7.3 Normal and tangential components
After this lesson you should be able to:
- Resolve the velocity and acceleration of a particle on a curved path into tangential and normal components.
- Derive a_t = dv/dt and a_n = v²/ρ, and find the radius of curvature ρ of a path y = f(x).
- Apply the results to vehicles on horizontal curves and derive the mechanics behind superelevation.
Theory
Rectangular components are convenient when the axes match the motion, but for a vehicle on a road curve or a train on a railway curve it is more natural to use axes that travel with the particle: one along the path (tangential, unit vector e_t) and one towards the centre of curvature (normal, unit vector e_n). In these path coordinates the velocity has only one component, v = v e_t, because the velocity is always tangent to the path.
The acceleration has two components. The tangential component a_t = dv/dt measures the change of speed: it is positive when the particle speeds up and negative when it brakes. The normal component a_n = v²/ρ, where ρ is the radius of curvature of the path at that point, measures the change of direction. It always points towards the centre of curvature and is never negative. A vehicle going round a curve at constant speed therefore still accelerates: a_t = 0 but a_n = v²/ρ.
The total acceleration is a = a_t e_t + a_n e_n, with magnitude √(a_t² + a_n²). For a circular path ρ is the radius of the circle. For a path y = f(x), the radius of curvature is ρ = [1 + (dy/dx)²]^(3/2) / |d²y/dx²|. A straight line has ρ infinite and a_n = 0.
The normal acceleration must be produced by a force towards the centre. For a road vehicle this comes from tyre friction and from tilting the road, called superelevation. Resolving forces for a vehicle on a road banked at angle θ, with side friction coefficient f, gives (tan θ + f)/(1 − f tan θ) = v²/(gR); for the small angles and friction used on roads this is close to e + f = v²/(gR), where e = tan θ. With V in km/h, v²/(gR) = V²/(127 R). Highway and railway design codes build on this relation; they are treated in the highway and railway subjects.
Derivation
- Write v = v e_t. Differentiating: a = (dv/dt) e_t + v (de_t/dt).
- As the particle moves a distance ds along the path, e_t turns through dθ = ds/ρ, and de_t has magnitude dθ and direction e_n. So de_t/dt = (dθ/dt) e_n = (1/ρ)(ds/dt) e_n = (v/ρ) e_n.
- Hence a = (dv/dt) e_t + (v²/ρ) e_n: a_t = dv/dt = v dv/ds, a_n = v²/ρ.
- For y = f(x), the curvature 1/ρ = |y″| / (1 + y′²)^(3/2), from the rate of turning of the tangent angle tan⁻¹ y′ with arc length ds = √(1 + y′²) dx.
- Banked curve: weight W = m g, normal reaction N, friction F = f N down the slope. Resolving horizontally and vertically: N sin θ + f N cos θ = m v²/R and N cos θ − f N sin θ = m g. Dividing gives (tan θ + f)/(1 − f tan θ) = v²/(gR), and dropping the small product f tan θ gives e + f ≈ v²/(gR).
v = v e_t (m/s)a_t = dv/dt = v dv/ds (m/s²)a_n = v²/ρ (m/s², towards the centre of curvature)|a| = √(a_t² + a_n²)ρ = [1 + (dy/dx)²]^(3/2) / |d²y/dx²| (m)Banked curve: (tan θ + f)/(1 − f tan θ) = v²/(gR); approximately e + f = v²/(gR) = V²/(127 R), V in km/h, R in m
- The particle model is used: the vehicle's size and the difference between inner and outer wheels are ignored.
- In the banked-curve result, friction is taken at its full available value f and the product f tan θ is neglected as small.
- The path is smooth, so ρ is defined at every point.
- g = 9.81 m/s².
Codes and standards
Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.
- No design code governs this lesson; path coordinates are a principle of mechanics. The superelevation and side-friction values used in road and railway design come from the design codes discussed in the highway and railway subjects, not from this lesson.
Worked examples
Problem. A car travels round a horizontal curve of radius 200 m at 72 km/h. Find its normal acceleration. If the driver now brakes at 1.5 m/s² while on the curve, find the total acceleration.
- v = 72 / 3.6 = 20 m/s.
- a_n = v²/ρ = 400 / 200 = 2.0 m/s², towards the centre.
- Braking gives a_t = −1.5 m/s².
- |a| = √(2.0² + 1.5²) = 2.5 m/s². Braking on a curve adds to the demand on tyre friction.
Answer. a_n = 2.0 m/s²; total 2.5 m/s²
Problem. A particle moves along the path y = 0.01 x² (metres). Find the radius of curvature at x = 50 m. If the speed there is 10 m/s and constant, find the acceleration.
- y′ = 0.02 x = 1 at x = 50 m; y″ = 0.02.
