Indiacon CivilSubscribe

Textbook › Strength of Materials › Chapter 4 › Lesson 4.3

4.3 Shear flow and shear centre

Strength of Materials Chapter 4: Shear stresses in beams Under review — not yet three-checked Author: Indiacon

Learning objectives

After this lesson you should be able to:

  • Define shear flow q = V Q/I as the horizontal shear force per unit length, and use it to space nails, bolts and welds in built-up beams.
  • Trace the shear flow around a thin-walled open section and find the resultant force in each part.
  • Locate the shear centre of a channel section, explain why a load that misses the shear centre twists the beam, and say where the shear centre lies for common sections.

Theory

Lesson 4.1 found the shear stress τ = V Q/(I b) on a horizontal plane. Multiplying by the width b of that plane gives the shear force carried per unit length of beam, q = V Q/I, called the shear flow. It is the quantity that matters for any joint running along a beam: the glue line between laminations, the nails between a timber flange and web, the welds between the flange and web of a plate girder, and the bolts that hold a cover plate on a steel beam. Each connector, spaced s apart, must carry q × s.

In a thin-walled section the shear flow runs along the wall like water in a pipe, which explains the name. In an I-section or channel under vertical shear, it starts at zero at the free tips of the flanges, grows linearly towards the web, turns down the web, where it follows a flat parabola, and leaves through the other flange. The flange flows are horizontal, so in a channel the top and bottom flanges carry equal and opposite horizontal forces, and the web carries nearly all of the vertical shear.

F (top flange)VF (bottom flange)shear centreePq = V Q/IF h = V ee = 3b²t_f/(6bt_f + ht_w)load through the shearcentre: bending, no twistIndiacon original, not to scale
Figure 4.3: Shear flow in a channel: flange flows give equal and opposite forces F whose couple shifts the resultant of the shear outside the web, to the shear centre at distance e. Indiacon original, not to scale.

Those two horizontal flange forces form a couple. In a channel, both point the same way round about the web, so the resultant of the shear flows is a vertical force that does not pass through the web. It acts at a point outside the section, on the side away from the flanges, called the shear centre. If the load passes through the shear centre, the beam bends without twisting. If the load passes anywhere else, for example through the web of a channel or through its centroid, the beam twists as well as bends.

Simple rules locate the shear centre in common shapes. It lies on any axis of symmetry, so for a doubly symmetric I-section or box it coincides with the centroid. For an angle or a tee it is at the point where the centrelines of the two legs, or of the flange and web, meet, because all the shear flows pass through that point. For a channel it lies on the axis of symmetry, outside the web by a distance e that depends on the flange width, depth and plate thicknesses. Open thin-walled sections are weak in torsion, so loading them away from the shear centre can cause large twists, which is why channel purlins and rails need care in orientation and bracing.

Derivation

  1. Shear flow: from lesson 4.1, the unbalanced force on the part beyond a cut over length dx is dF = dM Q/I, so the force per unit length is q = dF/dx = V Q/I (N/mm), independent of the width of the cut.
  2. Connector spacing: if each fastener can carry F and n fasteners share the joint at spacing s, then n F ≥ q s, so s ≤ n F/q.
  3. Channel under vertical shear V, centreline dimensions: web depth h between flange centrelines, flange width b from the web centreline, thicknesses t_f and t_w. In the top flange at distance s from the tip, Q = t_f s (h/2), so q(s) = V t_f s h/(2I), rising linearly to V t_f b h/(2I) at the web.
  4. Flange force: F = ∫₀ᵇ q ds = V t_f b² h/(4 I), acting horizontally; the two flanges carry equal and opposite forces h apart, a couple F h.
  5. For the resultant of all the shear flows to equal V acting at distance e from the web centreline, take moments about the web centreline at mid-height: V e = F h, so e = t_f b² h²/(4 I).
  6. With I ≈ t_w h³/12 + 2 b t_f (h/2)² (flange own second moments neglected), e = 3 b² t_f/(6 b t_f + h t_w); for equal thicknesses this is e = 3 b²/(6 b + h).
  7. Sections with an axis of symmetry have the shear centre on that axis; for an angle or tee it is at the junction of the centrelines, because every shear flow passes through that point and has zero moment about it.
Formulas, symbols and SI units
  • Shear flow: q = V Q/I (N/mm)
  • Connector spacing: s ≤ n F/q (mm), with n connectors per row each of capacity F
  • Channel flange shear flow at the web: q = V t_f b h/(2 I)
  • Channel flange force: F = V t_f b² h/(4 I)
  • Channel shear centre from the web centreline: e = t_f b² h²/(4 I) = 3 b² t_f/(6 b t_f + h t_w)
  • Torque from a load at distance a from the shear centre: T = V a
  • Units: V in N, Q in mm³, I in mm⁴, q in N/mm, b, h, e in mm
Assumptions and limits
  • Linear elastic material, slender beam, bending stresses from σ = M y/I.
  • Thin walls: shear flow is taken as uniform across the wall thickness and directed along the wall centreline; dimensions are measured to centrelines.
  • The second moments of the flanges about their own axes are neglected in the channel formula; the error is small for thin flanges.
  • For connector spacing, the connectors are assumed to share the shear flow equally and to be close enough for the members to act as one.
  • Limits: shear centre results are for open thin-walled sections in elastic bending; warping restraint, local buckling and plastic behaviour need a fuller torsion and stability analysis.

