segments) and solve for the constants.
  5. Find the maximum deflection where y′ = 0 (or at the free end of a cantilever), and check units.
  6. Compare the deflection with the limit for the member's use, using the load case the code asks for.

Site notes

  • Floors with brittle finishes such as tiles, plaster or glass partitions need tighter deflection limits; cracks along partition heads and tiles lifting at midspan are typical signs of a floor that is too flexible.
  • Long-span steel and timber beams are often given a small upward camber at fabrication so that they end level under dead load; the camber should match the computed dead-load deflection, not the total.
  • Deflection grows with the fourth power of span for a distributed load: increasing a span from 5 m to 6 m increases the deflection by about 2.07 times for the same section, so long spans are usually governed by stiffness, not strength.
  • Concrete beams keep deflecting for years under sustained load because of creep and shrinkage; props removed too early increase the long-term sag.
Common mistakes
  • Mixing units, such as w in kN/m with L in mm and E in N/mm², giving deflections wrong by factors of 1000 or more; convert everything to N and mm, or to kN and m.
  • Using y′ = 0 at a simple support; a simple support allows rotation, and only y = 0 applies there.
  • Dropping the minus sign of a hogging moment in a cantilever, which puts the deflection upward.
  • Using the gross I of a cracked concrete beam in a deflection check, which underestimates the sag.
  • Checking only strength and assuming deflection will be fine on a long-span beam.
Quick check

Simply supported beam under a uniform load: δ = 5 w L⁴/(384 E I). Cantilever with a tip load: δ = P L³/(3 E I). Both scale with the cube or fourth power of span and only inversely with I, so doubling a rectangular beam's depth reduces deflection eight times. If a hand-computed floor deflection comes out in metres or as a fraction of a millimetre for a normal floor, recheck the units.

Summary

  • The elastic curve equation is E I y″ = M, from 1/R = M/(E I) and the small-slope curvature y″.
  • Sign convention in this chapter: y upward positive and sagging moment positive.
  • Two integrations give slope and deflection; the constants come from boundary conditions at the supports.
  • Standard results: 5 w L⁴/(384 E I) and P L³/(48 E I) for simply supported beams; P L³/(3 E I) and w L⁴/(8 E I) for cantilevers.
  • Codes set deflection limits in terms of span, such as IS 456:2000 cl. 23.2 for concrete and IS 800:2007 Table 6 for steel.

Practice questions

Tap a question to see the answer.

1A simply supported beam of span 4 m carries a central point load of 30 kN. E I = 1.0 × 10¹³ N·mm². Find the midspan deflection.

δ = P L³/(48 E I) = 30 × 10³ × 4000³/(48 × 1.0 × 10¹³) = 1.92 × 10¹⁵/4.8 × 10¹⁴ = 4.0 mm.

2Why is E I y″ = M called an approximation, and how large is the error for a slope of 0.01 rad?

It replaces the exact curvature y″/(1 + y′²)^(3/2) by y″. For y′ = 0.01, (1 + 0.0001)^(3/2) − 1 = 0.00015, an error of about 0.015%, negligible for building beams.

3State the boundary conditions for a propped cantilever fixed at A and simply supported at B.

At A: y = 0 and y′ = 0. At B: y = 0 and M = 0 (the beam is free to rotate).

4The depth of a rectangular timber beam is doubled while its width, span and load stay the same. What happens to its deflection?

I = b d³/12 increases 8 times, so the deflection falls to one-eighth.

5A simply supported beam of span 5 m carries 10 kN/m; E I = 2.0 × 10¹³ N·mm². Find the end slope and the midspan deflection.

θ = w L³/(24 E I) = 10 × 5000³/(24 × 2.0 × 10¹³) = 2.60 × 10⁻³ rad; δ = 5 × 10 × 5000⁴/(384 × 2.0 × 10¹³) = 4.07 mm.

6A simply supported beam carries a total load W either spread uniformly or as a single central point load. What is the ratio of the midspan deflections?

Uniform: 5 W L³/(384 E I); central: W L³/(48 E I). Ratio = (5/384)/(1/48) = 0.625, so spreading the load reduces the deflection to 62.5%.

References

Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.

  • B. J. Goodno, J. M. Gere, Mechanics of Materials, Cengage Learning, 9th edition, 2018.
  • R. C. Hibbeler, Mechanics of Materials, Pearson, 10th edition, 2016.
  • F. P. Beer, E. R. Johnston, J. T. DeWolf, D. F. Mazurek, Mechanics of Materials, McGraw Hill, 8th edition, 2020.
  • E. P. Popov, Engineering Mechanics of Solids, Prentice Hall, 2nd edition, 1998.
Suggest a correction

If something on this page is wrong, tell the editor. Your message is sent privately and is not published.

Sent privately to the Indiacon editor; not published.