8.2 Work-energy principle
After this lesson you should be able to:
- Define the work of a force and the kinetic energy of a particle, with their units.
- Derive the work-energy principle U(1→2) = T₂ − T₁ from Newton's second law and use it to find speeds and distances without finding the acceleration.
- Use gravitational and spring potential energy, conservation of energy and power for hoists, braking vehicles and buffer stops.
Theory
Newton's second law gives the acceleration, and the acceleration must then be integrated to find speed or distance. When a problem asks only for speed at a position, or the distance needed to stop, it is quicker to integrate the law once and for all. The result is the work-energy principle: the total work done on a particle by all forces between two positions equals the change in its kinetic energy, U(1→2) = T₂ − T₁, with T = ½ m v².
Work was defined in lesson 6.1: a force F moving its point of application through a displacement dr does work dU = F · dr. Only the component of force along the motion works. A normal reaction on a fixed surface does no work, because it is perpendicular to the motion; kinetic friction does negative work, μ N times the sliding distance; the weight does work m g h when the particle descends a height h, regardless of the path. Work and energy are scalars measured in joules (1 J = 1 N·m).
Some forces, such as weight and the force of an elastic spring, are conservative: their work depends only on the end positions. Their work can be written as a loss of potential energy, V_g = m g h for gravity and V_e = ½ k x² for a linear spring with stiffness k and extension or compression x. If only conservative forces do work, T + V stays constant: this is conservation of mechanical energy. Friction is non-conservative; the mechanical energy it removes becomes heat in brake drums, tyres or sliding surfaces.
Power is the rate of doing work, P = dU/dt = F · v, measured in watts (1 W = 1 J/s). Hoist motors, pumps and winches are rated by power, and the input power is the output power divided by the efficiency. Civil uses of the energy method include the stopping distance of a vehicle on a grade, the compression of a buffer stop or a fender when a wagon or vessel strikes it, and the motor size needed to lift a load at a given speed.
Derivation
- Start from the tangential component of Newton's second law: ΣF_t = m a_t = m dv/dt.
- Use the chain rule: dv/dt = (dv/ds)(ds/dt) = v dv/ds, so ΣF_t ds = m v dv.
- Integrate from position 1 (speed v₁) to position 2 (speed v₂): ∫ ΣF_t ds = ∫ m v dv = ½ m v₂² − ½ m v₁².
- The left side is the total work U(1→2) of all forces, because only the tangential component does work. Hence U(1→2) = T₂ − T₁.
- Gravity: with y measured upwards, the work of W = m g between y₁ and y₂ is −m g (y₂ − y₁) = V_g1 − V_g2 with V_g = m g y.
- Linear spring: F = k x opposes the deformation, so its work from x₁ to x₂ is −∫ k x dx = ½ k x₁² − ½ k x₂² = V_e1 − V_e2 with V_e = ½ k x².
- If all working forces are conservative, T₂ − T₁ = V₁ − V₂, so T₁ + V₁ = T₂ + V₂.
Work of a force: U = ∫ F · dr; constant force along the motion U = F s cos α (J)Kinetic energy T = ½ m v² (J)Work-energy principle: U(1→2) = T₂ − T₁Gravitational potential energy V_g = m g h (J)Spring potential energy V_e = ½ k x² (J), k in N/mConservation: T₁ + V₁ = T₂ + V₂ (conservative forces only)Power P = F v (W); efficiency η = output power / input powerStopping distance on a grade (downhill, from speed v): s = v² / [2 g (μ cos θ − sin θ)]
- The body is a particle; rotational kinetic energy is ignored (it is added in Chapter 9).
- Springs are linear and massless; buffers that are not linear need their measured force-deflection curve instead of ½ k x².
- Kinetic friction is constant at μ_k N over the sliding distance.
- g = 9.81 m/s² and is constant over the heights involved.
- The energy method gives speeds and distances, not times or directions; use Newton's law or impulse-momentum for those.
Codes and standards
Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.
- No design code governs this lesson; the work-energy principle is a principle of mechanics. Braking-friction values for road design and the energy capacity required of buffer stops and fenders come from the highway, railway and port design subjects, not from this lesson.
Worked examples
Problem. A 10 kg block slides 5 m down a 30° slope from rest. The coefficient of kinetic friction is 0.25. Use the work-energy principle to find its speed at the bottom.
- Work of gravity = m g × (vertical drop) = 10 × 9.81 × 5 sin 30° = 245.25 J.
- Normal reaction N = m g cos 30° = 84.96 N; it does no work.
- Work of friction = −μ N s = −0.25 × 84.96 × 5 = −106.20 J.
- U(1→2) = 245.25 − 106.20 = 139.05 J = ½ × 10 × v² − 0.
- v = √(2 × 139.05 / 10) = 5.274 m/s. Check with Newton's law: a = 9.81 (0.5 − 0.2165) = 2.781 m/s², v² = 2 × 2.781 × 5 = 27.81, v = 5.274 m/s.
Answer. v = 5.27 m/s
Problem. A 1200 kg car travelling at 72 km/h brakes on a downhill stretch where the road drops 1 m for every 25 m travelled along it (sin θ = 0.04). The braking friction coefficient is 0.35. Find the braking distance and compare with a level road.
- v = 20 m/s; initial kinetic energy T₁ = ½ × 1200 × 20² = 240 000 J.
- cos θ = √(1 − 0.04²) = 0.9992.