- ρ = (1 + 1²)^(3/2) / 0.02 = 2.828 / 0.02 = 141.42 m.
- a_t = 0 (constant speed); a_n = 10² / 141.42 = 0.7071 m/s².
Answer. ρ = 141.4 m; a = 0.707 m/s² towards the centre of curvature
Problem. A train runs round a curve of radius 600 m at 90 km/h and is speeding up at 0.4 m/s². Find the components and magnitude of its acceleration, and the value of e + f that would be needed on an equivalent road curve.
- v = 90 / 3.6 = 25 m/s.
- a_n = 25² / 600 = 1.042 m/s²; a_t = 0.4 m/s².
- |a| = √(1.042² + 0.4²) = 1.116 m/s².
- v²/(gR) = 625 / (9.81 × 600) = 0.1062, the same as V²/(127 R) = 8 100 / 76 200 = 0.1063 to rounding.
Answer. a_t = 0.40 m/s², a_n = 1.04 m/s², |a| = 1.12 m/s²; e + f ≈ 0.106
Step-by-step procedure
- Identify the path and the point of interest; find ρ there (the radius for a circle, the curvature formula for y = f(x)).
- Convert the speed to m/s.
- Find a_t from the change of speed (dv/dt or v dv/ds) and a_n = v²/ρ.
- Combine: |a| = √(a_t² + a_n²); a_n always points towards the centre of curvature.
- For a vehicle, compare v²/(gR) with the available e + f to judge whether the curve can be taken safely.
Site notes
- Normal acceleration grows with the square of speed: a vehicle at 100 km/h on a curve needs about twice the sideways grip it needs at 70 km/h. Speed limits on sharp curves follow directly from a_n = v²/R.
- Braking or accelerating on a curve adds a tangential component to the normal one; the tyre must supply both, so skids on curves often start when a driver brakes hard mid-curve.
- Railways provide cant (raising the outer rail) for the same reason that roads have superelevation: to let part of v²/R come from the tilt of the support instead of from wheel flanges or friction.
- Assuming zero acceleration when the speed is constant on a curve.
- Using the distance from the origin instead of the radius of curvature ρ in v²/ρ.
- Forgetting the 3/2 power in the curvature formula, or using y″ alone as the curvature when the slope is not small.
- Using V in km/h with g in m/s² in v²/(gR) without the 3.6 conversion (the 127 already contains it).
- Adding a_t and a_n arithmetically instead of as perpendicular components.
a_t changes the speed and a_n = v²/ρ changes the direction; on any curve, a_n is never zero unless the particle is at rest.
Summary
- v = v e_t; a = (dv/dt) e_t + (v²/ρ) e_n.
- a_n points to the centre of curvature and needs a real force to produce it.
- ρ = (1 + y′²)^(3/2) / |y″| for a path y = f(x).
- Banked curve: e + f ≈ v²/(gR) = V²/(127R).
Practice questions
Tap a question to see the answer.
1A vehicle travels at 15 m/s on a curve of radius 75 m. Find its normal acceleration.
a_n = 225 / 75 = 3 m/s².
2A particle moves on a circle of radius 2 m with path distance s = t³ (m, s). Find its total acceleration at t = 1 s.
v = 3t² = 3 m/s; a_t = 6t = 6 m/s²; a_n = 9/2 = 4.5 m/s²; |a| = 7.5 m/s².
3Find the radius of curvature of y = x³/3 at x = 1 m.
y′ = 1, y″ = 2; ρ = 2^(3/2) / 2 = 1.414 m.
4A car moves at 60 km/h on a curve of radius 150 m. Find a_n.
v = 16.67 m/s; a_n = 277.8 / 150 = 1.852 m/s².
5Find e + f needed for 80 km/h on a curve of radius 250 m.
v²/(gR) = 22.22² / (9.81 × 250) = 0.2014 (V²/127R = 0.2016).
6Why does a particle moving at constant speed on a circle accelerate?
Its direction changes continuously, so the velocity vector changes; the change is a_n = v²/R towards the centre.
References
Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.
- F. P. Beer, E. R. Johnston, D. F. Mazurek, P. J. Cornwell, B. P. Self, Vector Mechanics for Engineers: Statics and Dynamics, McGraw Hill, 12th edition, 2019.
- R. C. Hibbeler, Engineering Mechanics: Statics, Pearson, 15th edition, 2022 (published 2021).
- J. L. Meriam, L. G. Kraige, J. N. Bolton, Engineering Mechanics: Statics, Wiley, 9th edition, 2018.
- S. Timoshenko, D. H. Young, J. V. Rao, S. Pati, Engineering Mechanics (in SI units), McGraw Hill Education (India), 5th edition, 2013.