Indiacon CivilSubscribe

Textbook › Strength of Materials › Chapter 2 › Lesson 2.2

2.2 SFD and BMD of cantilevers

Strength of Materials Chapter 2: Shear force and bending moment Under review — not yet three-checked Author: Indiacon

Learning objectives

After this lesson you should be able to:

  • Define shear force and bending moment at a section of a beam, and apply a consistent sign convention (sagging moment positive, hogging negative).
  • Write the shear force and bending moment as functions of position for a cantilever carrying point loads, a uniformly distributed load and a uniformly varying load.
  • Draw the shear force and bending moment diagrams of a cantilever, and read off the maximum values and where they occur.

Theory

Cut a loaded beam at any section and look at one side. That piece is in equilibrium only because the other side holds it with a vertical force and a moment acting across the cut. The vertical force is the shear force V at the section, and the moment is the bending moment M. The shear force at a section equals the sum of all the vertical forces on one side of it; the bending moment equals the sum of the moments of all the forces on one side, taken about the section. Either side may be used, and both give the same answer, which is a useful check.

Signs must be fixed once and kept. In this textbook a bending moment is positive (sagging) when it makes the beam concave upwards, so the bottom fibres are in tension, and negative (hogging) when the top fibres are in tension. A shear force is positive when the resultant of the forces to the left of the section acts upwards (equivalently, the forces to the right act downwards). With x measured from the left end, these conventions give the relation dM/dx = V that is used throughout this chapter and proved in lesson 2.4.

w per metrefree endfixedV = wLSFDM = −wL²/2 (hogging)BMDIndiacon original, not to scale
Figure 2.2: Cantilever with a uniform load: the shear grows linearly and the hogging moment as a parabola towards the fixed end. Indiacon original, not to scale.

A cantilever is the simplest case because it needs no reactions to be found first: if we look at the part between the section and the free end, all the forces on it are known loads. For a point load P at the free end the shear is P everywhere and the moment grows linearly from zero at the tip to PL at the support. For a uniform load w the shear grows linearly (wx) and the moment as a parabola (wx²/2). For a load that grows linearly from the tip, the shear varies as x² and the moment as x³. In every case the moment is hogging and is largest at the fixed end.

This is why cantilever slabs, balconies, chajjas and retaining wall stems carry their main reinforcement near the top or near the face retaining the soil, and why that steel must run well into the support. It is also why the support of a cantilever is the critical section for both shear and moment: the fixed end must resist the whole load and its whole moment. A mistake in placing the steel at the bottom, as in a simply supported slab, is one of the classic causes of cantilever failures on site.

Derivation

  1. Cantilever of length L fixed at A (left) and free at B (right). Let x be the distance of a section from the free end B and consider the part between the section and B.
  2. Point load P at B: vertical equilibrium of that part gives V = P (positive, constant). Moments about the section give M = −P x (hogging); at the support M_A = −PL.
  3. Uniform load w over the whole length: the part carries w x acting at x/2, so V = w x and M = −w x²/2; at the support V = wL and M = −wL²/2.
  4. Uniformly varying load, zero at the free end and w₀ at the fixed end: intensity at distance x from B is w₀x/L. The load on the part is w₀x²/(2L), acting at x/3 from the section, so V = w₀x²/(2L) and M = −(w₀x²/2L)(x/3) = −w₀x³/(6L); at the support V = w₀L/2 and M = −w₀L²/6.
  5. Fixed-end reactions follow from the same equations at x = L: vertical reaction R_A = total load and fixing moment M_A equal to the support moment, acting to keep the beam from rotating.
  6. Check with x′ = L − x measured from the fixed end A: for the tip load M = −P(L − x′), so dM/dx′ = P = V; for the uniform load M = −w(L − x′)²/2, so dM/dx′ = w(L − x′) = V. The rate of change of moment equals the shear.
Formulas, symbols and SI units
  • Tip load P: V = P; M = −P x; maximum M = −PL at the fixed end
  • UDL w over full length: V = w x; M = −w x²/2; maximum V = wL, M = −wL²/2
  • Triangular load 0 at tip to w₀ at support: V = w₀x²/(2L); M = −w₀x³/(6L); maximum V = w₀L/2, M = −w₀L²/6
  • Fixed-end reaction R_A = total load; fixing moment |M_A| = sum of (load × distance from support)
  • x measured from the free end; V in kN, M in kN·m, w in kN/m, L in m
  • Shape rule: no load → V constant, M linear; uniform load → V linear, M parabolic; linearly varying load → V parabolic, M cubic
Assumptions and limits
  • The beam is straight and the loads act at right angles to it in the plane of bending.
  • The fixed end is fully rigid; a support that rotates slightly does not change V and M (the beam is determinate) but increases the tip deflection.
  • Small deflections: lever arms are measured on the undeformed beam.
  • Self-weight is included as part of the uniform load when it is significant.
  • Point loads are idealised as acting at a single point; the shear diagram jumps there by the load.

