Indiacon CivilSubscribe

Textbook › Engineering Mechanics › Chapter 9 › Lesson 9.1

9.1 Rotation about a fixed axis

Engineering Mechanics Chapter 9: Plane motion of rigid bodies Under review — not yet three-checked Author: Indiacon

Learning objectives

After this lesson you should be able to:

  • Describe the rotation of a rigid body about a fixed axis by its angular position θ, angular velocity ω and angular acceleration α, with their units.
  • Use the constant-angular-acceleration equations and the relation α = ω dω/dθ for drums, wheels, mixers and slewing cranes.
  • Find the speed and the tangential and normal accelerations of any point of a rotating body, and the speed ratio of belt and gear drives.

Theory

Chapters 7 and 8 treated bodies as particles. Many machines on site, however, are rigid bodies that turn: winch and hoist drums, concrete mixer drums, crusher flywheels, the slewing jib of a tower crane, the cutter head of a tunnel boring machine. The simplest rigid-body motion is rotation about a fixed axis, in which every point of the body moves on a circle centred on that axis, and all the circles lie in parallel planes.

Because the body is rigid, one number fixes its position: the angle θ turned by any line drawn on it, measured in radians from a reference line. Every line in the body turns through the same angle at the same time, so the whole body has a single angular velocity ω = dθ/dt (rad/s) and a single angular acceleration α = dω/dt (rad/s²). Speeds quoted in revolutions per minute are converted with ω = 2π N / 60. When α is constant, the equations have exactly the same form as the constant-acceleration equations of lesson 7.1, with θ, ω and α in place of s, v and a.

O (axis)rPv = r ω, a_t = r αa_n = r ω² (to O)ω, αone ω and one α for the whole bodyIndiacon original, not to scale
Figure 9.1: Rotation about a fixed axis: every point moves on a circle; point P at radius r has speed r ω along the tangent, tangential acceleration r α and normal acceleration r ω² towards the axis. Indiacon original, not to scale.

A point P at distance r from the axis travels an arc s = r θ. Differentiating gives its speed v = r ω, directed along the tangent to its circle, and its tangential acceleration a_t = r α. Since P moves on a circle, it also has a normal (centripetal) acceleration a_n = v²/r = r ω² directed towards the axis, exactly as found for curved paths in lesson 7.3. Points far from the axis therefore move faster and accelerate more, even though the body has one ω and one α.

Where a belt runs on two pulleys without slipping, or two gears mesh, the contact points share the same linear speed, so r₁ ω₁ = r₂ ω₂: the smaller pulley turns faster in the inverse ratio of the radii. A rope wound on a drum moves with the rim, so the rope (and the load it carries) has speed r ω and acceleration r α. These two links between linear and angular motion appear in almost every hoisting and drive problem.

Derivation

  1. Define θ(t) in radians; ω = dθ/dt and α = dω/dt = d²θ/dt².
  2. Chain rule: α = dω/dt = (dω/dθ)(dθ/dt) = ω dω/dθ.
  3. Constant α: integrate dω = α dt from ω₀ to give ω = ω₀ + α t.
  4. Integrate dθ = ω dt = (ω₀ + α t) dt from θ = 0 to give θ = ω₀ t + ½ α t².
  5. Integrate ω dω = α dθ to give ω² = ω₀² + 2 α θ.
  6. Arc length s = r θ with r constant gives v = ds/dt = r ω and a_t = dv/dt = r α.
  7. Normal component of acceleration on a circle (lesson 7.3): a_n = v²/r = r ω²; total acceleration a = √(a_t² + a_n²) = r √(α² + ω⁴).
  8. No slip at a belt or gear contact: v = r₁ ω₁ = r₂ ω₂, so ω₂/ω₁ = r₁/r₂.
Formulas, symbols and SI units
  • ω = dθ/dt (rad/s), α = dω/dt = ω dω/dθ (rad/s²)
  • ω = 2π N / 60 with N in rev/min
  • Constant α: ω = ω₀ + α t; θ = ω₀ t + ½ α t²; ω² = ω₀² + 2 α θ
  • Point at radius r: v = r ω (m/s); a_t = r α; a_n = r ω² = v²/r (m/s²)
  • Total acceleration a = √(a_t² + a_n²)
  • Belt, gear or rope on drum: r₁ ω₁ = r₂ ω₂; rope speed v = r ω, rope acceleration a = r α
Assumptions and limits
  • The body is rigid and the axis is fixed in space (a fixed-axis bearing or pin).
  • Angles are in radians in every formula; revolutions and degrees are converted first.
  • The constant-α equations apply only when α is constant; otherwise integrate α(t), ω(t) or use α = ω dω/dθ.
  • Belts and ropes do not slip or stretch; a slipping belt has a lower driven speed than r₁ ω₁ / r₂.

