5.4 Conjugate beam method
After this lesson you should be able to:
- Explain the analogy between the load-shear-moment relations of a beam and the curvature-slope-deflection relations of its elastic curve, on which the conjugate beam method rests.
- Build the conjugate beam for a given real beam, transforming each support and internal hinge correctly, and load it with the M/(E I) diagram.
- Find slopes and deflections of real beams, including beams with varying E I, as the shear forces and bending moments of the conjugate beam.
Theory
Lessons 2.4 and 5.1 contain two chains of relations with exactly the same form. For loads on a beam, dV/dx = −w and dM/dx = V, so M″ = −w. For the elastic curve, θ = y′ and y″ = M/(E I). If an imaginary beam were loaded with the M/(E I) diagram, its shear and bending moment would therefore follow the same equations as the slope and deflection of the real beam. O. Mohr published this analogy in 1868, and it was later developed into what is now called the conjugate beam method.
The imaginary beam, the conjugate beam, has the same length as the real beam. It is loaded with the M/(E I) diagram of the real beam, so its total load is the area of that diagram. The shear force in the conjugate beam at any section equals the slope of the real beam there, and the bending moment in the conjugate beam equals the deflection of the real beam. Slopes and deflections are thus found with the same statics used for shear force and bending moment diagrams, which most students already handle confidently.
For the analogy to hold, the conjugate beam's supports must give the same boundary conditions in its shear and moment as the real beam has in slope and deflection. A pin or roller in the real beam has zero deflection but some slope, so its conjugate is also a pin or roller (zero moment, some shear). A fixed end has zero slope and zero deflection, so it becomes a free end in the conjugate beam. A free end has slope and deflection, so it becomes a fixed end. Inside a beam, a real hinge (deflection continuous, slope jumping) becomes a support, and a real intermediate support (deflection zero, slope continuous) becomes a hinge.
The conjugate beam of a statically determinate real beam is also statically determinate, so its reactions follow from equilibrium alone, and the deflection at a point is just a moment calculation. The method is especially handy for beams with varying E I, because the varying stiffness is already built into the load diagram, and it ties closely to the moment-area method of lesson 5.3: taking moments of the M/(E I) load is the same as applying moment-area theorem II. For a statically indeterminate real beam the conjugate beam comes out unstable, and it can only be in equilibrium under the true M/(E I) loading; that condition supplies the extra equations for the redundants.
Derivation
- Sign convention: y upward, sagging moment positive, as in lesson 5.1.
- Real beam: θ = dy/dx and dθ/dx = M/(E I).
- Conjugate beam with a downward distributed load w̄: dV̄/dx = −w̄ and dM̄/dx = V̄.
- Choose w̄ = −M/(E I), that is, apply the M/(E I) diagram as an upward load where M is sagging. Then dV̄/dx = M/(E I) and dM̄/dx = V̄, which are the same equations as for θ and y.
- If V̄ and M̄ satisfy the same boundary conditions as θ and y, then V̄ = θ and M̄ = y everywhere. In practice many engineers work with magnitudes and decide the direction of slope and deflection from the deflected shape.
- Support transformations follow from matching conditions: pin or roller (y = 0, θ ≠ 0) ↔ pin or roller (M̄ = 0, V̄ ≠ 0); fixed end (y = 0, θ = 0) ↔ free end (M̄ = 0, V̄ = 0); free end (y ≠ 0, θ ≠ 0) ↔ fixed end; internal hinge (θ jumps) ↔ internal support (V̄ jumps); internal support (y = 0, θ continuous) ↔ internal hinge (M̄ = 0, V̄ continuous).
- Check, simply supported beam with uniform load w: the conjugate beam is also simply supported and carries a parabolic load of peak w L²/(8 E I) and area w L³/(12 E I). Each conjugate reaction is half of that, w L³/(24 E I), the end slope. The conjugate moment at midspan is (w L³/(24 E I))(L/2) − (w L³/(24 E I))(3L/16) = 5 w L⁴/(384 E I), the midspan deflection.
Conjugate load: w̄ = M/(E I) (1/m), area of the diagram = total conjugate load (rad)Slope of real beam = shear force in conjugate beam: θ = V̄Deflection of real beam = bending moment in conjugate beam: y = M̄Pin or roller ↔ pin or roller; fixed end ↔ free end; internal hinge ↔ internal supportSimply supported, uniform load: conjugate reaction = w L³/(24 E I) = θ_endCantilever, tip load: conjugate fixed-end moment = P L³/(3 E I) = δ_tipUnits: M in kN·m, E I in kN·m², conjugate shear in rad, conjugate moment in m
- All assumptions of lesson 5.1 apply: linear elastic material, small slopes and deflections, shear deformation neglected.
- E I may vary along the beam; the M/(E I) load diagram takes the local value at each section.
- Supports and internal hinges must be transformed exactly as listed; a wrong transformation gives a conjugate beam with the wrong boundary conditions and wrong results.