Codes and standards

Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.

  • Shear force and bending moment in a cantilever follow from equilibrium alone; no design code governs the mechanics.
  • The loads in Example 1 use IS 456:2000 cl. 19.2.1 (reinforced concrete 25 kN/m³) and IS 875 (Part 2):1987 cl. 3.1 and Table 1, which gives 3.0 kN/m² for balconies of dwelling houses together with a line load of 1.5 kN per metre run at the outer edge, the two not being taken to act at the same time.
  • Side by side, not ranked: Eurocode practice takes balcony and floor loads from EN 1991-1-1 and American practice from ASCE/SEI 7; each is used with its own load factors, so values are not mixed between systems.
  • Earth pressure on a cantilever wall stem (Example 3) is found from Rankine's theory, covered in the soil mechanics subject; the wall design itself belongs to the RCC subject.

Worked examples

Example 1 (site style: balcony slab)

Problem. A reinforced concrete balcony slab projects 1.2 m from a beam and is 150 mm thick, with 1.0 kN/m² of floor finish. Take a 1 m wide strip. Using 25 kN/m³ for the concrete and the IS 875 (Part 2) balcony load for a dwelling house, find the shear force and bending moment at the support for (a) the uniform imposed load and (b) the edge line load instead (characteristic loads).

  1. Dead load: 0.15 × 25 = 3.75 kN/m² slab + 1.0 kN/m² finish = 4.75 kN/m per metre width.
  2. Case (a): w = 4.75 + 3.0 = 7.75 kN/m. V = wL = 7.75 × 1.2 = 9.30 kN; M = wL²/2 = 7.75 × 1.44/2 = 5.58 kN·m (hogging).
  3. Case (b): dead UDL plus 1.5 kN at the tip. V = 4.75 × 1.2 + 1.5 = 7.20 kN; M = 4.75 × 1.44/2 + 1.5 × 1.2 = 3.42 + 1.80 = 5.22 kN·m (hogging).
  4. Case (a) governs both shear and moment here. The moment is hogging, so the main steel goes at the top of the slab and must be anchored well into the supporting beam or back span.

Answer. Support V = 9.30 kN and M = 5.58 kN·m hogging per metre width (uniform imposed load governs)

Example 2 (exam style: mixed loads)

Problem. A cantilever AB is 3 m long, fixed at A and free at B. It carries a uniform load of 10 kN/m over its full length, a point load of 20 kN at B and a point load of 15 kN at 1 m from A. Find the shear force and bending moment at B, at the 15 kN load and at A, and draw the diagrams.

  1. Measure x from B. For 0 ≤ x < 2 m: V = 20 + 10x; M = −(20x + 5x²).
  2. At B (x = 0): V = 20 kN, M = 0.
  3. At x = 2 m (just on the B side of the 15 kN load): V = 20 + 20 = 40 kN; M = −(40 + 20) = −60 kN·m. Just on the A side, V jumps by 15 to 55 kN; M is continuous.
  4. For 2 < x ≤ 3 m: V = 35 + 10x; M = −(20x + 5x² + 15(x − 2)). At A (x = 3): V = 65 kN; M = −(60 + 45 + 15) = −120 kN·m.
  5. SFD: rises linearly from 20 to 40 kN, jumps to 55 kN, rises linearly to 65 kN at A. BMD: hogging throughout, curving from 0 at B to −60 kN·m and −120 kN·m at A.
  6. Check: fixing moment = 10 × 3 × 1.5 + 20 × 3 + 15 × 1 = 45 + 60 + 15 = 120 kN·m; reaction = 30 + 20 + 15 = 65 kN.

Answer. At A: V = 65 kN, M = 120 kN·m hogging; at the 15 kN load M = 60 kN·m hogging; at B: V = 20 kN, M = 0

Example 3 (site style: retaining wall stem)

Problem. The stem of a cantilever retaining wall retains 3 m of dry soil with a unit weight of 18 kN/m³ and an active earth pressure coefficient of 1/3 (Rankine, φ = 30°, level backfill, no surcharge). Per metre run, find the shear force and bending moment at the base of the stem and at mid-height.

  1. Pressure rises from zero at the top to w₀ = K_a γ H = (1/3) × 18 × 3 = 18 kN/m² at the base, a triangular load of 18 kN/m per metre run.
  2. The stem is a vertical cantilever fixed at the base, with x measured down from the top (the free end).
  3. At the base: V = w₀H/2 = 18 × 3/2 = 27 kN; M = w₀H²/6 = 18 × 9/6 = 27 kN·m (tension on the soil face).
  4. At mid-height (x = 1.5 m): V = w₀x²/(2H) = 18 × 2.25/6 = 6.75 kN; M = w₀x³/(6H) = 18 × 3.375/18 = 3.375 kN·m.
  5. The moment at mid-height is only 1/8 of the base value (cubic variation), which is why stem steel can be curtailed in the upper part.

