2.4 Load-shear-moment relations
After this lesson you should be able to:
- State and derive the differential relations between load intensity, shear force and bending moment, dV/dx = −w and dM/dx = V.
- Use the area of the load diagram to step the SFD, and the area of the SFD to step the BMD, without writing a full equation for every segment.
- Predict the shape of each diagram (constant, linear, parabolic, cubic) from the loading, and handle the jumps caused by point loads and applied couples.
Theory
Lessons 2.2 and 2.3 found shear force and bending moment by cutting the beam and writing equilibrium for each segment. That always works, but it is slow for beams with several loads. Looking at a very short slice of the beam gives two simple rules that link the load, the shear and the moment, and these rules let the diagrams be drawn almost directly from the loading.
Take a slice of length dx carrying a downward load w per metre, with the sign convention used in this book: shear is the sum of upward forces to the left of the section, and sagging moment is positive. Vertical equilibrium of the slice shows that the shear falls at a rate equal to the load intensity, dV/dx = −w. Moment equilibrium of the same slice, ignoring the second-order term w dx²/2, shows that the moment changes at a rate equal to the shear, dM/dx = V. In words, the slope of the SFD is minus the load intensity, and the slope of the BMD is the shear force.
Integrating these rules between two sections gives the area method. The change in shear between two sections equals minus the area of the load diagram between them, and the change in moment equals the area of the SFD between them. A point load is not covered by the integral, so it makes the SFD jump down by the load; an applied clockwise couple makes the BMD jump up by the couple. Because the moment changes at the rate V, the BMD has a peak or a trough wherever the SFD crosses zero, which is why the maximum moment is always looked for at the zero-shear section.
The rules also fix the shape of each piece. Where there is no distributed load the shear is constant and the moment is a straight line. Under a uniform load the shear is a straight line and the moment is a parabola. Under a linearly varying load the shear is a parabola and the moment is a cubic curve. Where the shear is zero over a length, the moment is constant, which is the state of pure bending used in lesson 3.1. These facts are the fastest check on any diagram drawn by hand or produced by software.
Derivation
- Consider a slice between x and x + dx under a downward distributed load w(x). The left face carries shear V and moment M; the right face carries V + dV and M + dM.
- Vertical equilibrium (upward positive): V − w dx − (V + dV) = 0, so dV/dx = −w.
- Moments about the right face: M + V dx − w dx (dx/2) − (M + dM) = 0. Dropping the second-order term gives dM/dx = V.
- Combining the two: d²M/dx² = −w.
- Integrating from section 1 to section 2: V₂ − V₁ = −∫w dx (minus the load-diagram area) and M₂ − M₁ = ∫V dx (the SFD area).
- At a downward point load P the slice argument gives V₂ − V₁ = −P (a jump in the SFD); at a clockwise couple C it gives M₂ − M₁ = +C (a jump in the BMD).
- Check on lesson 2.3, Example 2 (span 6 m, 10 kN/m and 30 kN at 2 m, R_A = 50 kN): the SFD falls from 50 to 30 kN over the first 2 m, area (50 + 30)/2 × 2 = 80 kN·m, so M = 80 kN·m at 2 m, as found by equations.
dV/dx = −w (slope of SFD = minus load intensity)dM/dx = V (slope of BMD = shear force)d²M/dx² = −wV₂ − V₁ = −(area of load diagram from 1 to 2)M₂ − M₁ = +(area of SFD from 1 to 2)Point load P downward: SFD jumps by −P; clockwise couple C: BMD jumps by +CShapes: no load, V constant and M linear; UDL, V linear and M parabolic; linear load, V parabolic and M cubicUnits: w in kN/m, V in kN, M in kN·m
- Loads act in the plane of bending and the beam axis is straight.
- Small deflections, so the slice length dx is measured along the unloaded axis.
- w is positive downward; with an upward load the sign of dV/dx reverses.
- The relations hold between point loads and couples; at those points the jump rules are used instead.
- The sign convention must be the same for all three diagrams; with the opposite shear convention dM/dx = −V.
Codes and standards
Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.
- The load-shear-moment relations are pure statics and are not set by any design code.
