7.1 Rectilinear motion
After this lesson you should be able to:
- Define position, displacement, distance, velocity and acceleration for a particle moving along a straight line, with their SI units and signs.
- Derive and use the three constant-acceleration equations, and know when they must not be used.
- Find velocity and acceleration from a position function by differentiation, find position from a varying acceleration by integration, and read motion from velocity-time graphs.
Theory
Kinematics describes motion without asking what causes it. The simplest case is a particle moving along a straight line, called rectilinear motion. Its position is a single coordinate x measured from a fixed origin, with a chosen positive direction. A vehicle braking on a straight road, a lift car in its shaft, a pile hammer falling and a train leaving a station are all modelled this way.
Velocity is the rate of change of position, v = dx/dt, and acceleration is the rate of change of velocity, a = dv/dt = d²x/dt². Both are signed quantities: a negative velocity means motion in the negative direction, and a negative acceleration means the velocity is decreasing algebraically, which slows the particle only if v is positive. Displacement is the change in position between two instants; distance travelled is the total length of path covered, and the two differ whenever the particle reverses direction.
Eliminating time with the chain rule gives a third relation, a = v dv/dx. It is the right tool when the acceleration is given as a function of position or velocity, for example the deceleration of a vehicle in an arrester bed or the pull of a spring. When the acceleration is constant, integration gives the familiar equations v = u + a t, s = u t + ½ a t² and v² = u² + 2 a s. They apply only while a stays constant; a motion made of several phases must be split into phases.
Graphs carry the same information. The slope of the position-time graph is the velocity, the slope of the velocity-time graph is the acceleration, and the area under the velocity-time graph between two instants is the displacement in that interval. The area under the speed-time graph is the distance travelled. Many site problems, such as a train run between stations, are solved fastest by drawing the velocity-time graph and adding areas.
Derivation
- Start from a = dv/dt with a constant. Integrating from t = 0 (v = u) to t gives v = u + a t.
- Since v = dx/dt = u + a t, integrating from x = 0 at t = 0 gives s = u t + ½ a t².
- Using a = dv/dt = (dv/dx)(dx/dt) = v dv/dx, constant a gives ∫ v dv from u to v = a ∫ dx from 0 to s, so ½ (v² − u²) = a s and v² = u² + 2 a s.
- Eliminating a between the first two gives s = ½ (u + v) t: the displacement equals the average of the initial and final velocities times the time, true only for constant acceleration.
- For a varying acceleration a(t), v(t) = u + ∫ a dt and x(t) = x₀ + ∫ v dt; for a(x), use v dv = a(x) dx; for a(v), use dt = dv / a(v) or dx = v dv / a(v).
v = dx/dt (m/s); a = dv/dt = d²x/dt² = v dv/dx (m/s²)Constant a: v = u + a tConstant a: s = u t + ½ a t²Constant a: v² = u² + 2 a sConstant a: s = ½ (u + v) tUnit change: 1 km/h = 1/3.6 m/sDisplacement = area under the v-t graph; distance = area under the speed-t graph
- The body is treated as a particle: its size and rotation do not affect the answer.
- Motion is along one fixed straight line, so position needs one coordinate.
- The constant-acceleration equations hold only while the acceleration is constant; split the motion into phases otherwise.
- Free fall uses g = 9.81 m/s² and neglects air resistance, which is reasonable for short, slow drops of dense objects.
Codes and standards
Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.
- No design code governs this lesson; rectilinear kinematics is a principle of mechanics. Highway design uses the braking result in the stopping sight distance taught in the highway engineering subject.
Worked examples
Problem. A car travelling at 72 km/h on a level road sees an obstruction. The driver takes 2.5 s to react and then brakes with a uniform deceleration of 4 m/s². Find the distance covered during the reaction time, the braking distance, the braking time and the total stopping distance.
- u = 72 / 3.6 = 20 m/s.
- Reaction (lag) distance at constant speed = 20 × 2.5 = 50 m.
- Braking distance from v² = u² + 2 a s with v = 0 and a = −4 m/s²: s = 20² / (2 × 4) = 50 m.
- Braking time from v = u + a t: t = 20 / 4 = 5 s.
- Total stopping distance = 50 + 50 = 100 m.
Answer. Reaction distance 50 m; braking distance 50 m in 5 s; total 100 m
Problem. The position of a particle is x = t³ − 6t² + 9t + 5, with x in metres and t in seconds. Find the velocity and acceleration at t = 2 s, the instants when the particle stops, and the displacement and distance travelled from t = 0 to t = 4 s.
