Indiacon CivilSubscribe

Textbook › Engineering Mechanics › Chapter 8 › Lesson 8.1

8.1 Newton's second law and D'Alembert's principle

Engineering Mechanics Chapter 8: Kinetics of particles Under review — not yet three-checked Author: Indiacon

Learning objectives

After this lesson you should be able to:

  • State Newton's second law for a particle, F = m a, and apply it in rectangular and in tangential-normal components.
  • Use D'Alembert's principle to turn a dynamics problem into an equivalent equilibrium problem by adding the inertia force −m a.
  • Find cable tensions, contact forces, braking forces and accelerations for lifts, hoists, vehicles on grades and connected bodies.

Theory

Kinematics (Chapter 7) describes motion; kinetics asks what forces cause it. Newton's second law links the two: the resultant force on a particle equals its mass times its acceleration, ΣF = m a. The law is a vector equation, so it holds separately in each direction. Mass is the measure of a body's resistance to a change of velocity and is measured in kilograms; one newton is the force that gives one kilogram an acceleration of one metre per second squared.

The law is valid in an inertial frame of reference, one that is not itself accelerating or rotating. For almost all civil engineering problems the ground is an adequate inertial frame. In rectangular components the law reads ΣF_x = m a_x and ΣF_y = m a_y; on a curved path it is often easier to write ΣF_t = m dv/dt along the path and ΣF_n = m v²/ρ towards the centre of curvature, using the components found in lesson 7.3.

m = 1200 kgTm g−m a (inertia)a (up)T − m g − m a = 0Indiacon original, not to scale
Figure 8.1: Hoist car in dynamic equilibrium: cable tension T, weight m g and the D'Alembert inertia force −m a drawn opposite to the upward acceleration. Indiacon original, not to scale.

Jean le Rond d'Alembert rearranged the law as ΣF + (−m a) = 0. The term −m a is called the inertia force or reversed effective force. It is not a real force exerted by another body; it is a bookkeeping device. Once it is drawn on the free-body diagram, acting opposite to the acceleration, the body can be treated as if it were in equilibrium, and every tool of statics, including moments about any convenient point, can be used. This is called dynamic equilibrium.

Typical site applications are the tension in a hoist or lift cable while the car accelerates, the force on a load sitting on a lift floor, the braking force and deceleration of a vehicle on a downhill grade, and the motion of bodies connected by a rope over a pulley. The method is the same each time: draw the free-body diagram, choose a positive direction along the acceleration, write ΣF = m a (or add −m a and write ΣF = 0), and solve.

Derivation

  1. Newton's second law in its general form states that the resultant force equals the rate of change of linear momentum: ΣF = d(m v)/dt.
  2. For a particle of constant mass, d(m v)/dt = m dv/dt = m a, so ΣF = m a.
  3. Resolve into fixed rectangular axes: ΣF_x = m ẍ, ΣF_y = m ÿ, ΣF_z = m z̈.
  4. Resolve along the path: ΣF_t = m a_t = m dv/dt and ΣF_n = m a_n = m v²/ρ.
  5. D'Alembert's form: move m a to the left side, ΣF − m a = 0. Treating −m a as an extra applied force at the particle gives an equilibrium equation, so ΣF_x + (−m a_x) = 0 and ΣF_y + (−m a_y) = 0, as in statics.
  6. Lift cable: with upward acceleration a, ΣF = T − m g = m a, so T = m (g + a). When the car decelerates while moving up (a negative), T = m (g − |a|).
Formulas, symbols and SI units
  • ΣF = m a (N = kg·m/s²)
  • ΣF_x = m a_x, ΣF_y = m a_y
  • ΣF_t = m dv/dt, ΣF_n = m v²/ρ
  • D'Alembert: ΣF + (−m a) = 0 (inertia force −m a, N)
  • Weight W = m g, g = 9.81 m/s²
  • Lift or hoist cable: T = m (g + a), a positive upwards
  • Block sliding down a slope θ with kinetic friction μ: a = g (sin θ − μ cos θ)
  • Braking on a downhill slope θ: deceleration a = g (μ cos θ − sin θ)
Assumptions and limits
  • The body is a particle of constant mass; rotation is ignored (rigid-body kinetics is Chapter 9).
  • The ground is treated as an inertial frame.
  • Cables and ropes are light and inextensible, and pulleys are light and frictionless, unless stated otherwise.
  • Kinetic friction is taken as μ_k N, constant and opposite to the sliding velocity.
  • The inertia force −m a of D'Alembert's principle is a device for writing equations, not a physical force; it must not be used with forces already measured in an accelerating frame.