Codes and standards

Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.

  • No design code governs this lesson; fixed-axis kinematics is a part of mechanics. Speeds, drum diameters and drive ratings for hoists, mixers and cranes are set by the equipment standards and manufacturers' data used in construction-equipment and machine-design work, not by this lesson.

Worked examples

Example 1 (site style)

Problem. A tilting concrete mixer drum starts from rest and reaches its working speed of 18 rev/min uniformly in 6 s. Find the angular acceleration, the number of revolutions made while starting, and, at working speed, the speed and normal acceleration of a blade tip 0.9 m from the axis.

  1. Working speed ω = 2π × 18 / 60 = 1.885 rad/s.
  2. α = (ω − 0) / t = 1.885 / 6 = 0.3142 rad/s².
  3. θ = ½ α t² = ½ × 0.3142 × 36 = 5.655 rad = 5.655 / 2π = 0.90 rev.
  4. Blade tip speed v = r ω = 0.9 × 1.885 = 1.696 m/s; during the start its tangential acceleration was r α = 0.9 × 0.3142 = 0.283 m/s².
  5. Normal acceleration a_n = r ω² = 0.9 × 1.885² = 3.198 m/s², only 0.33 g. Because a_n is well below g, material carried up by the blades falls back near the top and mixes; at a_n = g it would be pinned to the drum wall.

Answer. α = 0.314 rad/s²; 0.90 rev to start; tip 1.70 m/s with a_n = 3.20 m/s²

Example 2 (site style)

Problem. A hoist rope is wound on a drum of radius 0.25 m. The load starts from rest and rises with a constant acceleration of 0.5 m/s². Find the drum's angular acceleration, its angular velocity after 4 s, and how many turns it makes in that time.

  1. The rope moves with the drum rim: α = a / r = 0.5 / 0.25 = 2 rad/s².
  2. After 4 s: ω = α t = 2 × 4 = 8 rad/s = 8 × 60 / 2π = 76.4 rev/min; load speed v = r ω = 2 m/s (check: a t = 0.5 × 4 = 2 m/s).
  3. θ = ½ α t² = ½ × 2 × 16 = 16 rad = 16 / 2π = 2.546 rev.
  4. Rope wound on = r θ = 0.25 × 16 = 4 m, equal to the load rise ½ a t² = ½ × 0.5 × 16 = 4 m.

Answer. α = 2 rad/s²; ω = 8 rad/s (76.4 rev/min); 2.55 turns, 4 m of rope

Example 3 (site style)

Problem. A motor running at 1440 rev/min drives a vibrating screen through a belt. The motor pulley is 100 mm in diameter and the screen pulley 400 mm. Find the screen shaft speed and the belt speed, assuming no slip.

  1. Motor ω₁ = 2π × 1440 / 60 = 150.80 rad/s.
  2. No slip: r₁ ω₁ = r₂ ω₂, so ω₂ = 150.80 × 50 / 200 = 37.70 rad/s, i.e. N₂ = 1440 × 100 / 400 = 360 rev/min.
  3. Belt speed v = r₁ ω₁ = 0.05 × 150.80 = 7.540 m/s (same as 0.2 × 37.70).
  4. With no losses the power is the same on both shafts, so the screen shaft gets four times the motor torque at one quarter of the speed.