- Over a braking distance s: work of gravity = + m g s sin θ; work of friction = − μ m g cos θ s.
- 0 − 240 000 = m g s (sin θ − μ cos θ), so s = v² / [2 g (μ cos θ − sin θ)] = 400 / [2 × 9.81 × (0.34972 − 0.04)] = 65.83 m.
- On a level road s = 400 / (2 × 9.81 × 0.35) = 58.25 m. The 4 % downgrade adds about 7.6 m, and the car's mass cancels out of the answer.
Answer. s = 65.8 m downhill against 58.2 m on the level
Problem. A 20 t wagon rolls at 1.0 m/s into a spring buffer stop of total stiffness 2 MN/m. Neglecting friction, find the maximum buffer compression and the peak buffer force.
- Kinetic energy T₁ = ½ × 20 000 × 1.0² = 10 000 J = 10 kJ.
- At maximum compression the wagon is momentarily at rest: T₂ = 0, and the energy is stored in the spring, ½ k x².
- ½ × 2 × 10⁶ × x² = 10 000, so x² = 0.01 and x = 0.10 m = 100 mm.
- Peak force F = k x = 2 × 10⁶ × 0.10 = 200 kN, about the weight of the wagon (196 kN).
- Doubling the speed quadruples the energy to 40 kJ and doubles x and F, so buffer stops are sized for the highest likely impact speed.
Answer. x = 100 mm; peak force 200 kN
Step-by-step procedure
- Pick the two positions 1 and 2 at which speeds are known or wanted.
- Draw a free-body diagram and list every force that does work between them; mark those that do none (normal reactions on fixed surfaces, forces at fixed points).
- Compute the work of each force: constant forces as F s cos α, weight as ± m g h, springs as ½ k (x₁² − x₂²), friction as −μ N s.
- Write U(1→2) = ½ m v₂² − ½ m v₁² (or T₁ + V₁ = T₂ + V₂ if friction is absent) and solve.
- For power, use P = F v at the instant required and divide by the efficiency to get the input power.
Site notes
- Braking distance grows with the square of the speed and is longer on downgrades; the energy form s = v² / [2 g (μ cos θ − sin θ)] shows both effects at once and does not need the vehicle mass.
- Buffer stops, fenders and crash cushions are energy absorbers; they are chosen by the energy ½ m v² they must take, and the peak force then follows from their stiffness or force-deflection curve.
- A hoist lifting at constant speed needs power m g v at the drum; a 2 t load at 0.5 m/s needs about 9.8 kW plus losses, which sets the motor rating.
- Brakes turn kinetic and potential energy into heat; on long descents this heat, not the friction coefficient, is what causes brake fade, which is why heavy vehicles use low gears on ghat roads.
- Including the normal reaction as a working force on a fixed surface.
- Counting the weight both as work and as a change of potential energy.
- Using ½ k x² for the work of a spring between two non-zero deformations instead of ½ k (x₁² − x₂²).
- Forgetting the sign of the work of friction, which is always negative for the sliding body.
- Trying to get a time from the energy equation; work-energy gives speeds and distances only.
Kinetic energy grows with v²: a 20 % increase in speed means 44 % more energy to absorb and about 44 % more braking distance.
Summary
- U(1→2) = T₂ − T₁ with T = ½ m v².
- Weight and springs are conservative: V_g = m g h, V_e = ½ k x².
- Friction removes energy: work = −μ N s.
- Power P = F v; input = output / efficiency.
Practice questions
Tap a question to see the answer.
1A hoist lifts 500 kg through 20 m at constant speed in 40 s. Find the work done and the output power.
U = 500 × 9.81 × 20 = 98 100 J; P = 98 100 / 40 = 2452.5 W (2.45 kW).
2A 2 kg bolt is dropped from 10 m. Find its speed on reaching the ground by the energy method.
v = √(2 × 9.81 × 10) = 14.01 m/s.
3A spring of stiffness 50 kN/m is compressed by 40 mm. Find the work done. How much more work is needed to compress it from 40 mm to 80 mm?
½ × 50 000 × 0.04² = 40 J; ½ × 50 000 × (0.08² − 0.04²) = 120 J.
4A 1000 kg car moving at 25 m/s is stopped on a level road by a constant braking force of 5 kN. Find the stopping distance.
s = ½ × 1000 × 25² / 5000 = 312 500 / 5000 = 62.5 m.
5A crane hoists 2 t at a steady 0.5 m/s. Find the output power and the motor input power if the drive efficiency is 80 %.
P = 2000 × 9.81 × 0.5 = 9810 W; input = 9810 / 0.8 = 12 262.5 W (12.26 kW).
6Why does the normal reaction of a fixed floor do no work on a block sliding across it?
It is perpendicular to the displacement, so F · dr = 0.
References
Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.
- F. P. Beer, E. R. Johnston, D. F. Mazurek, P. J. Cornwell, B. P. Self, Vector Mechanics for Engineers: Statics and Dynamics, McGraw Hill, 12th edition, 2019.
- R. C. Hibbeler, Engineering Mechanics: Statics, Pearson, 15th edition, 2022 (published 2021).
- J. L. Meriam, L. G. Kraige, J. N. Bolton, Engineering Mechanics: Statics, Wiley, 9th edition, 2018.
- S. Timoshenko, D. H. Young, J. V. Rao, S. Pati, Engineering Mechanics (in SI units), McGraw Hill Education (India), 5th edition, 2013.