Indiacon CivilSubscribe

Textbook › Engineering Mechanics › Chapter 7 › Lesson 7.4

7.4 Projectile motion

Engineering Mechanics Chapter 7: Kinematics of particles Under review — not yet three-checked Author: Indiacon

Learning objectives

After this lesson you should be able to:

  • Model a projectile as two independent motions: uniform velocity horizontally and uniform acceleration g vertically.
  • Derive the time of flight, maximum height, horizontal range and the equation of the trajectory.
  • Solve projectile problems on level ground, from a height, and for a target at a given range, including the two possible launch angles.

Theory

A projectile is a body launched into the air and then left to move under gravity alone, such as spoil thrown from a conveyor, a jet of water from a hose or dewatering pipe, or a stone flung by a blast. If air resistance is ignored, the only force is the weight, which acts vertically. The horizontal acceleration is therefore zero and the vertical acceleration is g downwards.

Using rectangular components (lesson 7.2), the motion splits into two simple rectilinear motions that share the same clock. Horizontally the velocity stays at u cos θ, so x = u cos θ · t. Vertically the motion is uniformly decelerated: y = u sin θ · t − ½ g t² and v_y = u sin θ − g t. Every projectile problem is solved by writing these two equations and linking them through the time t.

uθHRR = u² sin 2θ / gIndiacon original, not to scale
Figure 7.4: Drag-free projectile path: a parabola with maximum height H at mid-range and range R on level ground. Indiacon original, not to scale.

On level ground the projectile lands when y returns to zero, giving the time of flight T = 2 u sin θ / g. At the top of the path v_y = 0, giving the maximum height H = u² sin² θ / (2 g). The horizontal range is R = u cos θ · T = u² sin 2θ / g, which is greatest at θ = 45°. Because sin 2θ = sin (180° − 2θ), the complementary angles θ and 90° − θ give the same range: a low, fast path and a high, slow one.

Eliminating t gives the trajectory y = x tan θ − g x² / (2 u² cos² θ), a parabola with a vertical axis. Real projectiles at high speed are slowed by air drag, so their paths fall short of the parabola and are not symmetrical; the drag-free results are good for slow, dense objects over short distances and give an upper bound otherwise.

Derivation

  1. Horizontal: a_x = 0, so v_x = u cos θ and x = u cos θ · t.
  2. Vertical (up positive): a_y = −g, so v_y = u sin θ − g t and y = u sin θ · t − ½ g t².
  3. Time of flight on level ground: y = 0 gives t (u sin θ − ½ g t) = 0, so T = 2 u sin θ / g.
  4. Maximum height: v_y = 0 at t = u sin θ / g; substituting, H = u² sin² θ / (2 g).
  5. Range: R = u cos θ · T = 2 u² sin θ cos θ / g = u² sin 2θ / g; dR/dθ = 0 gives cos 2θ = 0, θ = 45°, R_max = u²/g.
  6. Trajectory: t = x / (u cos θ) in the y equation gives y = x tan θ − g x² / (2 u² cos² θ).
Formulas, symbols and SI units
  • x = u cos θ · t; y = u sin θ · t − ½ g t² (m)
  • v_x = u cos θ; v_y = u sin θ − g t (m/s)
  • Time of flight (level): T = 2 u sin θ / g (s)
  • Maximum height: H = u² sin² θ / (2g) (m)
  • Range (level): R = u² sin 2θ / g; R_max = u²/g at θ = 45°
  • Trajectory: y = x tan θ − g x² / (2 u² cos² θ)
  • Horizontal launch from height h: t = √(2h/g), x = u t
Assumptions and limits
  • Air resistance is neglected.
  • g is constant (9.81 m/s²) and the ground is flat over the range considered.
  • The projectile is a particle; spin and its effect on the path are ignored.
  • Level-ground formulas for T, H and R apply only when launch and landing are at the same height; otherwise use the component equations directly.

Codes and standards

Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.

  • No design code governs this lesson; projectile motion is a principle of mechanics.

Worked examples

Example 1 (exam style)

Problem. A ball is thrown from level ground at 20 m/s at 30° above the horizontal. Find the time of flight, the maximum height and the range (g = 9.81 m/s²).

  1. u sin θ = 10 m/s; u cos θ = 17.32 m/s.
  2. T = 2 × 10 / 9.81 = 2.039 s.
  3. H = 10² / (2 × 9.81) = 5.097 m.
  4. R = 20² × sin 60° / 9.81 = 35.31 m (check: 17.32 × 2.039 = 35.31 m).

Answer. T = 2.04 s; H = 5.10 m; R = 35.3 m

Example 2 (site style)

Problem. Excavated soil leaves the end of a horizontal conveyor belt at 3 m/s, 4 m above the ground. How far from the end of the belt does it land, and how fast is it moving on impact?

