Indiacon CivilSubscribe

Textbook › Strength of Materials › Chapter 4 › Lesson 4.1

4.1 Shear stress formula

Strength of Materials Chapter 4: Shear stresses in beams Under review — not yet three-checked Author: Indiacon

Learning objectives

After this lesson you should be able to:

  • Explain why a beam that carries a varying bending moment must also carry shear stresses, both on its cross-sections and on horizontal planes along its length.
  • Derive the shear stress formula τ = V Q/(I b) from the equilibrium of a slice of beam, and say what Q, I and b each stand for.
  • Calculate shear stresses at any level of rectangular, circular and T-sections, and compare the peak with the average V/A.

Theory

Chapter 3 dealt with the normal stresses that bending produces. Wherever the bending moment changes along a beam, there is also a shear force, because dM/dx = V (lesson 2.4). That shear force has to be carried by stresses acting on the cross-section, parallel to it. A simple experiment shows that these stresses also act along the length of the beam. Stack two planks loosely and load them as a beam: they slide over each other at the interface and the ends no longer line up. Glue the same planks together and the sliding stops, and the beam becomes much stiffer and stronger. The glue is carrying horizontal shear stress.

Shear stress on a horizontal plane and shear stress on the vertical cross-section are two sides of the same coin. Any small element in equilibrium must have equal shear stresses on perpendicular faces (complementary shear stress), so the vertical shear stress at a point of the cross-section equals the horizontal shear stress on the plane through that point. It is easier to work out the horizontal one, because it is set by the imbalance of bending forces between two nearby cross-sections.

NAM Q/I(M+dM) Q/Iτ b dxdxarea A′1.5 V/(b d)τ = 0 at topτ = 0 at bottomτ = V Q/(I b)Indiacon original, not to scale
Figure 4.1: Shear stress formula: the unbalanced bending force on a slice above any level is carried by shear on the horizontal cut, giving τ = V Q/(I b); in a rectangle it is parabolic with a peak of 1.5 times the average. Indiacon original, not to scale.

Take the part of the beam above some level and cut out a short length dx. The bending stresses on its two ends differ, because the moment changes by dM over the length. The difference in the push on the two ends must be balanced by the shear on the horizontal cut at the bottom of the piece. Working this through gives τ = V Q/(I b), where V is the shear force at the section, I is the second moment of area of the whole section about the neutral axis, b is the width of the section at the level considered, and Q is the first moment about the neutral axis of the area beyond that level.

Q is zero at the top and bottom faces and grows towards the neutral axis, so the shear stress is zero at the extreme fibres, where the bending stress is largest, and usually largest at the neutral axis, where the bending stress is zero. The width b matters too: where the section narrows, as at the junction of a flange and a thin web, the shear stress jumps. For a rectangle the peak is 1.5 times the average V/A, and for a solid circle 4/3 times. Lesson 4.2 works through the common shapes.

Derivation

  1. Consider a beam element between sections x and x + dx, where the moments are M and M + dM. Cut it horizontally at distance y₁ above the neutral axis and keep the part above the cut, of area A′.
  2. The bending stress on the left face is σ = M y/I, so the total normal force on the left end of the part is F = ∫ M y/I dA = (M/I) ∫ y dA = M Q/I, with Q = ∫ y dA taken over A′ (equal to A′ ȳ′, where ȳ′ is the distance of the centroid of A′ from the neutral axis).
  3. On the right end the force is (M + dM) Q/I, so the unbalanced force is dF = dM Q/I.
  4. This is balanced by the shear stress τ acting over the horizontal cut of width b and length dx: τ b dx = dM Q/I.
  5. Divide by dx and use dM/dx = V: τ = V Q/(I b).
  6. By complementary shear, the same τ acts vertically on the cross-section at level y₁.
  7. Rectangle b × d: Q(y) = b (d/2 − y)(d/2 + y)/2 = (b/2)(d²/4 − y²), so τ(y) = V (d²/4 − y²)/(2 I) = (6 V/(b d³))(d²/4 − y²), a parabola with τ_max = 1.5 V/(b d) at y = 0.
Formulas, symbols and SI units
  • Shear stress at a level: τ = V Q/(I b) (N/mm²)
  • First moment of area beyond the level: Q = A′ ȳ′ (mm³)
  • Rectangle: τ(y) = (6 V/(b d³))(d²/4 − y²); τ_max = 1.5 V/(b d) = 1.5 τ_avg
  • Solid circle: τ_max = (4/3) V/A at the neutral axis
  • Average shear stress: τ_avg = V/A
  • Relation used: dM/dx = V
  • Units: V in N, Q in mm³, I in mm⁴, b in mm, τ in N/mm²
Assumptions and limits
  • Bending stresses follow σ = M y/I (lesson 3.1), so the beam is linear elastic and slender.
  • The shear stress is uniform across the width b at a given level; this is close for narrow sections, less so for wide flanges or very wide rectangles.
  • The shear stress acts parallel to the shear force; near free edges of non-rectangular shapes, such as a circle, it actually follows the boundary, and the formula gives its vertical component.
  • The section is prismatic over the length dx, and the load passes through the shear centre (lesson 4.3), so there is no torsion.
  • Limits: the formula is not accurate for very short, deep members, close to point loads and supports, at sudden changes of section, in cracked reinforced concrete, or after yielding.

