8.4 Impact and coefficient of restitution
After this lesson you should be able to:
- Distinguish direct central impact from oblique impact, and elastic, partly elastic and perfectly plastic impacts.
- Define the coefficient of restitution e and combine it with conservation of momentum to find velocities after impact.
- Find the kinetic energy lost in an impact and apply the results to wagon buffers, drop-hammer pile driving and rebound tests.
Theory
An impact is a collision in which large contact forces act for a very short time. Its line of impact is the common normal to the surfaces at the point of contact. If the centres of mass of the two bodies lie on this line and their velocities are along it, the impact is direct and central; if the velocities are at an angle to the line, it is oblique. During the impact each body first deforms (the period of deformation) and then partly recovers (the period of restitution).
Momentum conservation alone is not enough to find two unknown velocities after impact; a second relation is needed that describes how much the bodies spring back. Newton's experimental law of impact supplies it: the relative velocity of separation along the line of impact is e times the relative velocity of approach, v₂′ − v₁′ = e (u₁ − u₂). The coefficient of restitution e lies between 0 and 1. For e = 1 the impact is perfectly elastic and kinetic energy is conserved; for e = 0 it is perfectly plastic and the bodies move off together; real impacts lie between.
Kinetic energy is lost in every impact with e < 1. For a direct central impact the loss is ΔT = ½ [m₁ m₂ / (m₁ + m₂)] (1 − e²) (u₁ − u₂)². The value of e depends on the materials, the impact speed and the shapes in contact, so it is found by test, typically by dropping a body onto a massive surface and measuring the rebound height: e = √(h_rebound / h_drop). The rebound hammer used on concrete is a separate empirical test whose rebound number is not the coefficient e.
In oblique impact between smooth surfaces, the contact force acts only along the line of impact. The velocity components tangent to the surfaces are therefore unchanged, and the normal components obey momentum conservation and the restitution law. In pile driving, the hammer and the pile meet in a direct central impact; the fraction of the hammer's energy that remains as kinetic energy after the blow, (W + e² P)/(W + P) for hammer weight W and pile weight P, is the impact efficiency used in the dynamic pile formulae of foundation engineering. It shows why a heavy hammer with a short drop is more efficient than a light hammer with a long drop.
Derivation
- Direct central impact of masses m₁ and m₂ with velocities u₁ and u₂ before and v₁′ and v₂′ after, all along the line of impact.
- Momentum (no external impulse): m₁ u₁ + m₂ u₂ = m₁ v₁′ + m₂ v₂′.
- Restitution: v₂′ − v₁′ = e (u₁ − u₂).
- Solving the two equations: v₁′ = [m₁ u₁ + m₂ u₂ − e m₂ (u₁ − u₂)] / (m₁ + m₂) and v₂′ = [m₁ u₁ + m₂ u₂ + e m₁ (u₁ − u₂)] / (m₁ + m₂).
- Kinetic energy loss: substituting into ½ m₁ u₁² + ½ m₂ u₂² − ½ m₁ v₁′² − ½ m₂ v₂′² gives ΔT = ½ [m₁ m₂ / (m₁ + m₂)] (1 − e²) (u₁ − u₂)², which is zero only when e = 1.
- Drop test: a body falling from h₁ meets the floor at √(2 g h₁) and leaves at e √(2 g h₁); it rises to h₂ = e² h₁, so e = √(h₂ / h₁).
- Pile driving (u₂ = 0, hammer mass m₁ = W/g, pile mass m₂ = P/g): total kinetic energy after / before = (m₁ + e² m₂) / (m₁ + m₂) = (W + e² P) / (W + P).
Momentum: m₁ u₁ + m₂ u₂ = m₁ v₁′ + m₂ v₂′Restitution: e = (v₂′ − v₁′) / (u₁ − u₂), 0 ≤ e ≤ 1v₁′ = [m₁ u₁ + m₂ u₂ − e m₂ (u₁ − u₂)] / (m₁ + m₂)v₂′ = [m₁ u₁ + m₂ u₂ + e m₁ (u₁ − u₂)] / (m₁ + m₂)Energy loss ΔT = ½ [m₁ m₂ / (m₁ + m₂)] (1 − e²) (u₁ − u₂)² (J)Drop test: e = √(h₂ / h₁)Hammer on pile (pile at rest): efficiency (W + e² P) / (W + P)
- The impact lasts so short a time that external forces (weight, soil resistance) give negligible impulse during it.
