2.3 SFD and BMD of simply supported and overhanging beams
After this lesson you should be able to:
- Find the reactions and then write the shear force and bending moment equations, segment by segment, for simply supported beams under point loads, uniform loads, triangular loads and applied couples.
- Locate the section of zero shear and use it to find the maximum bending moment, including the standard results PL/4, Pab/L, wL²/8 and w₀L²/(9√3).
- Draw the SFD and BMD of overhanging beams, showing the hogging moments over the supports and the sagging moment in the span.
Theory
Unlike a cantilever, a simply supported beam needs its reactions before anything else, because every section has a support on each side. Once the reactions are known, the method is the same as before: cut the beam, keep one side, and add up the vertical forces and their moments. The beam is divided into segments wherever the loading changes, at a point load, a couple or the start or end of a distributed load, and one pair of expressions for V and M is written for each segment.
The bending moment of a simply supported beam is zero at both supports, because a pin and a roller cannot resist moment, and under downward loads it is sagging in between. The largest moment occurs where the shear force is zero or changes sign, since the slope of the BMD equals the shear. For a single point load the shear changes sign under the load, giving Pab/L there, or PL/4 for a central load. For a uniform load over the whole span the shear is zero at mid-span and the moment there is wL²/8, the most used result in structural engineering.
An overhanging beam combines the two behaviours. Over the span between the supports the loads try to sag the beam, while the loads on the overhang try to rotate it about the nearer support and lift the far end, producing a hogging moment over that support equal to the cantilever moment of the overhang. The BMD therefore has a hogging peak over the support, a sagging peak in the span (if the span is long enough), and between them a point where the moment changes sign, called a point of contraflexure, treated fully in lesson 2.5.
These diagrams decide how members are built. In a simply supported RCC beam the main steel goes at the bottom and is heaviest near mid-span; in an overhanging beam extra top steel is needed over the support and into the overhang. In a steel beam the section is chosen for the largest moment of either sign, and the diagrams show where splices are least harmful (regions of low moment) and where web openings are least harmful (regions of low shear). Reading SFD and BMD quickly and correctly is therefore a core skill for both exams and site work.
Derivation
- Uniform load w on a simply supported span L: by symmetry R_A = R_B = wL/2.
- At distance x from A: V = wL/2 − w x and M = (wL/2)x − w x²/2.
- Differentiating, dM/dx = wL/2 − w x = V, so M is greatest where V = 0, at x = L/2, giving M_max = wL²/4 − wL²/8 = wL²/8.
- Point load P at distance a from A (b = L − a): R_A = Pb/L, R_B = Pa/L. For x < a, V = Pb/L and M = Pbx/L; for x > a, V = −Pa/L and M = Pa(L − x)/L. The shear changes sign under the load, so M_max = Pab/L there; with a = b = L/2 it is PL/4.
- Triangular load from zero at A to w₀ at B: total w₀L/2 at 2L/3 from A, so R_A = w₀L/6 and R_B = w₀L/3. At x from A: V = w₀L/6 − w₀x²/(2L) and M = w₀Lx/6 − w₀x³/(6L).
- Setting V = 0 gives x = L/√3 = 0.577L, and M_max = w₀L²/(9√3) ≈ 0.0642 w₀L².
- Overhanging beam, span L between supports with an overhang a at each end and a uniform load w over the whole length L + 2a: each reaction is w(L + 2a)/2. The support moment is the overhang cantilever moment, −wa²/2, and the mid-span moment is wL²/8 − wa²/2, which is zero when L = 2a.
Central point load: R = P/2; M_max = PL/4 at mid-spanPoint load at a from A: R_A = Pb/L, R_B = Pa/L; M_max = Pab/L under the loadUDL over the span: R = wL/2; V = w(L/2 − x); M = wx(L − x)/2; M_max = wL²/8 at mid-spanTriangular load 0 at A to w₀ at B: R_A = w₀L/6, R_B = w₀L/3; zero shear at x = L/√3; M_max = w₀L²/(9√3)Equal overhangs a with UDL w over L + 2a: support moment −wa²/2; mid-span moment wL²/8 − wa²/2Key relation (x from the left): dM/dx = V; M_max where V = 0 or changes signUnits: kN, m, kN/m, kN·m
- The beam is statically determinate (one pin and one roller) and the supports do not settle.
- Loads act vertically in the plane of bending; horizontal reaction is zero.
- Small deflections: the geometry of the unloaded beam is used for all lever arms.