- The conjugate beam is a calculation device; its reactions and internal forces have the units of slope (rad) and deflection (m), not of force.
- Limits: for statically indeterminate real beams the conjugate beam is a mechanism, so the method must be combined with the condition that it is in equilibrium; for such beams the slope-deflection or moment distribution methods are often quicker.
Codes and standards
Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.
- The conjugate beam method is mechanics; no code prescribes it, but its results feed the deflection checks that codes require.
- The limits explained in lesson 5.1 apply: IS 456:2000 cl. 23.2 for reinforced concrete members, using a stiffness that allows for cracking and long-term effects, and IS 800:2007 Table 6 for steel members.
- Side by side, not ranked: EN 1993-1-1, EN 1992-1-1, ACI 318 and AISC 360 practice all accept elastic deflections found by any consistent method, including hand methods of this kind for members with varying stiffness, and compare them with the limits of their own code family.
Worked examples
Problem. A steel canopy beam projects 2.5 m as a cantilever and carries an 8 kN load at its tip. E I = 1.0 × 10¹³ N·mm² (10 000 kN·m²). Find the tip slope and deflection by the conjugate beam method.
- Real beam: fixed at A, free at B. Conjugate beam: free at A, fixed at B.
- Load on the conjugate beam: a triangle of M/(E I), zero at B and P L/(E I) = 8 × 2.5/10 000 = 2.0 × 10⁻³ m⁻¹ at A.
- Total conjugate load = (1/2) × 2.5 × 2.0 × 10⁻³ = 2.5 × 10⁻³ rad, which is the conjugate shear at B, so θ_tip = 2.5 × 10⁻³ rad.
- Its centroid is L/3 = 0.833 m from A, so 1.667 m from B. Conjugate moment at B = 2.5 × 10⁻³ × 1.667 = 4.17 × 10⁻³ m.
- δ_tip = 4.17 mm, matching P L³/(3 E I) = 8 × 15.625/30 000 = 4.17 mm.
Answer. θ_tip = 2.5 × 10⁻³ rad; δ_tip = 4.17 mm
Problem. Repeat Example 1 of lesson 5.2 by the conjugate beam method: span 6 m, 40 kN at 2 m from A, E I = 24 000 kN·m². Find θ_A and the deflection under the load.
- The conjugate beam is simply supported. Peak M = P a b/L = 40 × 2 × 4/6 = 53.33 kN·m, so the peak conjugate load is 53.33/24 000 = 2.222 × 10⁻³ m⁻¹ at x = 2 m.
- Total conjugate load = (1/2) × 6 × 2.222 × 10⁻³ = 6.667 × 10⁻³ rad, acting at the centroid of the triangle, (L + a)/3 = 2.667 m from A.
- Conjugate reaction at A = 6.667 × 10⁻³ × (6 − 2.667)/6 = 3.70 × 10⁻³ rad = θ_A.
- Conjugate moment at x = 2 m: 3.704 × 10⁻³ × 2 − (1/2 × 2 × 2.222 × 10⁻³) × (2/3) = 7.407 × 10⁻³ − 1.481 × 10⁻³ = 5.93 × 10⁻³ m.
- Deflection under the load = 5.93 mm, the same as by Macaulay's method.
Answer. θ_A = 3.70 × 10⁻³ rad; δ under the load = 5.93 mm
Problem. A simply supported steel girder of span 8 m carries 100 kN at midspan. Cover plates over the central 4 m double its stiffness there: E I = 2E I₀ in the middle half and E I₀ = 8.0 × 10¹³ N·mm² (80 000 kN·m²) in the end quarters. Find the end slope and midspan deflection, and compare with an unplated girder.
- M = 50 x kN·m for 0 ≤ x ≤ 4 m. The conjugate load is 50 x/80 000 from 0 to 2 m and 50 x/160 000 from 2 to 4 m, symmetric about midspan.
- Conjugate load on each half: ∫₀² 50 x/80 000 dx + ∫₂⁴ 50 x/160 000 dx = 1.250 × 10⁻³ + 1.875 × 10⁻³ = 3.125 × 10⁻³ rad, which is each conjugate reaction, so θ_A = 3.125 × 10⁻³ rad.
- Conjugate moment at midspan = reaction × 4 − moment of the half load about midspan = moment of the half load about A: ∫₀² 50 x²/80 000 dx + ∫₂⁴ 50 x²/160 000 dx = 1.667 × 10⁻³ + 5.833 × 10⁻³ = 7.50 × 10⁻³ m.
- δ = 7.50 mm. Unplated (E I₀ throughout): P L³/(48 E I₀) = 100 × 512/(48 × 80 000) = 13.33 mm; plated over the full length: 6.67 mm.
- Plating only the central half gives most of the stiffness gain, because the moments there are largest.