Answer. 360 rev/min (37.7 rad/s); belt speed 7.54 m/s

Step-by-step procedure

  1. Fix the axis and choose a positive sense of rotation; convert all speeds to rad/s and all angles to radians.
  2. Decide whether α is constant. If yes, use the three constant-α equations; if not, integrate the given θ(t), ω(t) or α(θ) relation.
  3. For a point at radius r, find v = r ω, a_t = r α and a_n = r ω², and combine them if the total acceleration is needed.
  4. For belts, gears and ropes, link the linear and angular quantities with v = r ω and a = r α at the contact.
  5. Check units and the sense of every answer, and convert back to rev/min or turns where the site uses them.

Site notes

  • Drum mixers are run well below the speed at which a_n = g at the drum wall; beyond it the mix is carried round instead of tumbling.
  • Hoist drum speed sets rope speed: v = r ω. Changing the drum diameter changes both hoisting speed and the torque needed, which is why drum size is fixed by the equipment maker.
  • The tip of a long crane jib moves fast even at a slow slewing speed: at 0.6 rev/min a hook 40 m out travels about 2.5 m/s, so slewing must start and stop gently to limit load swing.
  • Belts slip slightly under load, so the driven pulley runs 1–3 % slower than the ratio r₁/r₂ predicts; checks on site use a tachometer rather than the nominal ratio.
Common mistakes
  • Using rev/min or degrees directly in v = r ω or θ = ½ α t² instead of rad/s and radians.
  • Forgetting the normal acceleration r ω² and reporting only r α as the acceleration of a point.
  • Applying constant-α equations when α changes with time or angle.
  • Inverting the belt ratio: the smaller pulley turns faster, ω₂ = ω₁ r₁ / r₂.
  • Thinking different points of a rigid body have different angular velocities.
Quick check

One revolution per minute is 0.1047 rad/s, so ω in rad/s is roughly N/10; a point at radius r then moves at about r N / 10 m/s.

Summary

  • One θ, one ω and one α describe the whole body.
  • Constant α: ω = ω₀ + α t, θ = ω₀ t + ½ α t², ω² = ω₀² + 2 α θ.
  • A point at radius r: v = r ω, a_t = r α, a_n = r ω².
  • No slip: r₁ ω₁ = r₂ ω₂.

Practice questions

Tap a question to see the answer.

1Convert 300 rev/min to rad/s.

ω = 2π × 300 / 60 = 31.42 rad/s.

2A flywheel running at 120 rev/min is brought to rest uniformly in 20 s. Find the angular deceleration and the turns made while stopping.

α = 12.566 / 20 = 0.6283 rad/s² (deceleration); turns = average speed 60 rev/min × 20/60 min = 20 rev.

3A point on a wheel rim 0.5 m from the axis has ω = 4 rad/s and α = 3 rad/s². Find a_t, a_n and the total acceleration.

a_t = 1.5 m/s²; a_n = 0.5 × 16 = 8 m/s²; a = √(1.5² + 8²) = 8.139 m/s².

4A body turns so that θ = 2t³ − 3t² rad. Find ω and α at t = 2 s.

ω = 6t² − 6t = 12 rad/s; α = 12t − 6 = 18 rad/s².

5A tower crane slews at 0.6 rev/min. Find the speed and the normal acceleration of a hook 40 m from the mast.

ω = 0.06283 rad/s; v = 40 × 0.06283 = 2.513 m/s; a_n = 40 × 0.06283² = 0.158 m/s².

6Why do all points of a rotating drum share one angular velocity but have different speeds?

The body is rigid, so every line in it turns through the same angle in the same time (one ω); speed is r ω, which grows with the distance r from the axis.

References

Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.

  • F. P. Beer, E. R. Johnston, D. F. Mazurek, P. J. Cornwell, B. P. Self, Vector Mechanics for Engineers: Statics and Dynamics, McGraw Hill, 12th edition, 2019.
  • R. C. Hibbeler, Engineering Mechanics: Statics, Pearson, 15th edition, 2022 (published 2021).
  • J. L. Meriam, L. G. Kraige, J. N. Bolton, Engineering Mechanics: Statics, Wiley, 9th edition, 2018.
  • S. Timoshenko, D. H. Young, J. V. Rao, S. Pati, Engineering Mechanics (in SI units), McGraw Hill Education (India), 5th edition, 2013.
Suggest a correction

If something on this page is wrong, tell the editor. Your message is sent privately and is not published.

Sent privately to the Indiacon editor; not published.