- Codes use them indirectly: IS 456:2000 and IS 800:2007 both design for the shear force and bending moment found by analysis, and the zero-shear section located here is where the design moment of a simply supported member is taken.
- Side by side, not ranked: EN 1992-1-1, EN 1993-1-1 and ACI 318 use the same statics; only the load combinations and resistances differ between systems.
Worked examples
Problem. A simply supported beam AB of span 8 m carries a uniform load of 20 kN/m over the left 4 m (A to C). Draw the SFD and BMD using the area method and find the maximum bending moment.
- Moments about A: R_B × 8 = 20 × 4 × 2 = 160, so R_B = 20 kN; R_A = 80 − 20 = 60 kN.
- SFD: starts at +60 kN at A and falls at 20 kN/m (slope −w) to 60 − 80 = −20 kN at C; from C to B there is no load, so V stays at −20 kN until R_B brings it back to zero.
- Zero shear at x = 60/20 = 3 m from A.
- Area of SFD from A to 3 m = ½ × 3 × 60 = 90 kN·m, so M_max = 90 kN·m at 3 m.
- From 3 m to C the area is −½ × 1 × 20 = −10 kN·m, so M_C = 80 kN·m; from C to B the area is −20 × 4 = −80 kN·m, so M_B = 0, as it must be.
- Shapes: parabola from A to C (under the UDL), straight line from C to B (no load).
Answer. R_A = 60 kN, R_B = 20 kN; M_max = 90 kN·m at 3 m from A; M_C = 80 kN·m
Problem. A simply supported steel beam of span 5 m carries a pipe bracket fixed to it at 2 m from A. The bracket holds a 20 kN load whose line of action is 0.5 m to the right of the fixing point. Find the reactions and draw the SFD and BMD, and compare the maximum moment with the value obtained if the eccentricity is ignored.
- Replace the bracket load by a 20 kN downward force at 2 m plus a clockwise couple of 20 × 0.5 = 10 kN·m at the same point.
- Moments about A: R_B × 5 = 20 × 2 + 10 = 50, so R_B = 10 kN; R_A = 20 − 10 = 10 kN.
- SFD: +10 kN from A to the bracket, a jump of −20 kN to −10 kN, then −10 kN to B.
- BMD: just left of the bracket M = 10 × 2 = 20 kN·m; the clockwise couple lifts it by 10 to 30 kN·m just right of the bracket; the SFD area from there to B is −10 × 3 = −30 kN·m, so M_B = 0.
- Maximum moment = 30 kN·m just right of the bracket.
- Ignoring the eccentricity, Pab/L = 20 × 2 × 3/5 = 24 kN·m, an underestimate of 20 per cent.
Answer. R_A = R_B = 10 kN; M_max = 30 kN·m (24 kN·m if the eccentricity is wrongly ignored)
Problem. A simply supported beam of span 6 m carries a load rising linearly from zero at A to 18 kN/m at B. Use the differential relations to find V(x) and M(x), the section of zero shear and the maximum moment.
- Load intensity w(x) = 18x/6 = 3x kN/m; total load 54 kN at 4 m from A, so R_A = 54 × 2/6 = 18 kN and R_B = 36 kN.
- Integrate dV/dx = −3x with V(0) = 18: V = 18 − 1.5x² (a parabola).
- Integrate dM/dx = V with M(0) = 0: M = 18x − 0.5x³ (a cubic). Check: M(6) = 108 − 108 = 0.
- V = 0 at x² = 12, x = 3.464 m (= L/√3).
- M_max = 18 × 3.464 − 0.5 × 3.464³ = 62.35 − 20.78 = 41.57 kN·m, matching w₀L²/(9√3) from lesson 2.3.
Answer. V = 18 − 1.5x², M = 18x − 0.5x³; M_max = 41.57 kN·m at 3.464 m from A
Step-by-step procedure
- Find the reactions.
- Draw the SFD from left to right: jump at each point load and reaction, slope −w under distributed loads, flat where there is no load.
- Mark every point where the SFD crosses zero.
- Draw the BMD from left to right: start at the known end value, add the SFD area segment by segment, add a jump at every applied couple.