- Bodies are smooth, so in oblique impact no tangential impulse acts.
- The coefficient e is taken as a constant for the pair of materials; in reality it falls as impact speed rises.
- Direct central impact formulas ignore rotation; eccentric impacts need rigid-body treatment.
- In the pile example the pile is treated as a rigid body during the blow; the stress-wave behaviour of long piles is outside this lesson.
Codes and standards
Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.
- No design code governs this lesson; impact and restitution are principles of mechanics. Pile driving formulae and the acceptance of driven piles are treated in the foundation engineering subject; impact loads on structures are specified in the bridge, railway and highway subjects.
Worked examples
Problem. A 2 kg sphere moving at 6 m/s to the right meets a 4 kg sphere moving at 3 m/s to the left in direct central impact. The coefficient of restitution is 0.5. Find the velocities after impact and the kinetic energy lost.
- Right positive: u₁ = +6 m/s, u₂ = −3 m/s.
- Momentum: 2 × 6 + 4 × (−3) = 0 = 2 v₁′ + 4 v₂′.
- Restitution: v₂′ − v₁′ = 0.5 × (6 − (−3)) = 4.5 m/s.
- From momentum v₁′ = −2 v₂′, so 3 v₂′ = 4.5: v₂′ = 1.5 m/s (right) and v₁′ = −3 m/s (left).
- Kinetic energy before = 36 + 18 = 54 J; after = 9 + 4.5 = 13.5 J; loss = 40.5 J.
- Formula check: ½ × (2 × 4 / 6) × (1 − 0.25) × 9² = 40.5 J.
Answer. v₁′ = 3 m/s to the left, v₂′ = 1.5 m/s to the right; 40.5 J lost
Problem. A 3 t drop hammer falls freely through 1.5 m onto a pile and helmet of total mass 2 t. Find the velocity after impact and the energy available to drive the pile (a) if the impact is perfectly plastic (e = 0) and (b) if e = 0.5.
- Hammer speed at impact u = √(2 × 9.81 × 1.5) = 5.425 m/s; energy delivered by the fall = 3000 × 9.81 × 1.5 = 44 145 J.
- (a) e = 0: common velocity v = 3000 × 5.425 / 5000 = 3.255 m/s; kinetic energy after = ½ × 5000 × 3.255² = 26 487 J, so the efficiency is 26 487 / 44 145 = 0.60 = W / (W + P).
- (b) e = 0.5: hammer v₁′ = 5.425 × (3000 − 0.5 × 2000) / 5000 = 2.170 m/s; pile v₂′ = 5.425 × 3000 × 1.5 / 5000 = 4.882 m/s.
- Kinetic energy after: hammer ½ × 3000 × 2.170² = 7063 J; pile ½ × 2000 × 4.882² = 23 838 J; total 30 901 J.
- Efficiency = 30 901 / 44 145 = 0.70 = (W + e² P)/(W + P) = (3 + 0.25 × 2)/5. The energy lost in the blow (17.7 kJ or 13.2 kJ) goes into heat and damage at the pile head, which is why helmets and packings are inspected.
Answer. (a) 3.25 m/s, 26.5 kJ (60 %); (b) pile 4.88 m/s, hammer 2.17 m/s, 30.9 kJ (70 %)
Problem. A ball dropped from 2.0 m onto a concrete floor rebounds to 1.28 m. Find the coefficient of restitution and the height of the next rebound.
- e = √(h₂ / h₁) = √(1.28 / 2.0) = √0.64 = 0.8.
- Each rebound height is e² times the previous one: h₃ = 0.64 × 1.28 = 0.8192 m.
- Speeds: arrives at √(2 × 9.81 × 2) = 6.264 m/s, leaves at 0.8 × 6.264 = 5.011 m/s.
Answer. e = 0.8; next rebound 0.819 m
Step-by-step procedure
- Identify the line of impact and choose a positive direction along it; write all velocities with signs.