Codes and standards

Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.

  • No design code governs this lesson; Newton's second law and D'Alembert's principle are principles of mechanics. Design values such as braking friction for stopping sight distance and dynamic allowances for cranes and lifts are taken from the relevant design subjects, not from this lesson.

Worked examples

Example 1 (site style)

Problem. A construction hoist car and its load have a total mass of 1200 kg. Find the cable tension when the car is at rest, when it accelerates upwards at 1.5 m/s², and when it slows down at 1.5 m/s² while still moving up.

  1. Weight = 1200 × 9.81 = 11 772 N, so at rest T = 11.77 kN.
  2. Accelerating upwards (a = +1.5 m/s²): T − m g = m a, T = 1200 × (9.81 + 1.5) = 13 572 N = 13.57 kN.
  3. D'Alembert check: the inertia force m a = 1800 N acts downwards; equilibrium gives T = 11 772 + 1800 = 13 572 N.
  4. Slowing down while moving up (a = −1.5 m/s²): T = 1200 × (9.81 − 1.5) = 9972 N = 9.97 kN.
  5. The cable sees 15 % more than the static load during the upward start; this is why hoist ropes are checked for the acceleration case, not only the static weight.

Answer. T = 11.77 kN at rest, 13.57 kN accelerating up, 9.97 kN decelerating

Example 2 (exam style)

Problem. A 50 kg block is released from rest on a 30° slope. The coefficient of kinetic friction is 0.2. Find its acceleration and its speed after it has slid 4 m.

  1. Normal to the slope there is no acceleration: N = m g cos 30° = 50 × 9.81 × 0.8660 = 424.8 N.
  2. Along the slope (down positive): m g sin 30° − μ N = m a.
  3. a = g (sin 30° − 0.2 cos 30°) = 9.81 × (0.5 − 0.1732) = 3.206 m/s².
  4. The acceleration is constant, so v² = 2 a s = 2 × 3.206 × 4 = 25.65, v = 5.064 m/s.

Answer. a = 3.21 m/s²; v = 5.06 m/s after 4 m

Example 3 (site style)

Problem. A 20 t loaded truck is travelling at 54 km/h down a 1 in 20 grade (rise over horizontal run, tan θ = 0.05). The tyres can develop a braking friction coefficient of 0.4. Find the maximum deceleration, the braking distance and the braking force, and compare with a level road.

  1. v = 54 / 3.6 = 15 m/s; θ = tan⁻¹ 0.05 = 2.862°, sin θ = 0.04994, cos θ = 0.99875.
  2. Normal reaction N = m g cos θ; friction μ N acts up the slope; the weight component m g sin θ acts down the slope.
  3. Deceleration a = g (μ cos θ − sin θ) = 9.81 × (0.39950 − 0.04994) = 3.429 m/s².
  4. Braking distance s = v² / (2a) = 225 / (2 × 3.429) = 32.81 m.
  5. Braking force = m a + m g sin θ = μ m g cos θ = 0.4 × 20 000 × 9.81 × 0.99875 = 78.38 kN; net decelerating force m a = 68.58 kN.
  6. On a level road a = 0.4 × 9.81 = 3.924 m/s² and s = 225 / 7.848 = 28.67 m; the downgrade adds about 4.1 m (14 %).