Codes and standards

Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.

  • Shear flow and the shear centre are mechanics and are not set by any design code; codes use them in the design of connectors and of members prone to twisting.
  • IS 800:2007 gives the design strengths of bolts and welds; the shear flow q = V Q/I is the demand that those strengths must meet along a built-up member. Codes also set maximum spacing limits for stitch fasteners, which can govern over the shear-flow spacing.
  • Side by side, not ranked: EN 1993-1-1, EN 1995-1-1 for timber and AISC 360 likewise take the longitudinal shear on connectors from elastic shear flow, and treat members loaded away from the shear centre with torsion and lateral-torsional buckling checks.

Worked examples

Example 1 (exam style: nailed timber T-beam)

Problem. A timber T-beam is made of a flange plank 150 × 50 mm nailed on top of a web plank 50 × 200 mm (overall depth 250 mm). It carries a shear force of 6 kN. Each nail can safely carry 0.8 kN. Find the shear flow at the joint and the nail spacing.

  1. Centroid from the bottom: ȳ = (7500 × 225 + 10 000 × 100)/17 500 = 153.57 mm.
  2. I = 150 × 50³/12 + 7500 × 71.43² + 50 × 200³/12 + 10 000 × 53.57² = 1.019 × 10⁸ mm⁴.
  3. Q of the flange about the neutral axis: 7500 × (225 − 153.57) = 5.357 × 10⁵ mm³.
  4. q = V Q/I = 6000 × 5.357 × 10⁵/1.019 × 10⁸ = 31.6 N/mm.
  5. One row of nails: s = 800/31.6 = 25.4 mm, too close for timber without splitting. Two rows: s = 2 × 800/31.6 = 50.7 mm, so nails in two staggered rows at 50 mm, or glue, or screws of higher capacity.

Answer. q = 31.6 N/mm; two rows of nails at 50 mm (one row would need 25 mm)

Example 2 (site style: bolting cover plates to a girder)

Problem. The welded I-section of lesson 4.2 (I = 3.279 × 10⁸ mm⁴, depth 400 mm) is strengthened with a 200 × 12 mm cover plate on each flange. At the support the shear force is 250 kN. Bolts are placed in pairs, one each side of the web, and each bolt can carry 45 kN in shear (problem data). Find the shear flow between plate and flange, the bolt spacing from shear flow, and the shear flow at each of the original flange-web welds without plates when V = 200 kN.

  1. New I = 3.279 × 10⁸ + 2 × (200 × 12³/12 + 2400 × 206²) = 5.317 × 10⁸ mm⁴.
  2. Q of one cover plate: 2400 × 206 = 4.944 × 10⁵ mm³.
  3. q = 250 × 10³ × 4.944 × 10⁵/5.317 × 10⁸ = 232.5 N/mm.
  4. Spacing of bolt pairs: s = 2 × 45 × 10³/232.5 = 387 mm; the code limit on stitch-bolt pitch may require closer spacing, and the smaller value is used.
  5. Original girder, flange-web joint at V = 200 kN: q = 200 × 10³ × 7.60 × 10⁵/3.279 × 10⁸ = 463.5 N/mm, shared by two fillet welds at 231.7 N/mm each.

Answer. q = 232.5 N/mm; bolt pairs at up to 387 mm from shear flow; flange-web welds 231.7 N/mm each

Example 3 (channel purlin: where must the load act?)

Problem. A channel has centreline dimensions h = 200 mm between flanges, flange width b = 75 mm from the web centreline, flange thickness 10 mm and web thickness 6 mm. Find the shear centre and the torque on the channel when a load of 5 kN is applied in the plane of the web.

  1. I ≈ t_w h³/12 + 2 b t_f (h/2)² = 6 × 200³/12 + 2 × 75 × 10 × 100² = 4.0 × 10⁶ + 15.0 × 10⁶ = 1.90 × 10⁷ mm⁴.
  2. e = t_f b² h²/(4 I) = 10 × 75² × 200²/(4 × 1.90 × 10⁷) = 29.6 mm from the web centreline, on the side away from the flanges.
  3. Check: e = 3 b² t_f/(6 b t_f + h t_w) = 3 × 5625 × 10/(4500 + 1200) = 29.6 mm.
  4. A load in the plane of the web misses the shear centre by 29.6 mm, so it applies a torque T = 5 × 29.6 = 148 N·m (0.148 kN·m) along with the bending.
  5. To avoid twisting, load the channel through a cleat or bracket that brings the load to the shear centre, use channels in back-to-back pairs, or brace them against rotation.

