Indiacon CivilSubscribe

Textbook › Strength of Materials › Chapter 4 › Lesson 4.2

4.2 Shear stress distribution in common sections

Strength of Materials Chapter 4: Shear stresses in beams Under review — not yet three-checked Author: Indiacon

Learning objectives

After this lesson you should be able to:

  • Derive the shear stress distribution across rectangular, circular, triangular, diamond, thin tubular and I-sections from τ = V Q/(I b).
  • State the ratio of peak to average shear stress for each common shape and where the peak occurs.
  • Show by calculation that the web of an I-section carries almost all the shear force, and use this in the shear check of a steel beam to IS 800:2007.

Theory

The shear formula of lesson 4.1 gives the stress at one level. Plotting it over the depth shows how different shapes share out the shear force, and the pattern always follows the same logic: τ is proportional to Q/b. Q rises from zero at the outer fibre to a maximum at the neutral axis, while b depends on the shape. Where b is constant, as in a rectangle, the curve is a smooth parabola. Where b changes, the curve changes with it.

For a solid circle the width shrinks towards the top and bottom, but Q still peaks at the neutral axis, so the peak is there and equals 4/3 times the average. For a thin-walled tube the width at the neutral axis is just twice the wall thickness, and the peak is about twice the average. A triangle and a square standing on its corner (a diamond) are the textbook surprises: their width is small near the neutral axis compared with lower levels, and the peak shear stress lies off the neutral axis, at mid-height for the triangle and at one-eighth of the diagonal from the neutral axis for the diamond.

rectangle 1.5×I-section: web carries Vtriangle: peak at h/2NA (rect, I)Indiacon original, not to scale
Figure 4.2: Shear stress follows Q/b: a parabola in a rectangle, a jump at the flange-web junction and a nearly uniform web stress in an I-section, and a peak at mid-height in a triangle. Indiacon original, not to scale.

The I-section shows the most practical result. Within the flanges, the width is large and the shear stress is small. At the flange-web junction the width suddenly falls to the web thickness and the stress jumps up by the ratio of the two widths. Within the web the stress follows a flat parabola, only a little larger at the neutral axis than at the junction. Integrating the web stresses shows that the web carries well over 90% of the shear force, while the flanges carry most of the bending moment. That division of labour is why steel codes check shear on the web alone.

The elastic distribution is what a beam has in service. At the strength limit, a ductile steel web yields in shear and the stress spreads out almost uniformly over the web. Codes therefore take the shear strength as the shear yield stress times a shear area, rather than limiting the elastic peak. For a material that obeys the von Mises yield condition, the shear yield stress is the tensile yield stress divided by √3.

Derivation

  1. Rectangle b × d: τ(y) = (V/(2I))(d²/4 − y²), giving τ_max = 1.5 V/A at y = 0 (lesson 4.1).
  2. Solid circle of radius r: at height y the width is b = 2√(r² − y²) and Q = (2/3)(r² − y²)^(3/2), so τ = V (r² − y²)/(3I) with I = π r⁴/4; at y = 0, τ_max = 4V/(3π r²) = (4/3) V/A.
  3. Thin circular tube of mean radius r and wall t: I ≈ π r³ t, Q at the neutral axis ≈ 2 r² t, b = 2t, so τ_max ≈ V × 2 r² t/(π r³ t × 2t) = V/(π r t) = 2 V/A.
  4. Triangle of base B and height h, apex up: at depth z below the apex the width is B z/h. With I = B h³/36 and the neutral axis at z = 2h/3, the area above the level has Q = B z² (h − z)/(3h), so τ(z) = 12 V z (h − z)/(B h³). The peak is at z = h/2, τ_max = 1.5 V/A, and at the neutral axis (z = 2h/3) τ = (4/3) V/A.
  5. Square of diagonal d with the diagonal vertical (a diamond): b varies linearly from zero at the top corner; τ peaks at d/8 above and below the neutral axis, τ_max = (9/8) V/A, and at the neutral axis τ = V/A.
  6. I-section: in the flange at the junction τ = V Q_f/(I B); just inside the web τ = V Q_f/(I t_w), larger by B/t_w; at the neutral axis τ = V (Q_f + t_w h_w²/8)/(I t_w), where h_w is the clear web depth.
  7. Web share of the shear: V_web = ∫ τ t_w dy over the web = (V/I)[Q_f h_w + t_w h_w³/12].
Formulas, symbols and SI units
  • Rectangle: τ_max = 1.5 V/A at the neutral axis
  • Solid circle: τ_max = (4/3) V/A at the neutral axis
  • Thin tube: τ_max ≈ 2 V/A at the neutral axis
  • Triangle: τ_max = 1.5 V/A at mid-height; at the neutral axis (4/3) V/A
  • Diamond (square on its corner): τ_max = (9/8) V/A at d/8 from the neutral axis
  • I-section web: τ_NA = V (Q_f + t_w h_w²/8)/(I t_w); jump at the junction by B/t_w
  • Steel web plastic shear resistance (IS 800:2007 cl. 8.4.1): V_p = A_v f_yw/√3; design V_d = V_p/γ_m0, γ_m0 = 1.10
  • Shear area (IS 800:2007 cl. 8.4.1.1, major-axis bending of I and channel sections): A_v = h t_w for hot-rolled sections and d t_w for welded sections
Assumptions and limits
  • Linear elastic material and slender beam, as in lesson 4.1.
  • The shear stress is uniform across the width at each level; in wide flanges the real stresses are mostly horizontal and the vertical values from the formula are only an approximation.
  • Thin-walled results use the centreline of the wall and ignore terms in t².
  • Loads pass through the shear centre, so there is no twisting.
  • Limits: the elastic distribution does not hold after yielding, in cracked concrete, near supports and point loads, or in slender webs that buckle in shear.