- Check that the BMD closes at the known value at the far end (zero at a simple support or free end).
- Check the shapes: straight, parabolic or cubic as the loading requires, with peaks only at zero shear or at couples.
Site notes
- When checking a software output for a beam, look at the BMD shape first: a straight-line BMD under a beam that carries a slab load, or a curved one between two point loads, means the load was entered wrongly.
- Brackets, cantilevered pipe supports and eccentric crane rails apply couples as well as forces; include the couple, as in Example 2, or the moment can be underestimated.
- The zero-shear section is where the bottom steel of a simply supported beam is busiest; avoid laps and web openings there.
- In a four-point bending test (two equal loads at the third points) the shear between the loads is zero, so the moment is constant there; this is why flexure tests of concrete prisms use that arrangement.
- Using dM/dx = V with a shear convention that is opposite to the one used for drawing, which turns every slope the wrong way.
- Forgetting the jump in the BMD at an applied couple, and closing the diagram with an error equal to the couple.
- Treating an eccentric bracket load as a simple point load.
- Drawing a parabola for the BMD between point loads where there is no distributed load (it must be straight).
- Adding the area of the load diagram to the BMD instead of the area of the SFD.
Close the diagrams: the total area of the load diagram plus all point loads must equal the sum of the reactions, and the total area of the SFD plus all applied clockwise couples must bring the moment back to its known end value. If either does not close, a load or a reaction is wrong.
Summary
- dV/dx = −w and dM/dx = V, with shear positive upward on the left and sagging moment positive.
- Change in V = minus load-diagram area; change in M = SFD area.
- Point loads jump the SFD; couples jump the BMD.
- No load: V flat, M straight; UDL: V straight, M parabolic; linear load: V parabolic, M cubic.
Practice questions
Tap a question to see the answer.
1A simply supported beam of span 4 m carries 12 kN/m over its whole length. Using the area of the SFD, find the moment at mid-span.
R = 24 kN each. The SFD falls from 24 kN to zero over 2 m, area ½ × 2 × 24 = 24 kN·m, so M = 24 kN·m (= wL²/8).
2A cantilever of length 3 m, fixed at A, carries 10 kN/m over its length. Using the area of the SFD from A to the free end, find the fixing moment.
V at A = 30 kN, falling linearly to zero at the free end. Area = ½ × 3 × 30 = 45 kN·m. Since M = 0 at the free end, M_A = 0 − 45 = −45 kN·m (hogging).
3Under what loading is the BMD of a beam segment a cubic curve, and what shape is the SFD there?
Under a linearly varying (triangular or trapezoidal) distributed load; the SFD is then a parabola.
4The SFD of a simply supported beam of span 8 m is +15 kN from A to C (2 m from A) and −5 kN from C to B. What load acts on the beam and what is the maximum moment?
A single downward point load of 15 − (−5) = 20 kN at C. M_max = 15 × 2 = 30 kN·m at C (check from B: 5 × 6 = 30 kN·m).
5Over a 3 m segment the shear changes linearly from +40 kN to −20 kN. Find the uniform load on the segment, where the moment is greatest and by how much it rises from the start of the segment to that point.
w = (40 − (−20))/3 = 20 kN/m. V = 0 at 40/20 = 2 m from the start. Rise in M = ½ × 2 × 40 = 40 kN·m.
6A simply supported beam of span 6 m carries two loads of 30 kN at 2 m and 4 m from A. Describe the SFD and BMD between the loads.
R_A = R_B = 30 kN. V = 30 kN from A to the first load, zero between the loads and −30 kN after the second. Between the loads M is constant at 30 × 2 = 60 kN·m (pure bending).
References
Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.
- B. J. Goodno, J. M. Gere, Mechanics of Materials, Cengage Learning, 9th edition, 2018.
- R. C. Hibbeler, Mechanics of Materials, Pearson, 10th edition, 2016.
- F. P. Beer, E. R. Johnston, J. T. DeWolf, D. F. Mazurek, Mechanics of Materials, McGraw Hill, 8th edition, 2020.
- E. P. Popov, Engineering Mechanics of Solids, Prentice Hall, 2nd edition, 1998.