Indiacon CivilSubscribe

Textbook › Strength of Materials › Chapter 2 › Lesson 2.1

2.1 Beams, supports and loads

Strength of Materials Chapter 2: Shear force and bending moment Under review — not yet three-checked Author: Indiacon

Learning objectives

After this lesson you should be able to:

  • Name the common beam types (simply supported, cantilever, overhanging, fixed, propped cantilever and continuous) and the reactions that each support provides.
  • Replace point loads, uniformly distributed loads, uniformly varying and trapezoidal loads and applied couples by their resultants, and place each resultant correctly.
  • Find the support reactions of statically determinate beams from the three equations of equilibrium, and check the answer with an independent equation.

Theory

A beam is a member that carries loads mainly at right angles to its length and passes them sideways to its supports by bending. Floor beams, lintels, bridge girders, purlins, crane rails and the stem of a retaining wall are all beams, even though they look very different. Before we can find the stresses inside any of them, we must know the forces that act on them: the applied loads and the reactions that the supports push back with. This lesson sets up that first step, which every later chapter on bending, shear and deflection depends on.

Supports are idealised by the movements they prevent. A roller (or a rocker, or a beam resting on a sliding bearing) prevents movement at right angles to its surface only, so it supplies one reaction. A pin or hinge prevents movement in any direction but allows rotation, so it supplies two reaction components. A fixed support, such as a beam built well into a wall or cast monolithically with a thick column, prevents both movement and rotation, so it supplies two force components and a moment. A simply supported beam has a pin at one end and a roller at the other; a cantilever has one fixed end and one free end; an overhanging beam is a simply supported beam that extends beyond one or both supports.

Simply supportedPpin: 2 reactionsroller: 1Cantileverwfixed end: 2 forces + momentOverhanging beam with triangular loadw₀resultant w₀a/2 at a/3 from the larger endIndiacon original, not to scale
Figure 2.1: Support types and the reactions they provide, with point, uniform and triangular loads on determinate beams. Indiacon original, not to scale.

In a plane, a rigid body has three equations of equilibrium: the sums of horizontal forces, vertical forces and moments must each be zero. A beam with exactly three independent reaction components, arranged so that they can resist any load, is statically determinate: the reactions follow from equilibrium alone. Simply supported, cantilever and overhanging beams are of this kind and are the subject of this chapter. Fixed, propped and continuous beams have more reactions than equations; they are statically indeterminate and need the deformation of the beam as well, which comes in the structural analysis subject.

Loads are idealised in the same spirit. A column standing on a transfer beam or a wheel on a girder is treated as a point load. The weight of a slab, a wall or the beam itself is a uniformly distributed load, given as force per unit length. Water or earth pressure that grows with depth is a uniformly varying (triangular) load, and a combination of the two is trapezoidal. A bracket bolted to the side of a beam can apply a couple. For finding reactions, any distributed load may be replaced by its resultant, equal to the area of the load diagram and acting through its centroid; for finding internal forces later, the distribution itself must be kept.

Derivation

  1. Uniformly distributed load w over length a: the resultant is the area of the load diagram, W = w a, acting through its centroid at a/2 from either end.
  2. Uniformly varying load from 0 to w₀ over length a: intensity at distance x from the zero end is w₀x/a. Resultant W = ∫₀ᵃ w₀x/a dx = w₀a/2.
  3. Its moment about the zero end is ∫₀ᵃ (w₀x/a)·x dx = w₀a²/3, so the resultant acts at x̄ = (w₀a²/3)/(w₀a/2) = 2a/3 from the zero end, that is a/3 from the larger end.
  4. Trapezoidal load from w₁ to w₂: split into a rectangle w₁a (at a/2) and a triangle (w₂ − w₁)a/2 (at 2a/3 from the w₁ end). Resultant W = (w₁ + w₂)a/2, at x̄ = a(w₁ + 2w₂)/[3(w₁ + w₂)] from the w₁ end.
  5. Reactions of a simply supported beam of span L with a point load P at distance a from A (b = L − a from B): taking moments about A, R_B L = P a, so R_B = P a/L; vertical equilibrium gives R_A = P − R_B = P b/L.
  6. General statically determinate beam: ΣF_x = 0 gives the horizontal reaction (zero for vertical loads only); ΣM about one support gives the other vertical reaction; ΣF_y = 0 gives the remaining one. A moment equation about the second support is used as an independent check.
  7. Determinacy check for a beam without internal hinges: with r independent reaction components, r = 3 (and properly arranged) is determinate, r > 3 is indeterminate to degree r − 3, and r < 3 is a mechanism that cannot carry general loads.
Formulas, symbols and SI units
  • UDL resultant W = w a (kN), acting at a/2; w in kN/m, a in m
  • Triangular load resultant W = w₀a/2, acting at a/3 from the larger end
  • Trapezoidal load W = (w₁ + w₂)a/2, at x̄ = a(w₁ + 2w₂)/[3(w₁ + w₂)] from the w₁ end
  • Simply supported beam, point load: R_A = P b/L, R_B = P a/L
  • Equilibrium: ΣF_x = 0, ΣF_y = 0, ΣM = 0 (moments in kN·m)
  • Determinacy of a beam without internal hinges: r = 3 determinate; r − 3 = degree of indeterminacy
  • Units: forces in kN, distributed loads in kN/m, moments in kN·m (1 kN·m = 10⁶ N·mm)
Assumptions and limits
  • The beam is treated as a rigid body when finding reactions; its small deflections do not change the lever arms of the loads.
  • Supports are ideal: rollers have no friction, pins have no moment resistance, and fixed ends are perfectly rigid. Real bearings and connections lie between these limits.
  • Loads act in the plane of the beam, through the shear centre of the section, so that the beam bends without twisting.
  • Distributed loads are replaced by resultants only for finding reactions; internal shear and moment at a section must use only the part of the load on one side of the section.
  • Spans are taken between the lines of action of the reactions; for real members the code definition of effective span is used.

