Indiacon CivilSubscribe

Textbook › Engineering Mechanics › Chapter 8 › Lesson 8.3

8.3 Impulse and momentum

Engineering Mechanics Chapter 8: Kinetics of particles Under review — not yet three-checked Author: Indiacon

Learning objectives

After this lesson you should be able to:

  • Define linear momentum and the impulse of a force, with their units, and read impulse as the area under a force-time graph.
  • Derive the impulse-momentum principle from Newton's second law and use it to find average forces in short events such as hammer blows, braking and jets.
  • Apply conservation of linear momentum to systems of particles, such as coupling railway wagons, and find the kinetic energy lost.

Theory

Newton's second law in its original form says that force equals the rate of change of momentum, ΣF = d(m v)/dt. Linear momentum, L = m v, is a vector with the direction of the velocity and the unit kg·m/s, which is the same as N·s. Multiplying the law by dt and integrating over an interval of time gives the impulse-momentum principle: the impulse of the resultant force equals the change in momentum, ∫ ΣF dt = m v₂ − m v₁.

The impulse of a force is ∫ F dt over the time it acts. For a constant force it is simply F Δt; for a varying force it is the area under the force-time graph. The method is most useful when forces act for a short time and are hard to measure, as in a hammer blow, a vehicle hitting a barrier, or a jet of water striking a plate. The impulse-momentum principle then gives the average force, F_avg = m Δv / Δt, without knowing how the force varied during contact.

tFF_avgarea = impulsepeak∫ F dt = m v₂ − m v₁Indiacon original, not to scale
Figure 8.3: Force-time graph of an impact: the shaded area is the impulse, and the dashed line is the average force that gives the same area over the contact time. Indiacon original, not to scale.

Impulse-momentum is a vector relation, so it is applied component by component. It is the natural method when time is given or wanted, just as the work-energy principle of lesson 8.2 is the natural method when distance is given or wanted. Many problems can be solved either way, and solving them both ways is a good check.

When two or more particles interact, the forces between them are equal and opposite (Newton's third law) and act for the same time, so their impulses cancel. If no external impulse acts on the system in some direction, the total momentum in that direction is conserved: Σ m v before = Σ m v after. Railway wagons coupling in a yard, a pile hammer striking a pile and a trolley from which a load is pushed off are all handled this way. Momentum is conserved in such events even though kinetic energy usually is not; the energy lost goes into deformation, heat and sound.

Derivation

  1. Start from ΣF = d(m v)/dt for a particle.
  2. Multiply by dt: ΣF dt = d(m v).
  3. Integrate from t₁ to t₂: ∫ ΣF dt = m v₂ − m v₁. The left side is the impulse of the resultant force.
  4. For a constant force: ΣF (t₂ − t₁) = m (v₂ − v₁). For a varying force, the average force over Δt is F_avg = m (v₂ − v₁) / Δt.
  5. For two particles A and B, the impulses of the internal forces are equal and opposite. Adding the two impulse-momentum equations, the internal terms cancel: Σ(external impulse) = Σ m v₂ − Σ m v₁.
  6. If the external impulse is zero (or negligible during a short event), m_A v_A1 + m_B v_B1 = m_A v_A2 + m_B v_B2: conservation of linear momentum.
  7. For a steady jet of density ρ, area A and speed v striking a fixed flat plate normally and leaving along it, the mass flow per second is ρ A v and its normal momentum is destroyed, so F = ρ A v².
Formulas, symbols and SI units
  • Linear momentum L = m v (kg·m/s = N·s)
  • Impulse I = ∫ F dt; constant force I = F Δt (N·s)
  • Impulse-momentum: ∫ ΣF dt = m v₂ − m v₁
  • Average force F_avg = m (v₂ − v₁) / Δt (N)
  • Conservation of momentum: Σ m v (before) = Σ m v (after) when external impulse is zero
  • Perfectly plastic coupling: v = (m₁ v₁ + m₂ v₂) / (m₁ + m₂)
  • Jet on a fixed normal plate: F = ρ A v² (N)
Assumptions and limits
  • Bodies are particles; rotation and angular momentum are not considered (Chapter 9).
  • In short impacts, ordinary forces such as weight and rolling resistance give negligible impulse compared with the contact force, so they are ignored during the event only.
  • Average forces from F_avg = m Δv / Δt depend on the contact time; peak forces are higher than the average.
  • The jet result assumes a steady jet, a fixed plate and no splash back.

Codes and standards

Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.

  • No design code governs this lesson; impulse and momentum are principles of mechanics. Design impact loads on bridges, barriers and buffer stops are specified in the bridge, highway and railway subjects, not derived here.

Worked examples

Example 1 (site style)

Problem. A 2 kg club hammer moving at 6 m/s strikes the head of a chisel and stops without rebounding in 0.004 s. Find the impulse and the average force on the chisel.

  1. Momentum before = 2 × 6 = 12 kg·m/s; after = 0.
  2. Impulse on the hammer = 0 − 12 = −12 N·s; the chisel receives +12 N·s.
  3. Average force = 12 / 0.004 = 3000 N = 3 kN.
  4. The hammer weight (19.6 N) over 0.004 s gives only 0.08 N·s and is rightly neglected. A short contact time is what turns a modest momentum into a large force.

Answer. Impulse 12 N·s; average force 3 kN

Example 2 (site style)

Problem. A 15 t dumper travelling at 36 km/h on a level haul road is braked to rest in 5 s by a constant braking force. Find the force and the stopping distance.