- Point loads and couples act at single points; the SFD jumps at a point load and the BMD jumps at a couple.
- Moving loads (vehicles, cranes) need influence lines to find the worst position; the diagrams here are for one fixed load arrangement.
Codes and standards
Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.
- The shear force and bending moment of a determinate beam follow from equilibrium alone; no design code governs the mechanics.
- IS 456:2000 cl. 22.2 (a) sets the effective span used for a simply supported RCC beam (clear span plus effective depth, or centre-to-centre of supports, whichever is less), applied in Example 1.
- IS 456:2000 cl. 19.2.1 gives 25 kN/m³ for reinforced concrete self-weight, also used in Example 1.
- Side by side, not ranked: EN 1992-1-1 and ACI 318 define the span for analysis in their own terms; the shear and moment for a given span and load are the same in every system, because they come from statics.
Worked examples
Problem. The simply supported RCC beam of lesson 2.1, Example 1, has an effective span of 4.23 m and carries a total characteristic load of 14.5875 kN/m. Find the maximum shear force and bending moment and draw the diagrams.
- Reactions R_A = R_B = wL/2 = 14.5875 × 4.23/2 = 30.85 kN, so V_max = 30.85 kN at the supports.
- V = 30.85 − 14.5875x; V = 0 at x = 2.115 m (mid-span).
- M_max = wL²/8 = 14.5875 × 4.23²/8 = 14.5875 × 17.8929/8 = 32.63 kN·m (sagging) at mid-span.
- SFD: straight line from +30.85 kN at A to −30.85 kN at B. BMD: symmetric parabola, zero at the supports, 32.63 kN·m at mid-span.
- For design these characteristic values are multiplied by the load factor of the design code; the shapes of the diagrams do not change.
Answer. V_max = 30.85 kN; M_max = 32.63 kN·m sagging at mid-span
Problem. A simply supported beam AB of span 6 m carries a uniform load of 10 kN/m over the whole span and a point load of 30 kN at 2 m from A. Find the reactions, the position and value of the maximum bending moment, and draw the SFD and BMD.
- Moments about A: R_B × 6 = 10 × 6 × 3 + 30 × 2 = 180 + 60 = 240, so R_B = 40 kN; R_A = 60 + 30 − 40 = 50 kN.
- For 0 ≤ x < 2 m: V = 50 − 10x; just left of the load V = 30 kN.
- Just right of the load V = 30 − 30 = 0, and for 2 < x ≤ 6 m: V = 20 − 10x, so V = −40 kN at B.
- The shear becomes zero at the load (x = 2 m), so M_max = 50 × 2 − 10 × 2²/2 = 100 − 20 = 80 kN·m.
- Check from B: M at x = 2 m = 40 × 4 − 10 × 4²/2 = 160 − 80 = 80 kN·m.
- BMD: parabolic segments, zero at A and B, peak 80 kN·m at 2 m from A (with a change of slope under the point load).
Answer. R_A = 50 kN, R_B = 40 kN; M_max = 80 kN·m at 2 m from A
Problem. A steel beam of a loading platform rests on two columns A and B, 6 m apart, and overhangs 2 m beyond B to a free end C. It carries 12 kN/m over its whole 8 m length. Find the reactions, draw the SFD and BMD, and find the largest sagging and hogging moments.
- Moments about A: R_B × 6 = 12 × 8 × 4 = 384, so R_B = 64 kN; R_A = 96 − 64 = 32 kN.
- Span AB: V = 32 − 12x, zero at x = 32/12 = 2.667 m; just left of B, V = 32 − 72 = −40 kN.
- At B the reaction lifts the shear to −40 + 64 = 24 kN, which falls linearly to zero at C.
- Largest sagging moment at x = 2.667 m: M = 32 × 2.667 − 12 × 2.667²/2 = 85.33 − 42.67 = 42.67 kN·m.
- Hogging moment over B: M_B = −12 × 2²/2 = −24 kN·m (check from A: 32 × 6 − 12 × 6²/2 = 192 − 216 = −24 kN·m).
- The moment changes sign where 32x − 6x² = 0, at x = 5.333 m from A, a point of contraflexure (lesson 2.5).
Answer. R_A = 32 kN, R_B = 64 kN; sagging 42.67 kN·m at 2.667 m from A; hogging 24 kN·m over B
Step-by-step procedure
- Find the reactions from moments about each support in turn; check that they add up to the total load.
- Divide the beam into segments at every point load, couple, support and change of distributed load.