Answer. θ_A = 3.13 × 10⁻³ rad; δ = 7.50 mm (13.33 mm unplated, 6.67 mm fully plated)
Step-by-step procedure
- Draw the bending moment diagram of the real beam and divide it by the local E I to get the conjugate load.
- Draw the conjugate beam: same span, supports and hinges transformed (pin stays pin, fixed becomes free, free becomes fixed, internal hinge becomes support, internal support becomes hinge).
- Apply the M/(E I) diagram as a load, splitting it into simple shapes with known areas and centroids.
- Find the conjugate reactions by equilibrium.
- The conjugate shear at a section gives the real slope, and the conjugate moment gives the real deflection.
- Check one result against a standard formula or another method, such as moment-area or Macaulay.
Site notes
- Cover-plated and haunched girders in older bridges and industrial buildings have stiffness that changes along the span; the conjugate beam handles them with a single moment calculation.
- Gerber or hinged cantilever beams, found in some older bridges and in purlin systems, have internal hinges where the slope jumps; in the conjugate beam these become supports, which makes the deflection pattern easy to follow.
- When strengthening an existing beam, comparing conjugate beam deflections for different plate lengths shows where added material buys the most stiffness.
- The method is a quick hand check on software results for non-prismatic members, where input errors in section properties are common.
- Leaving a fixed end fixed in the conjugate beam instead of making it free (and the free end fixed).
- Loading the conjugate beam with the bending moment diagram instead of M/(E I) when E I varies.
- Treating conjugate reactions as forces in kN instead of slopes in radians.
- Taking the centroid of the M/(E I) load from the wrong end when computing conjugate moments.
- Applying the method to an indeterminate beam without noticing that the conjugate beam is unstable.
Real slope = conjugate shear; real deflection = conjugate moment, with the conjugate beam loaded by M/(E I). Pins stay pins, fixed ends and free ends swap, and internal hinges and supports swap. If the conjugate beam you have drawn needs more than equilibrium to solve while the real beam is determinate, a support has been transformed wrongly.
Summary
- The conjugate beam rests on the identical form of the load-shear-moment and curvature-slope-deflection relations.
- It has the same span as the real beam and is loaded with the M/(E I) diagram.
- Conjugate shear gives the real slope and conjugate moment the real deflection.
- Supports transform: pin to pin, fixed to free, free to fixed, internal hinge to support and internal support to hinge.
- It is quick for beams with varying E I and for hinged beams, and it agrees with Macaulay and moment-area results.
Practice questions
Tap a question to see the answer.
1What does a fixed end of a real beam become in the conjugate beam, and why?
A free end. The real fixed end has zero slope and zero deflection, so the conjugate beam must have zero shear and zero moment there, which is what a free end provides.
2Draw in words the conjugate beam of a cantilever fixed at A and free at B.
A cantilever of the same length, free at A and fixed at B, loaded with the M/(E I) diagram of the real beam.
3What do an internal hinge and an intermediate support of a real beam become in the conjugate beam?
An internal hinge becomes an intermediate support (the slope may jump, so the conjugate shear may jump). An intermediate support becomes an internal hinge (zero deflection, continuous slope, so zero conjugate moment and continuous conjugate shear).
4A simply supported beam of span 6 m carries 10 kN/m; E I = 3.0 × 10¹³ N·mm². Use the conjugate beam to find the end slope and the midspan deflection.
Conjugate load area = w L³/(12 E I); each reaction = w L³/(24 E I) = 10 × 6000³/(24 × 3.0 × 10¹³) = 3.0 × 10⁻³ rad. Conjugate moment at midspan = 5 w L⁴/(384 E I) = 5 × 10 × 6000⁴/(384 × 3.0 × 10¹³) = 5.63 mm.
5A cantilever 2 m long carries 3 kN/m; E I = 4000 kN·m². Find the tip slope and deflection by the conjugate beam method.
The conjugate beam is fixed at the tip and loaded by a parabolic spandrel of area w L³/(6 E I) = 3 × 8/24 000 = 1.0 × 10⁻³ rad (the tip slope), with centroid 3L/4 = 1.5 m from the tip. Tip deflection = 1.0 × 10⁻³ × 1.5 = 1.5 × 10⁻³ m = 1.5 mm.
6What happens to the conjugate beam of a beam fixed at both ends, and how is this used?
Both fixed ends become free ends, so the conjugate beam has no supports at all. It can be in equilibrium only if the M/(E I) load has zero total and zero moment; these two conditions give the two unknown fixed-end moments of the real beam.
References
Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.
- B. J. Goodno, J. M. Gere, Mechanics of Materials, Cengage Learning, 9th edition, 2018.
- R. C. Hibbeler, Mechanics of Materials, Pearson, 10th edition, 2016.
- F. P. Beer, E. R. Johnston, J. T. DeWolf, D. F. Mazurek, Mechanics of Materials, McGraw Hill, 8th edition, 2020.
- E. P. Popov, Engineering Mechanics of Solids, Prentice Hall, 2nd edition, 1998.