Codes and standards

Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.

  • The shear stress formula is mechanics; codes use it for elastic checks and simplify it for strength design.
  • IS 456:2000 cl. 40.1 defines a nominal shear stress τ_v = V_u/(b d) for reinforced concrete beams, using the breadth and effective depth; it is a design parameter, not the true elastic peak, and is compared with the design shear strength of concrete given in that code.
  • IS 800:2007 cl. 8.4.1 takes the plastic shear resistance of a steel web as V_p = A_v f_yw/√3, the yield shear stress spread uniformly over a shear area A_v (lesson 4.2).
  • Side by side, not ranked: ACI 318 also works with an average shear stress over the web width and effective depth for concrete beams, and EN 1993-1-1 and AISC 360 use a shear area of the web for steel beams, with partial factors or resistance factors applied in each.

Worked examples

Example 1 (exam style: rectangular timber beam)

Problem. The timber beam of lesson 3.1 (150 mm × 300 mm, span 4 m, 10 kN/m) is checked for shear. Find the maximum shear stress and the shear stress at a level 50 mm below the top face, near a support.

  1. Maximum shear force at the support: V = wL/2 = 10 × 4/2 = 20 kN.
  2. τ_max = 1.5 V/(b d) = 1.5 × 20 × 10³/(150 × 300) = 0.667 N/mm², at the neutral axis.
  3. At 50 mm below the top, y = 100 mm from the neutral axis. Area above: 150 × 50 mm, centroid 125 mm from the neutral axis, so Q = 150 × 50 × 125 = 9.375 × 10⁵ mm³.
  4. I = 3.375 × 10⁸ mm⁴; τ = 20 × 10³ × 9.375 × 10⁵/(3.375 × 10⁸ × 150) = 0.370 N/mm².
  5. Check with the parabola: τ = V (d²/4 − y²)/(2 I) = 20 × 10³ × (22 500 − 10 000)/(6.75 × 10⁸) = 0.370 N/mm².

Answer. τ_max = 0.667 N/mm² at the neutral axis; 0.370 N/mm² at 50 mm below the top

Example 2 (T-section: the jump at the flange)

Problem. The T-section of lesson 3.1 (flange 150 × 20 mm, web 20 × 180 mm, overall depth 200 mm; neutral axis 135.45 mm above the bottom, I = 2.618 × 10⁷ mm⁴) carries a shear force of 30 kN. Find the shear stress at the neutral axis and just below and just above the flange-web junction.

  1. At the neutral axis, take the web area below it: Q = 20 × 135.45 × 135.45/2 = 1.835 × 10⁵ mm³ (the area above gives the same value, as a check).
  2. τ_NA = 30 × 10³ × 1.835 × 10⁵/(2.618 × 10⁷ × 20) = 10.51 N/mm².
  3. At the junction, Q is that of the flange alone: Q_f = 150 × 20 × (190 − 135.45) = 1.636 × 10⁵ mm³.
  4. Just below the junction (in the web, b = 20 mm): τ = 30 × 10³ × 1.636 × 10⁵/(2.618 × 10⁷ × 20) = 9.37 N/mm².
  5. Just above it (in the flange, b = 150 mm): τ = 9.37 × 20/150 = 1.25 N/mm². The same Q is spread over a width 7.5 times larger, so the stress drops sharply.

Answer. τ_NA = 10.51 N/mm²; at the junction 9.37 N/mm² in the web and 1.25 N/mm² in the flange

Example 3 (site style: a steel pin used as a short beam)

Problem. A solid steel pin of 40 mm diameter in a hanger bracket transfers a shear force of 30 kN across one plane. Find the average shear stress and the peak shear stress given by the shear formula.