- For oblique smooth impact, resolve velocities into components along and across the line of impact; the across components are unchanged.
- Write momentum conservation along the line of impact for the system of both bodies.
- Write the restitution equation v₂′ − v₁′ = e (u₁ − u₂) with the same sign convention.
- Solve the two equations, then compute the kinetic energy loss and check that it is not negative.
Site notes
- Wagon buffers and draft gear are designed to absorb the energy lost in coupling; the loss ½ [m₁ m₂ / (m₁ + m₂)] (1 − e²) Δu² grows with the square of the closing speed.
- Drop hammers drive more efficiently when the hammer is heavy relative to the pile; a light hammer dropped from a great height wastes more energy in the blow and is more likely to damage the pile head.
- Cushions and packings in the pile helmet lower e and lengthen the blow, protecting the pile at the cost of some energy; worn or burnt packing changes the driving behaviour and is replaced as part of routine inspection.
- A dropped steel component rebounds from a concrete deck; e for steel on concrete is well below 1, but the rebound can still carry fragments sideways, so exclusion zones allow for bounce.
- Writing the restitution law with velocities in the wrong order, so that e comes out negative.
- Assuming kinetic energy is conserved in an impact that is not perfectly elastic.
- Forgetting that, in oblique smooth impact, the tangential velocity components do not change.
- Taking e = h₂/h₁ instead of √(h₂/h₁) in a drop test.
- Treating the concrete rebound-hammer number as a coefficient of restitution.
The energy left after a plastic blow on a body at rest is m₁/(m₁ + m₂) of the striking energy: a hammer twice the pile mass keeps two-thirds.
Summary
- Momentum plus restitution give the two unknown velocities.
- e = separation speed / approach speed, 0 to 1.
- Loss = ½ [m₁ m₂/(m₁ + m₂)] (1 − e²) (u₁ − u₂)².
- Drop test: e = √(h₂/h₁); hammer efficiency (W + e² P)/(W + P).
Practice questions
Tap a question to see the answer.
1A ball dropped from 4 m rebounds to 1 m. Find e.
e = √(1/4) = 0.5.
2A 20 t wagon at 2 m/s strikes a stationary 30 t wagon; e = 0.6. Find both velocities after impact and the energy lost.
v₁′ = 2 × (20 − 0.6 × 30)/50 = 0.08 m/s; v₂′ = 2 × 20 × 1.6/50 = 1.28 m/s; loss = ½ × 12 000 × 0.64 × 4 = 15 360 J.
3Two equal masses meet in a perfectly elastic direct central impact. What happens to their velocities?
They exchange velocities.
4A 1 t hammer falls 2 m onto a 1.5 t pile; the impact is perfectly plastic. Find the common velocity and the efficiency of the blow.
u = √(2 × 9.81 × 2) = 6.264 m/s; v = 6.264 × 1/2.5 = 2.506 m/s; efficiency = 1/2.5 = 0.40.
5A ball strikes a smooth floor at 10 m/s at 30° to the floor; e = 0.5. Find its rebound speed and angle.
Tangential 8.660 m/s unchanged; normal 5 → 2.5 m/s; speed = √(75 + 6.25) = 9.014 m/s at 16.10° to the floor.
6Why is momentum conserved in an impact while kinetic energy is not?
The contact forces are internal and equal and opposite, so their impulses cancel; but they do unequal work during deformation and recovery, and part of the energy becomes heat, sound and permanent deformation.
References
Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.
- F. P. Beer, E. R. Johnston, D. F. Mazurek, P. J. Cornwell, B. P. Self, Vector Mechanics for Engineers: Statics and Dynamics, McGraw Hill, 12th edition, 2019.
- R. C. Hibbeler, Engineering Mechanics: Statics, Pearson, 15th edition, 2022 (published 2021).
- J. L. Meriam, L. G. Kraige, J. N. Bolton, Engineering Mechanics: Statics, Wiley, 9th edition, 2018.
- S. Timoshenko, D. H. Young, J. V. Rao, S. Pati, Engineering Mechanics (in SI units), McGraw Hill Education (India), 5th edition, 2013.