Answer. e = 29.6 mm outside the web; torque 148 N·m if loaded in the web plane

Step-by-step procedure

  1. Find V at the section and I of the complete section about the neutral axis.
  2. For a joint between parts, take Q of the part beyond the joint and compute q = V Q/I.
  3. Divide the connector capacity per row by q to get the spacing; check the code minimum and maximum spacing for the connector type.
  4. For a thin-walled open section, trace q along each part, from zero at free tips, and find the resultant force in each flange and web.
  5. Find the shear centre by taking moments of those resultants; check its position against the rules for symmetric sections, angles and tees.
  6. If the load does not pass through the shear centre, compute the torque and provide for it by restraint, pairing or a torsion check.

Site notes

  • Nail and bolt spacing in built-up timber and steel members is closest near the supports, where shear flow is largest; spacing can open up towards mid-span.
  • Fillet welds joining flanges to webs in plate girders are sized from shear flow; intermittent welds must be close enough to make the parts act together.
  • Channel purlins and side rails tend to roll under load because the load misses the shear centre; cleats, sag rods and correct orientation of the flanges control this.
  • Angles used as lintels or edge members twist if loaded through a leg far from the corner; seat the load near the heel or restrain the angle.
Common mistakes
  • Using τ = V Q/(I b) where the force per unit length, q = V Q/I, is wanted for connectors.
  • Taking Q of the whole section above the neutral axis instead of the part beyond the joint being checked.
  • Placing the shear centre of a channel at its centroid; it is on the other side of the web.
  • Forgetting that n connectors per row share the shear flow.
  • Ignoring code minimum and maximum spacing limits after computing spacing from shear flow.
Quick check

Connector spacing s = n F/q with q = V Q/I. The shear centre of a channel lies outside the web, on the side away from the flanges, at e = 3 b² t_f/(6 b t_f + h t_w); for equal thicknesses this is less than half the flange width. If a computed e falls inside the channel, a sign or dimension has been mixed up.

Summary

  • Shear flow q = V Q/I is the longitudinal shear force per unit length that joints along a beam must carry.
  • Connector spacing follows from s = n F/q and is closest near supports.
  • In thin-walled open sections the shear flow runs along the walls, from zero at free edges.
  • The shear centre is the point through which a load causes bending without twisting; it lies on any axis of symmetry.
  • For a channel it lies outside the web; for an angle or a tee at the junction of the leg centrelines.

Practice questions

Tap a question to see the answer.

1The welded I-section of lesson 4.2 (Q of one flange 7.60 × 10⁵ mm³, I = 3.279 × 10⁸ mm⁴) carries V = 200 kN. Find the shear flow at the flange-web junction and the force per mm on each of the two fillet welds.

q = 200 × 10³ × 7.60 × 10⁵/3.279 × 10⁸ = 463.5 N/mm; each weld carries 231.7 N/mm.

2Two timber planks 100 × 100 mm are nailed one above the other to form a 100 × 200 mm beam carrying V = 4 kN. Nails in two rows each carry 0.9 kN. Find the shear flow at the joint and the nail spacing.

I = 100 × 200³/12 = 6.667 × 10⁷ mm⁴, Q = 100 × 100 × 50 = 5 × 10⁵ mm³, q = 4000 × 5 × 10⁵/6.667 × 10⁷ = 30 N/mm. s = 2 × 900/30 = 60 mm.

3Where is the shear centre of a doubly symmetric I-section?

At the centroid, because the shear centre lies on both axes of symmetry.

4Where is the shear centre of an equal angle, and why?

At the intersection of the centrelines of the two legs (near the heel), because the shear flows in both legs act along those centrelines and so pass through that point.

5A channel has h = 150 mm, b = 60 mm, t_f = 8 mm and t_w = 5 mm (centreline dimensions). Find the distance of its shear centre from the web centreline.

e = 3 b² t_f/(6 b t_f + h t_w) = 3 × 3600 × 8/(2880 + 750) = 23.8 mm, outside the web.

6A channel purlin is loaded through its web. What happens, and give two ways to prevent it.

The load misses the shear centre, so the channel twists as well as bends and rolls over. Remedies: transfer the load through a cleat or bracket to the shear centre, use two channels back to back, add sag rods or bracing that restrain rotation, or use a section whose shear centre lies in the web plane, such as an I-section.

References

Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.

  • B. J. Goodno, J. M. Gere, Mechanics of Materials, Cengage Learning, 9th edition, 2018.
  • R. C. Hibbeler, Mechanics of Materials, Pearson, 10th edition, 2016.
  • F. P. Beer, E. R. Johnston, J. T. DeWolf, D. F. Mazurek, Mechanics of Materials, McGraw Hill, 8th edition, 2020.
  • E. P. Popov, Engineering Mechanics of Solids, Prentice Hall, 2nd edition, 1998.
Suggest a correction

If something on this page is wrong, tell the editor. Your message is sent privately and is not published.

Sent privately to the Indiacon editor; not published.