  1. A = π × 40²/4 = 1257 mm²; τ_avg = 30 × 10³/1257 = 23.9 N/mm².
  2. For a solid circle Q at the neutral axis = 2r³/3, I = π r⁴/4 and b = 2r, so τ_max = (4/3) V/A.
  3. τ_max = (4/3) × 23.9 = 31.8 N/mm².
  4. Connection design normally uses average shear on bolts and pins with a strength that already allows for this non-uniform spread; the elastic peak is what a strain gauge would see.

Answer. τ_avg = 23.9 N/mm²; τ_max = 31.8 N/mm²

Step-by-step procedure

  1. Find the shear force V at the section from the shear force diagram; the largest is usually near a support or a heavy point load.
  2. Locate the neutral axis and find I of the whole section about it.
  3. For each level of interest, take the area beyond that level (above or below, whichever is simpler) and find Q = A′ ȳ′.
  4. Use the width b of the section at that level, not the width of the whole flange.
  5. Compute τ = V Q/(I b); check the neutral axis and every level where the width changes.
  6. Compare with the permissible or design shear stress, or follow the code shear check for the material.

Site notes

  • Shear is largest near supports, so this is where timber beams split along the grain and where notches at the bottom of a timber joist at its bearing are most harmful.
  • Built-up timber or laminated beams depend on glue or connectors to carry the horizontal shear at each interface; poor glue lines near supports show up as delamination.
  • In reinforced concrete, diagonal cracks near supports are caused by the combination of shear and bending stresses; stirrups are placed most closely there for that reason.
  • Holes through the web of a steel or concrete beam for services should stay away from supports and from the neutral axis zone near them, where shear stress is highest, unless they are designed for.
Common mistakes
  • Using the total area of the section for Q instead of the area beyond the level considered.
  • Using the flange width instead of the web width just below the junction.
  • Taking I about the base instead of about the neutral axis.
  • Assuming the shear stress is uniform and equal to V/A, which understates the peak by 50% for a rectangle.
  • Forgetting that Q is zero at the extreme fibres, so the shear stress there is zero.
Quick check

For a rectangle the peak shear stress is 1.5 V/(b d); for a solid circle 4/3 V/A. A hand result for a rectangle that is not 1.5 times V/A, or a shear stress that is not zero at the top and bottom faces, points to a wrong Q or b. Valid for linear elastic, slender beams.

Summary

  • Varying bending moment means shear force, and shear force means shear stresses on cross-sections and on horizontal planes.
  • Complementary shear makes the vertical and horizontal shear stresses equal at a point.
  • τ = V Q/(I b), with Q the first moment of the area beyond the level and b the width at that level.
  • Shear stress is zero at the extreme fibres and usually greatest at the neutral axis.
  • The peak is 1.5 times the average for a rectangle and 4/3 times for a solid circle.

Practice questions

Tap a question to see the answer.

1A rectangular beam 230 mm wide and 450 mm deep carries a shear force of 60 kN. Find the maximum shear stress.

τ_max = 1.5 V/(b d) = 1.5 × 60 × 10³/(230 × 450) = 0.870 N/mm².

2For a rectangular section, what fraction of the peak shear stress acts at a quarter of the depth from the top?

y = d/4 from the neutral axis: τ/τ_max = (d²/4 − d²/16)/(d²/4) = 0.75.

3A solid circular bar of 100 mm diameter carries a shear force of 50 kN. Find the maximum shear stress.

A = 7854 mm²; τ_max = (4/3) × 50 × 10³/7854 = 8.49 N/mm².

4What does Q represent in τ = V Q/(I b), and where is it largest?

Q is the first moment, about the neutral axis, of the part of the section beyond the level considered. It is largest at the neutral axis, where it equals the first moment of half the section on either side.

5In a T-section beam with a uniform web, at what level is the shear stress largest, and why?

At the neutral axis, provided it lies in the web. Q is largest there and the width b is the constant web width, so V Q/(I b) peaks at that level.

6A timber beam 100 mm wide and 200 mm deep has a permissible shear stress of 0.8 N/mm². What is the largest shear force it can carry?

V = τ b d/1.5 = 0.8 × 100 × 200/1.5 = 10 667 N = 10.67 kN.

References

Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.

  • B. J. Goodno, J. M. Gere, Mechanics of Materials, Cengage Learning, 9th edition, 2018.
  • R. C. Hibbeler, Mechanics of Materials, Pearson, 10th edition, 2016.
  • F. P. Beer, E. R. Johnston, J. T. DeWolf, D. F. Mazurek, Mechanics of Materials, McGraw Hill, 8th edition, 2020.
  • E. P. Popov, Engineering Mechanics of Solids, Prentice Hall, 2nd edition, 1998.
Suggest a correction

If something on this page is wrong, tell the editor. Your message is sent privately and is not published.

Sent privately to the Indiacon editor; not published.