  1. Horizontal launch: θ = 0, so the vertical motion is a free fall from rest.
  2. t = √(2 × 4 / 9.81) = 0.9031 s.
  3. x = 3 × 0.9031 = 2.709 m from the end of the belt.
  4. v_y = 9.81 × 0.9031 = 8.859 m/s; impact speed = √(3² + 8.859²) = 9.353 m/s.

Answer. Lands 2.71 m out at 9.35 m/s; keep the stockpile and the exclusion zone at least this far out

Example 3 (exam style)

Problem. A hose delivers water at 15 m/s. At what angles must it be held to wet a point 12 m away at the same level?

  1. R = u² sin 2θ / g, so sin 2θ = 12 × 9.81 / 225 = 0.5232.
  2. 2θ = 31.55° or 148.45°.
  3. θ = 15.78° or 74.22°; the two angles add up to 90°.
  4. The low angle reaches the point sooner (T = 2 × 15 × sin 15.78° / 9.81 = 0.832 s, against 2.942 s for the high angle).

Answer. θ = 15.8° or 74.2°

Step-by-step procedure

  1. Draw the path, mark the launch point as the origin and take up as positive.
  2. Resolve the launch velocity: u cos θ horizontally, u sin θ vertically.
  3. Write x(t) and y(t); use the condition the problem gives (landing height, top of path, target x) to find t.
  4. Substitute t into the other equation for the unknown.
  5. Use the level-ground formulas only when launch and landing heights are equal; check the answer with the component equations.

Site notes

  • Material thrown from conveyors, chutes and skips follows a projectile path; the landing distance x = u √(2h/g) sets where the stockpile forms and how far the danger zone extends.
  • Blasting in quarries and rock cuttings can throw fragments a long way; since the drag-free range u²/g grows with the square of the launch speed, blast design and exclusion zones are set by specialist rules, not by this simple formula.
  • Water jets from dewatering pumps and fire hoses reach further than expected when aimed near 45°; aim low for a quick, flat jet and high to clear an obstacle.
Common mistakes
  • Using the level-ground range formula when the landing point is higher or lower than the launch point.
  • Applying g to the horizontal motion, or forgetting that the horizontal velocity stays constant.
  • Taking the velocity at the top of the path as zero; only the vertical component is zero there.
  • Mixing degrees and radians in a calculator.
  • Missing the second launch angle when solving sin 2θ = constant.
Quick check

Treat horizontal and vertical motions separately with the same clock: constant velocity sideways, constant acceleration g downwards.

Summary

  • x = u cos θ t; y = u sin θ t − ½ g t².
  • T = 2u sin θ/g; H = u² sin² θ/(2g); R = u² sin 2θ/g.
  • Maximum range at 45°; complementary angles give equal range.
  • The path is a parabola when air resistance is neglected.

Practice questions

Tap a question to see the answer.

1Find the range of a projectile launched at 30 m/s at 45° on level ground.

R = 900 / 9.81 = 91.74 m.

2Find the maximum height reached by a body projected at 25 m/s at 60°.

H = 625 × 0.75 / 19.62 = 23.89 m.

3A stone is thrown horizontally at 10 m/s from the top of a 20 m cut face. How far from the foot does it land?

t = √(40/9.81) = 2.019 s; x = 20.19 m.

4Find the time of flight of a projectile launched at 15 m/s at 40° on level ground.

T = 2 × 15 × sin 40° / 9.81 = 1.966 s.

5Show that launch angles of 25° and 65° give the same range.

sin 50° = sin 130°, so u² sin 2θ / g is the same for both.

6Find the greatest range possible with a launch speed of 10 m/s.

R_max = u²/g = 100 / 9.81 = 10.19 m at 45°.

References

Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.

  • F. P. Beer, E. R. Johnston, D. F. Mazurek, P. J. Cornwell, B. P. Self, Vector Mechanics for Engineers: Statics and Dynamics, McGraw Hill, 12th edition, 2019.
  • R. C. Hibbeler, Engineering Mechanics: Statics, Pearson, 15th edition, 2022 (published 2021).
  • J. L. Meriam, L. G. Kraige, J. N. Bolton, Engineering Mechanics: Statics, Wiley, 9th edition, 2018.
  • S. Timoshenko, D. H. Young, J. V. Rao, S. Pati, Engineering Mechanics (in SI units), McGraw Hill Education (India), 5th edition, 2013.
Suggest a correction

If something on this page is wrong, tell the editor. Your message is sent privately and is not published.

Sent privately to the Indiacon editor; not published.