Codes and standards

Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.

  • IS 800:2007 cl. 8.4.1 gives the nominal plastic shear resistance V_p = A_v f_yw/√3 and the design shear strength V_d = V_p/γ_m0, with γ_m0 = 1.10. Cl. 8.4.1.1 sets the shear area for major-axis bending of I and channel sections as h t_w for hot-rolled and d t_w for welded sections (h overall depth, d clear web depth). The code also has a shear buckling check for slender webs.
  • IS 800:2007 cl. 8.2.1.2 treats shear as low when the design shear force does not exceed 0.6 V_d; the bending strength is then not reduced (lesson 3.2).
  • IS 456:2000 cl. 40.1 uses the nominal shear stress τ_v = V_u/(b d) for concrete beams, with the web breadth for flanged beams.
  • Side by side, not ranked: EN 1993-1-1 and AISC 360 also base the shear resistance of steel webs on a shear area and a shear yield stress, each with its own definition of the area and its own partial or resistance factor.

Worked examples

Example 1 (welded I-section: the web carries the shear)

Problem. The welded I-section of lessons 3.2 and 3.4 (flanges 200 × 20 mm, web 360 × 10 mm, I = 3.279 × 10⁸ mm⁴) carries a shear force of 200 kN. Find the shear stress in the flange and in the web at the junction, at the neutral axis, and the share of the shear force carried by the web.

  1. Q of one flange about the neutral axis: Q_f = 200 × 20 × 190 = 7.60 × 10⁵ mm³.
  2. At the junction, in the flange (b = 200 mm): τ = 200 × 10³ × 7.60 × 10⁵/(3.279 × 10⁸ × 200) = 2.32 N/mm². In the web (b = 10 mm): τ = 46.35 N/mm², 20 times larger.
  3. At the neutral axis: Q = 7.60 × 10⁵ + 10 × 180 × 90 = 9.22 × 10⁵ mm³; τ = 200 × 10³ × 9.22 × 10⁵/(3.279 × 10⁸ × 10) = 56.23 N/mm².
  4. Web share: V_web = (V/I)[Q_f h_w + t_w h_w³/12] = (200 × 10³/3.279 × 10⁸)[7.60 × 10⁵ × 360 + 10 × 360³/12] = 190.6 kN, that is 95.3% of the shear.
  5. Average over the clear web, V/(h_w t_w) = 200 × 10³/3600 = 55.6 N/mm², within about 1% of the peak, which is why codes use a web shear area.

Answer. Flange 2.32 N/mm², web at junction 46.35 N/mm², neutral axis 56.23 N/mm²; the web carries 95.3% of the shear

Example 2 (design check to IS 800:2007)

Problem. Check the same welded section, steel with f_y = 250 N/mm², for a factored shear force of 200 kN, and say whether the shear is low.

  1. Welded I-section, major-axis bending: A_v = d t_w = 360 × 10 = 3600 mm² (cl. 8.4.1.1).
  2. V_p = A_v f_yw/√3 = 3600 × 250/1.732 = 519.6 kN (cl. 8.4.1).
  3. V_d = V_p/γ_m0 = 519.6/1.10 = 472.4 kN, greater than 200 kN, so the web is adequate in shear (the web is stocky, d/t_w = 36).
  4. 0.6 V_d = 283.4 kN > 200 kN, so the shear is low and the bending strength need not be reduced (cl. 8.2.1.2).

Answer. V_d = 472.4 kN ≥ 200 kN; low shear (200 < 283.4 kN)

Example 3 (site style: a steel tube used as a short beam)

Problem. A circular hollow section 168.3 mm outside diameter and 4.5 mm wall (problem data) is used as a short spreader beam and carries a shear force of 40 kN. Find the peak shear stress exactly and with the thin-tube rule.

  1. R = 84.15 mm, r = 79.65 mm. A = π(R² − r²) = 2316 mm². I = π(R⁴ − r⁴)/4 = 7.772 × 10⁶ mm⁴.
  2. Q of the half-ring at the neutral axis: (2/3)(R³ − r³) = 6.038 × 10⁴ mm³; b = 2t = 9 mm.
  3. τ_max = 40 × 10³ × 6.038 × 10⁴/(7.772 × 10⁶ × 9) = 34.53 N/mm².
  4. Thin-tube rule: τ_max ≈ 2 V/A = 2 × 40 × 10³/2316 = 34.55 N/mm², practically the same; the average V/A is 17.27 N/mm².