Codes and standards

Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.

  • The equilibrium of beams is pure mechanics and no design code governs it; codes enter through the loads and the span used.
  • IS 456:2000 cl. 22.2 (a) takes the effective span of a simply supported beam or slab not built integrally with its supports as the clear span plus the effective depth, or the centre-to-centre distance of the supports, whichever is less.
  • IS 456:2000 cl. 19.2.1 allows dead loads to be calculated from the unit weights in IS 875 (Part 1), and takes plain and reinforced concrete as 24 kN/m³ and 25 kN/m³ unless more accurate values are warranted.
  • IS 875 (Part 2):1987 cl. 3.1 and Table 1 set minimum imposed floor loads by occupancy; for rooms and kitchens of dwelling houses the uniformly distributed load is 2.0 kN/m², with a corresponding concentrated load of 1.8 kN that is not taken to act at the same time.
  • Side by side, not ranked: Eurocode practice takes loads from EN 1991-1-1 and defines effective span in EN 1992-1-1; American practice takes loads from ASCE/SEI 7 and spans from ACI 318. Each system uses its own load values together with its own load factors, so values are not mixed between systems.

Worked examples

Example 1 (site style: load on an RCC beam)

Problem. A reinforced concrete beam 230 mm wide and 450 mm deep (effective depth 410 mm) rests on two 230 mm thick brick walls with a clear span of 4.0 m. It is not cast into the walls. Besides its own weight it carries 12 kN/m from the slab. Find the effective span, the total load per metre and the reactions (characteristic loads, no load factors).

  1. Effective span per IS 456 cl. 22.2 (a): clear span + d = 4.0 + 0.41 = 4.41 m; centre-to-centre of walls = 4.0 + 0.23 = 4.23 m; the lesser, L = 4.23 m, governs.
  2. Self-weight = 0.23 × 0.45 × 25 = 2.5875 kN/m (reinforced concrete at 25 kN/m³, IS 456 cl. 19.2.1).
  3. Total w = 12 + 2.5875 = 14.5875 kN/m ≈ 14.59 kN/m.
  4. Total load W = 14.5875 × 4.23 = 61.71 kN; by symmetry R_A = R_B = W/2 = 30.85 kN.
  5. Check: R_A + R_B = 61.71 kN equals the total load, and the moment of the load about A (61.71 × 2.115 = 130.5 kN·m) equals R_B × 4.23.

Answer. L = 4.23 m; w = 14.59 kN/m; R_A = R_B = 30.85 kN

Example 2 (exam style: point load plus triangular load)

Problem. A simply supported beam AB of span 6 m carries a point load of 20 kN at 2 m from A and a triangular load that rises from zero at A to 12 kN/m at B. Find the reactions.

  1. Triangular load resultant = ½ × 12 × 6 = 36 kN, acting at 2/3 × 6 = 4 m from A.
  2. Moments about A: R_B × 6 = 20 × 2 + 36 × 4 = 40 + 144 = 184, so R_B = 30.67 kN.
  3. Vertical equilibrium: R_A = 20 + 36 − 30.67 = 25.33 kN.
  4. Check with moments about B: R_A × 6 = 20 × 4 + 36 × 2 = 152, so R_A = 25.33 kN, as before.

Answer. R_A = 25.33 kN; R_B = 30.67 kN

Example 3 (site style: overhanging platform beam)

Problem. A steel beam ABC rests on a pin at A and a roller at B, 5 m apart, and overhangs 1.5 m beyond B to C. It carries 10 kN/m over its whole 6.5 m length and a 15 kN point load at the free end C. Find the reactions.