- For each segment write V(x) and M(x) using the forces to the left of the section (x from the left end).
- Find the sections where V = 0 or changes sign; evaluate M there and at all segment ends, support points and free ends.
- Draw the SFD and BMD to the same horizontal scale under the beam, with values and signs marked.
- Check: M = 0 at the simple supports and free ends; the slope of the BMD equals the shear; the jump in the SFD at a support equals the reaction.
Site notes
- In simply supported RCC beams the bottom bars are heaviest near mid-span; bars must not be curtailed where the moment is still large, so follow the bar bending schedule exactly.
- Overhanging beams and slabs need top steel over the support and along the overhang; this steel is easily displaced during concreting and must be checked on chairs before the pour.
- Service openings through a beam web must suit both diagrams: near mid-span of a uniformly loaded simply supported beam the shear is small but the moment is largest, so any opening is kept near mid-depth, close to the neutral axis; near the supports the shear is largest, so openings there are avoided unless designed for.
- When temporary loads are placed on a beam (stacked materials, a mobile crane outrigger on a slab), check them as point loads with Pab/L, not as an equivalent uniform load.
- Taking the maximum moment at mid-span for an unsymmetrical load instead of at the zero-shear section.
- Missing the change of sign of the shear under a point load, as in Example 2, and searching in the wrong segment.
- Ignoring the hogging moment over the support of an overhanging beam, and providing no top steel.
- Using wL²/8 for a triangular load (the correct value is w₀L²/(9√3) at 0.577L from the zero end).
- Leaving out the jump at the support when drawing the SFD of an overhanging beam.
Under the same total load W on a simply supported span L, the maximum moment is WL/4 for a central point load, WL/8 for a uniform load and about 0.128WL for a triangular load (0.0642 w₀L² with W = w₀L/2). If a computed maximum lies outside these limits for a similar load, recheck the reactions.
Summary
- Find reactions first; then V and M segment by segment.
- Maximum moment where shear is zero or changes sign.
- PL/4, Pab/L, wL²/8 and w₀L²/(9√3) are the standard results.
- Overhangs create hogging moments over the support equal to the overhang cantilever moment.
Practice questions
Tap a question to see the answer.
1A simply supported beam of span 5 m carries a central point load of 40 kN. Find the maximum shear and bending moment.
V_max = 20 kN; M_max = 40 × 5/4 = 50 kN·m at mid-span.
2A simply supported beam of span 6 m carries a 60 kN point load at 2 m from A. Find the reactions and the maximum moment.
R_A = 60 × 4/6 = 40 kN; R_B = 20 kN; M_max = Pab/L = 60 × 2 × 4/6 = 80 kN·m under the load.
3A simply supported beam of span 8 m carries 15 kN/m over its whole length. Find the reactions and the maximum moment.
R = 15 × 8/2 = 60 kN each; M_max = 15 × 64/8 = 120 kN·m at mid-span.
4A simply supported beam of span 6 m carries a triangular load rising from zero at A to 18 kN/m at B. Find the reactions, the section of zero shear and the maximum moment.
R_A = 18 × 6/6 = 18 kN; R_B = 18 × 6/3 = 36 kN; zero shear at 6/√3 = 3.464 m from A; M_max = 18 × 36/(9√3) = 41.57 kN·m.
5A beam rests on supports 4 m apart with a 2 m overhang beyond each support, and carries a uniform load w over its whole 8 m length. Find the moment over the supports and at mid-span.
Support moment = −w × 2²/2 = −2w; mid-span moment = w × 4²/8 − 2w = 0. With L = 2a the mid-span moment is exactly zero.
6A simply supported beam AB of span 6 m carries only a clockwise couple of 30 kN·m applied at 2 m from A. Find the reactions and the bending moment on each side of the couple.
R_B = 30/6 = 5 kN upward and R_A = 5 kN downward. V = −5 kN throughout. M just left of the couple = −5 × 2 = −10 kN·m; just right = −10 + 30 = +20 kN·m; M returns to zero at B.
References
Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.
- B. J. Goodno, J. M. Gere, Mechanics of Materials, Cengage Learning, 9th edition, 2018.
- R. C. Hibbeler, Mechanics of Materials, Pearson, 10th edition, 2016.
- F. P. Beer, E. R. Johnston, J. T. DeWolf, D. F. Mazurek, Mechanics of Materials, McGraw Hill, 8th edition, 2020.
- E. P. Popov, Engineering Mechanics of Solids, Prentice Hall, 2nd edition, 1998.