Answer. τ_max = 34.53 N/mm² (thin-tube rule 34.55 N/mm²), twice the average 17.27 N/mm²

Step-by-step procedure

  1. Sketch the section and mark every level where the width changes, plus the neutral axis.
  2. Find I about the neutral axis and Q at each marked level, using the area beyond the level.
  3. At a width change, compute τ with the width on each side of the line to show the jump.
  4. Plot τ over the depth and read off the peak; for shapes like triangles and diamonds check off the neutral axis as well.
  5. For steel beams, check the factored shear against the design shear strength of the web from the code; for concrete beams, follow the nominal shear stress route of the concrete code.

Site notes

  • Web openings for ducts and pipes in steel beams remove the part of the section that carries the shear; they need checking and often stiffening, especially near supports.
  • Coping or notching the top flange and part of the web at a beam end for a connection cuts the shear area exactly where the shear is largest; the remaining web must be checked.
  • Plate girders with deep, thin webs are fitted with vertical stiffeners near supports to stop the web from buckling in shear.
  • For hollow sections used as short beams or posts, shear is often larger than expected compared with a solid bar of the same area, because the peak is twice the average.
Common mistakes
  • Assuming the peak is always at the neutral axis; for triangles and diamonds it is not.
  • Using the flange width at the junction in the web, which hides the jump in stress.
  • Counting the flanges in the shear area of a steel beam bent about its major axis.
  • Mixing up the hot-rolled and welded shear areas: overall depth for hot-rolled, clear web depth for welded sections.
  • Using the elastic peak shear stress in place of the code shear strength check, or the other way round.
Quick check

Peak-to-average ratios: rectangle 1.5, solid circle 4/3, thin tube 2, triangle 1.5, diamond 9/8. For an I-section the web carries well over 90% of the shear and the web average is close to the peak. A web result below the flange result means the widths have been swapped.

Summary

  • τ follows Q/b: smooth where the width is constant, with jumps where the width changes.
  • Peak-to-average ratios: rectangle 1.5, circle 4/3, thin tube 2, triangle 1.5 at mid-height, diamond 9/8 at d/8 from the neutral axis.
  • In an I-section the flanges carry the bending and the web carries the shear.
  • Steel codes check shear as the shear yield stress over a web shear area: IS 800:2007 uses V_p = A_v f_yw/√3.
  • Concrete codes use a nominal shear stress V/(b d) compared with tabulated concrete shear strength.

Practice questions

Tap a question to see the answer.

1A square timber post of side 141.4 mm (diagonal 200 mm) is loaded as a beam with its diagonal vertical and carries a shear force of 20 kN. Find the average and the peak shear stress and where the peak occurs.

A = 141.4² = 20 000 mm²; τ_avg = 1.0 N/mm². The peak is (9/8) × 1.0 = 1.125 N/mm² at d/8 = 25 mm above and below the neutral axis.

2A triangular section with base 300 mm and height 300 mm carries a shear force of 45 kN. Find the peak shear stress and the shear stress at the neutral axis.

A = 45 000 mm², τ_avg = 1.0 N/mm². Peak 1.5 N/mm² at mid-height; at the neutral axis (two-thirds of the height from the apex) 1.333 N/mm².

3In an I-section with flange width 200 mm and web thickness 10 mm, by what factor does the shear stress jump at the flange-web junction?

τ ∝ 1/b at the same Q, so it jumps by 200/10 = 20 times.

4Why do steel codes check only the web of an I-beam for shear?

The web carries well over 90% of the shear force (95% in Example 1), and its stress is nearly uniform, so a web shear area gives an accurate and simple strength check.

5A concrete beam 300 mm wide with an effective depth of 500 mm carries a factored shear force of 180 kN. Find the nominal shear stress used by IS 456:2000.

τ_v = V_u/(b d) = 180 × 10³/(300 × 500) = 1.2 N/mm² (cl. 40.1).

6A hot-rolled I-section has overall depth 300 mm and web thickness 7.5 mm (problem data), with f_y = 250 N/mm². Find its design shear strength to IS 800:2007.

A_v = h t_w = 300 × 7.5 = 2250 mm² (cl. 8.4.1.1). V_d = A_v f_yw/(√3 γ_m0) = 2250 × 250/(1.732 × 1.10) = 295.2 kN.

References

Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.

  • B. J. Goodno, J. M. Gere, Mechanics of Materials, Cengage Learning, 9th edition, 2018.
  • R. C. Hibbeler, Mechanics of Materials, Pearson, 10th edition, 2016.
  • F. P. Beer, E. R. Johnston, J. T. DeWolf, D. F. Mazurek, Mechanics of Materials, McGraw Hill, 8th edition, 2020.
  • E. P. Popov, Engineering Mechanics of Solids, Prentice Hall, 2nd edition, 1998.
Suggest a correction

If something on this page is wrong, tell the editor. Your message is sent privately and is not published.

Sent privately to the Indiacon editor; not published.