  1. UDL resultant = 10 × 6.5 = 65 kN at 3.25 m from A.
  2. Moments about A: R_B × 5 = 65 × 3.25 + 15 × 6.5 = 211.25 + 97.5 = 308.75, so R_B = 61.75 kN.
  3. Vertical equilibrium: R_A = 65 + 15 − 61.75 = 18.25 kN.
  4. Check with moments about B: R_A × 5 = 10 × 5 × 2.5 − 10 × 1.5 × 0.75 − 15 × 1.5 = 125 − 11.25 − 22.5 = 91.25, so R_A = 18.25 kN.
  5. The overhang load lifts end A: a longer overhang or a heavier end load could make R_A negative, so the pin would have to hold the beam down.

Answer. R_A = 18.25 kN; R_B = 61.75 kN (both upward)

Step-by-step procedure

  1. Draw the beam to a rough scale with every support, load and dimension; mark the span used for analysis.
  2. Replace each support by its reaction components (roller one, pin two, fixed end two forces and a moment), with assumed directions.
  3. Count the reactions: three properly arranged components means the beam is determinate and equilibrium is enough.
  4. Replace each distributed load by its resultant and mark where it acts.
  5. Take moments about one support to find the reaction at the other; then use ΣF_y = 0 and ΣF_x = 0.
  6. Check with a moment equation about the other support; a negative answer means the reaction acts opposite to the direction assumed.

Site notes

  • Check how the beam is actually supported on site: a beam cast monolithically with columns is not simply supported, and a beam resting on a wall without a bearing plate may crush the masonry under the reaction.
  • A cantilever needs a real fixity: the back span or the wall load holding it down must be built before the formwork props under the projection are removed.
  • Overhangs at the ends of platforms, sunshades and canopies can lift the far support; check the uplift case with the overhang loaded and the main span empty.
  • Record actual loads during construction, such as stacked bricks, cement bags or shuttering, which can exceed the design imposed load on a young slab or beam.
Common mistakes
  • Placing the resultant of a triangular load at the middle of its length instead of at one third from the larger end.
  • Giving a roller two reactions or a pin a moment, which makes a determinate beam look indeterminate.
  • Using the clear span in place of the effective span, or mixing kN with N and m with mm in the moment equation.
  • Forgetting the self-weight of the beam, which is often 10 to 20 % of the load on a concrete beam.
  • Not checking the answer with a second moment equation, so a sign error in one lever arm goes unnoticed.
Quick check

For vertical loads only, the reactions must add up to the total load. For a symmetric load on a simply supported beam, each reaction is half the total; for one point load, the nearer support takes the larger share, in proportion to the distance from the other support.

Summary

  • Roller one reaction, pin two, fixed end three.
  • Simply supported, cantilever and overhanging beams are statically determinate; fixed, propped and continuous beams are not.
  • A distributed load is replaced by its area acting at its centroid, but only for finding reactions.
  • Find reactions by moments about one support, then vertical equilibrium; check with moments about the other support.

Practice questions

Tap a question to see the answer.

1Find the resultant of a uniformly distributed load of 8 kN/m acting over 5 m, and state where it acts.

W = 8 × 5 = 40 kN, acting at 2.5 m from either end of the loaded length.

2A triangular load rises from zero to 9 kN/m over 6 m. Find the resultant and its position.

W = ½ × 9 × 6 = 27 kN, acting at 4 m from the zero end (2 m from the larger end).

3A simply supported beam of span 8 m carries a 40 kN point load at 3 m from A. Find the reactions.

R_A = 40 × 5/8 = 25 kN; R_B = 40 × 3/8 = 15 kN.

4How many reaction components do a roller, a pin and a fixed support provide? Is a beam on a pin and a roller statically determinate?

Roller 1, pin 2, fixed 3. A pin plus a roller gives r = 3, so the beam is statically determinate.

5A trapezoidal load varies from 4 kN/m to 10 kN/m over 3 m. Find the resultant and its distance from the 4 kN/m end.

W = (4 + 10)/2 × 3 = 21 kN; x̄ = 3 × (4 + 20)/(3 × 14) = 1.714 m from the 4 kN/m end.

6Floor beams in a dwelling house are spaced 3 m apart. Using the IS 875 (Part 2):1987 Table 1 imposed load for rooms of dwelling houses, find the imposed load per metre on an interior beam.

2.0 kN/m² × 3 m tributary width = 6.0 kN/m (characteristic, before load factors).

References

Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.

  • B. J. Goodno, J. M. Gere, Mechanics of Materials, Cengage Learning, 9th edition, 2018.
  • R. C. Hibbeler, Mechanics of Materials, Pearson, 10th edition, 2016.
  • F. P. Beer, E. R. Johnston, J. T. DeWolf, D. F. Mazurek, Mechanics of Materials, McGraw Hill, 8th edition, 2020.
  • E. P. Popov, Engineering Mechanics of Solids, Prentice Hall, 2nd edition, 1998.
Suggest a correction

If something on this page is wrong, tell the editor. Your message is sent privately and is not published.

Sent privately to the Indiacon editor; not published.