  1. v₁ = 36 / 3.6 = 10 m/s; v₂ = 0; Δt = 5 s.
  2. Impulse-momentum: −F × 5 = 15 000 × (0 − 10), so F = 30 000 N = 30 kN.
  3. Deceleration = F / m = 2 m/s²; distance = ½ × (10 + 0) × 5 = 25 m.
  4. Work-energy check: F s = 30 000 × 25 = 750 kJ = ½ × 15 000 × 10², agreeing exactly.

Answer. F = 30 kN; stopping distance 25 m

Example 3 (exam style)

Problem. In a railway yard a 30 t wagon moving at 2 m/s runs into a stationary 20 t wagon and the two couple. Find their common velocity and the kinetic energy lost.

  1. No external horizontal impulse acts during the short coupling, so momentum is conserved.
  2. 30 000 × 2 + 20 000 × 0 = 50 000 v, v = 60 000 / 50 000 = 1.2 m/s.
  3. Kinetic energy before = ½ × 30 000 × 2² = 60 000 J.
  4. Kinetic energy after = ½ × 50 000 × 1.2² = 36 000 J.
  5. Loss = 24 000 J = 24 kJ, 40 % of the initial energy, absorbed by the couplers, buffers and draft gear.

Answer. v = 1.2 m/s; 24 kJ (40 %) lost

Step-by-step procedure

  1. Choose the system: one particle, or several bodies whose internal forces will cancel.
  2. Choose a positive direction (or x and y axes) and write the momentum m v of each body before and after with signs.
  3. List the external forces and the time each acts; compute their impulses (area under F-t if they vary).
  4. Write external impulse = momentum after − momentum before, in each direction; set the impulse to zero if it is negligible during a short event.
  5. Solve, then check kinetic energy: it may not increase in an impact without an energy source.

Site notes

  • Contact time controls force: rubber fenders, sand drums and crash cushions lengthen the stopping time so that the same momentum change produces a smaller average force.
  • Wagons in a yard are coupled at walking speed because the energy absorbed by the draft gear grows with the square of the closing speed while momentum grows only linearly.
  • Water jets from monitors, nozzles and spillway flips exert large forces, ρ A v²; a 20 m/s jet from a 2000 mm² nozzle pushes a plate with about 800 N, enough to dislodge loose blocks.
  • Momentum is conserved in a pile hammer blow, so a heavier hammer at lower drop height drives better than a light hammer dropped from high: the same energy is transferred to the pile with less wasted in the impact (lesson 8.4).
Common mistakes
  • Forgetting that momentum and impulse are vectors and dropping the sign of a velocity that reverses.
  • Assuming kinetic energy is conserved whenever momentum is conserved.
  • Using the peak force when only the average force can be found from impulse-momentum.
  • Including internal forces between bodies of the chosen system as external impulses.
  • Neglecting a large external force, such as the braking force of a locomotive, during an event that lasts several seconds.
Quick check

Halving the contact time doubles the average force for the same change of momentum; to soften an impact, make it last longer.

Summary

  • Momentum L = m v; impulse I = ∫ F dt, both in N·s.
  • ∫ ΣF dt = m v₂ − m v₁, component by component.
  • No external impulse: total momentum conserved, energy usually not.
  • Jet on a normal plate: F = ρ A v².

Practice questions

Tap a question to see the answer.

1Find the impulse of a constant 500 N force acting for 0.2 s.

I = 500 × 0.2 = 100 N·s.

2A 1500 kg car accelerates from rest to 20 m/s in 8 s. Find the average net forward force.

F = 1500 × 20 / 8 = 3750 N.

3A water jet of area 0.002 m² and speed 20 m/s strikes a fixed flat plate normally. Find the force on the plate (ρ = 1000 kg/m³).

F = 1000 × 0.002 × 20² = 800 N.

4A 100 kg crate is pushed horizontally off the back of a 400 kg trolley standing at rest on smooth level rails; the crate leaves at 2 m/s relative to the ground. Find the trolley's velocity.

0 = 100 × (−2) + 400 v, v = 0.5 m/s forwards.

5A 40 t wagon moving at 1.5 m/s catches and couples with a 20 t wagon moving at 0.5 m/s in the same direction. Find the common velocity.

v = (40 × 1.5 + 20 × 0.5) / 60 = 70 / 60 = 1.167 m/s.

6A force rises linearly from 0 to 6 kN and falls linearly back to 0 in a total of 0.05 s. Find the impulse and the speed it gives a 50 kg body starting from rest.

I = ½ × 6000 × 0.05 = 150 N·s; v = 150 / 50 = 3 m/s.

References

Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.

  • F. P. Beer, E. R. Johnston, D. F. Mazurek, P. J. Cornwell, B. P. Self, Vector Mechanics for Engineers: Statics and Dynamics, McGraw Hill, 12th edition, 2019.
  • R. C. Hibbeler, Engineering Mechanics: Statics, Pearson, 15th edition, 2022 (published 2021).
  • J. L. Meriam, L. G. Kraige, J. N. Bolton, Engineering Mechanics: Statics, Wiley, 9th edition, 2018.
  • S. Timoshenko, D. H. Young, J. V. Rao, S. Pati, Engineering Mechanics (in SI units), McGraw Hill Education (India), 5th edition, 2013.
Suggest a correction

If something on this page is wrong, tell the editor. Your message is sent privately and is not published.

Sent privately to the Indiacon editor; not published.