Answer. Base V = 27 kN and M = 27 kN·m per metre run; at mid-height V = 6.75 kN and M = 3.375 kN·m

Step-by-step procedure

  1. Sketch the cantilever with all loads; measure x from the free end so that no reactions are needed.
  2. Mark the points where the loading changes (point loads, start or end of a distributed load); write V and M for each segment between them.
  3. For each segment, V = sum of the loads between the section and the free end; M = −sum of (load × distance to the section).
  4. Evaluate V and M at the free end, at each change point (both sides of a point load for V) and at the support.
  5. Draw the SFD and BMD under the beam to the same horizontal scale, using straight lines, parabolas or cubics as the loading requires.
  6. Check: the support values equal the total load and the total moment of the loads about the support.

Site notes

  • Main steel of cantilever slabs, chajjas and balconies goes at the top; check on site before concreting that it has not been walked down by workers or placed at the bottom by mistake.
  • Props under a cantilever are removed only after the concrete and the holding-down back span have gained strength; early removal is a known cause of collapse.
  • Do not let materials be stacked at the tip of a fresh cantilever slab; a tip load causes a larger support moment than the same load spread out.
  • For retaining walls, keep weep holes and drains clear; water pressure behind the stem adds a second triangular load and can more than double the base moment.
Common mistakes
  • Taking the cantilever moment as sagging and placing steel at the bottom.
  • Using wL²/8 (the simply supported value) for a cantilever instead of wL²/2.
  • For a triangular load, putting the resultant at L/2 or using w₀L²/2 or w₀L²/3 instead of w₀L²/6.
  • Forgetting that a point load causes a jump in the SFD but no jump in the BMD.
  • Measuring x from the fixed end without first finding the fixing moment and reaction, which leads to sign errors.
Quick check

The fixing moment of a cantilever equals the total load times the distance of its resultant from the support: WL for a tip load, WL/2 for a uniform load and WL/3 for a triangular load peaking at the support. It can never exceed W times the length.

Summary

  • Shear force = sum of vertical forces on one side; bending moment = sum of their moments about the section.
  • Cantilever moments are hogging and largest at the fixed end.
  • Tip load: PL; uniform load: wL²/2; triangular load peaking at the support: w₀L²/6.
  • SFD and BMD shapes follow the load: none → constant and linear; uniform → linear and parabolic; triangular → parabolic and cubic.

Practice questions

Tap a question to see the answer.

1A cantilever 2 m long carries a 10 kN point load at its free end. Find the maximum shear force and bending moment.

V = 10 kN throughout; M = 10 × 2 = 20 kN·m hogging at the fixed end.

2A cantilever 4 m long carries a uniform load of 5 kN/m over its whole length. Find the support shear and moment.

V = 5 × 4 = 20 kN; M = 5 × 16/2 = 40 kN·m hogging.

3A cantilever 3 m long carries 6 kN/m only over the 1.5 m nearest the free end. Find the support shear and moment, and the shear in the unloaded part.

Load = 9 kN at 0.75 m from the tip, i.e. 2.25 m from the support. V = 9 kN (constant over the unloaded 1.5 m); M = 9 × 2.25 = 20.25 kN·m hogging.

4A cantilever 3 m long carries a triangular load rising from zero at the free end to 12 kN/m at the fixed end. Find the support shear and moment.

V = 12 × 3/2 = 18 kN; M = 12 × 9/6 = 18 kN·m hogging.

5What are the shapes of the SFD and BMD of a cantilever carrying a uniform load over its whole length?

SFD: straight line from zero at the tip to wL at the support. BMD: second-degree parabola from zero at the tip to wL²/2 (hogging) at the support.

6A cantilever 2 m long has only a couple of 8 kN·m applied at its free end. Describe the SFD and BMD.

Shear force is zero everywhere (no vertical loads); bending moment is constant at 8 kN·m along the whole length, and the fixing moment is 8 kN·m.

References

Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.

  • B. J. Goodno, J. M. Gere, Mechanics of Materials, Cengage Learning, 9th edition, 2018.
  • R. C. Hibbeler, Mechanics of Materials, Pearson, 10th edition, 2016.
  • F. P. Beer, E. R. Johnston, J. T. DeWolf, D. F. Mazurek, Mechanics of Materials, McGraw Hill, 8th edition, 2020.
  • E. P. Popov, Engineering Mechanics of Solids, Prentice Hall, 2nd edition, 1998.
Suggest a correction

If something on this page is wrong, tell the editor. Your message is sent privately and is not published.

Sent privately to the Indiacon editor; not published.