Answer. a = 3.43 m/s²; braking distance 32.8 m (28.7 m on level); friction force 78.4 kN

Step-by-step procedure

  1. Isolate the particle and draw its free-body diagram with every real force: weight, normal reactions, friction, cable tensions, applied pushes or pulls.
  2. Choose axes: one along the expected acceleration, one at right angles to it (or tangential and normal axes on a curve).
  3. Write ΣF = m a along the acceleration and ΣF = 0 (or ΣF_n = m v²/ρ) across it. Alternatively add the inertia force −m a and write equilibrium equations.
  4. For connected bodies, write one equation for each body and use the rope or contact condition to link their accelerations.
  5. Solve, then check the sign of every answer and whether friction or cable assumptions (taut rope, sliding) still hold.

Site notes

  • Hoist and lift cables carry the largest tension while the car starts upwards or stops while moving down; the acceleration term m a is added to the weight in both cases.
  • A load resting on a lift floor or on a crane hook feels lighter during downward acceleration; if the downward acceleration reached g the contact force would fall to zero and loose items could lift off the platform.
  • On long downhill grades the gravity component m g sin θ acts with the vehicle, so braking distances are longer and brakes run hotter; this is the mechanics behind lower speed limits and escape ramps on ghat roads.
  • When a crane lifts a load off the ground suddenly, the rope tension briefly exceeds the static weight; smooth slow starts keep the inertia term small.
Common mistakes
  • Writing T = m g for a cable when the load is accelerating.
  • Drawing the D'Alembert inertia force in the direction of the acceleration instead of opposite to it.
  • Adding the inertia force and also writing ΣF = m a, which counts the acceleration twice.
  • Using μ m g for friction on a slope instead of μ m g cos θ.
  • Taking the rope tension as equal to the hanging weight in a connected system that is accelerating.
Quick check

For a body hanging from a cable, T/(m g) = 1 + a/g: an upward acceleration of 1 m/s² adds about 10 % to the static tension.

Summary

  • ΣF = m a, written component by component in an inertial frame.
  • D'Alembert: add −m a and solve as equilibrium.
  • Lift cable: T = m (g + a).
  • Slopes: a = g (sin θ − μ cos θ) sliding down; braking downhill a = g (μ cos θ − sin θ).

Practice questions

Tap a question to see the answer.

1A 2 t load is hoisted with an upward acceleration of 0.5 m/s². Find the rope tension.

T = 2000 × (9.81 + 0.5) = 20 620 N = 20.62 kN.

2A 10 kg box rests on the floor of a lift that accelerates downwards at 2 m/s². Find the floor reaction.

N = 10 × (9.81 − 2) = 78.1 N.

3A 1500 kg car brakes uniformly from 20 m/s to rest in 40 m on a level road. Find the braking force.

a = 20² / (2 × 40) = 5 m/s²; F = 1500 × 5 = 7500 N.

4A 30 kg mass hangs from a rope passing over a light frictionless pulley to a 20 kg block on a smooth horizontal table. Find the acceleration and the rope tension.

a = 30 × 9.81 / 50 = 5.886 m/s²; T = 20 × 5.886 = 117.7 N.

5A locomotive exerts a drawbar pull of 60 kN on a 40 t rake of wagons against a total resistance of 20 kN on level track. Find the acceleration.

a = (60 000 − 20 000) / 40 000 = 1.0 m/s².

6Is D'Alembert's inertia force a real force?

No. It is −m a added to the free-body diagram so that the dynamics equation can be written as equilibrium; no body exerts it.

References

Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.

  • F. P. Beer, E. R. Johnston, D. F. Mazurek, P. J. Cornwell, B. P. Self, Vector Mechanics for Engineers: Statics and Dynamics, McGraw Hill, 12th edition, 2019.
  • R. C. Hibbeler, Engineering Mechanics: Statics, Pearson, 15th edition, 2022 (published 2021).
  • J. L. Meriam, L. G. Kraige, J. N. Bolton, Engineering Mechanics: Statics, Wiley, 9th edition, 2018.
  • S. Timoshenko, D. H. Young, J. V. Rao, S. Pati, Engineering Mechanics (in SI units), McGraw Hill Education (India), 5th edition, 2013.
Suggest a correction

If something on this page is wrong, tell the editor. Your message is sent privately and is not published.

Sent privately to the Indiacon editor; not published.