- v = dx/dt = 3t² − 12t + 9 = 3 (t − 1)(t − 3); a = dv/dt = 6t − 12.
- At t = 2 s: v = 12 − 24 + 9 = −3 m/s and a = 0.
- The particle stops when v = 0: at t = 1 s and t = 3 s.
- Positions: x(0) = 5 m, x(1) = 9 m, x(3) = 5 m, x(4) = 9 m.
- Displacement = 9 − 5 = 4 m. Distance = |9 − 5| + |5 − 9| + |9 − 5| = 4 + 4 + 4 = 12 m.
Answer. v(2) = −3 m/s, a(2) = 0; stops at 1 s and 3 s; displacement 4 m; distance 12 m
Problem. A steel bolt is dropped from a bridge deck 45 m above the water. Ignoring air resistance, find the time it takes to reach the water and its speed on impact.
- Take downwards as positive: u = 0, a = g = 9.81 m/s², s = 45 m.
- s = ½ g t², so t = √(2 × 45 / 9.81) = 3.029 s.
- v² = 2 g s, so v = √(2 × 9.81 × 45) = 29.71 m/s (about 107 km/h).
- This is why toe boards and nets are needed on bridge decks: even a small object arrives fast.
Answer. t = 3.03 s; v = 29.7 m/s
Step-by-step procedure
- Choose an origin and a positive direction and keep them for the whole problem.
- Convert all data to SI units (km/h to m/s by dividing by 3.6).
- Decide whether the acceleration is constant. If yes, use the three equations phase by phase; if not, differentiate or integrate (a = dv/dt or a = v dv/dx).
- Find the instants where v = 0 before computing distance travelled, and add the absolute values of the displacements between them.
- For multi-phase motion, sketch the v-t graph and use slopes and areas as a check.
Site notes
- Stopping distance has two parts: the distance covered at full speed while the driver reacts, and the braking distance, which grows with the square of the speed. Doubling the speed doubles the first part but quadruples the second.
- In a lift or hoist the acceleration and deceleration phases are short and the cruise phase long; the v-t graph of a hoist cycle is a trapezium, and its area is the travel height.
- Dropped objects gain speed quickly: after a 20 m fall the speed is already about 20 m/s, which is why exclusion zones are set below any work at height.
- Using the constant-acceleration equations when the acceleration varies with time, position or velocity.
- Mixing km/h and m/s in the same equation.
- Reporting displacement when the question asks for distance travelled, or forgetting to split the motion at the instants where v = 0.
- Losing the sign of g: if upwards is positive, a = −9.81 m/s² for a freely moving body.
- Treating a negative acceleration as always meaning "slowing down"; it slows the particle only when the velocity is positive.
Before using v² = u² + 2as, ask whether the acceleration is truly constant over the whole interval; if not, split the motion or integrate.
Summary
- v = dx/dt, a = dv/dt = v dv/dx.
- Constant a: v = u + at, s = ut + ½at², v² = u² + 2as.
- Area under the v-t graph is displacement; slope is acceleration.
- Distance travelled differs from displacement when the particle reverses.
Practice questions
Tap a question to see the answer.
1A train starts from rest with a uniform acceleration of 0.5 m/s². Find its speed and the distance covered after 60 s.
v = 0.5 × 60 = 30 m/s (108 km/h); s = ½ × 0.5 × 60² = 900 m.
2A vehicle accelerates uniformly from rest to 20 m/s in 10 s, runs at 20 m/s for 30 s and then stops uniformly in 8 s. Find the total distance.
Area of the v-t graph: 100 + 600 + 80 = 780 m.
3A stone is thrown vertically up at 19.62 m/s. Find the maximum height and the time to reach it (g = 9.81 m/s²).
t = 19.62 / 9.81 = 2 s; h = 19.62² / (2 × 9.81) = 19.62 m.
4A particle starts from rest at x = 0 with a = 4 − 2t m/s². Find its maximum velocity and its position when this occurs.
v = 4t − t², maximum when a = 0 at t = 2 s: v = 4 m/s; x = 2t² − t³/3 = 8 − 8/3 = 5.333 m.
5A hoist cage starts from rest with an upward acceleration of 2 m/s² for 3 s. Find its speed and the height gained.
v = 2 × 3 = 6 m/s; s = ½ × 2 × 3² = 9 m.
6Convert 90 km/h into m/s.
90 / 3.6 = 25 m/s.
References
Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.
- F. P. Beer, E. R. Johnston, D. F. Mazurek, P. J. Cornwell, B. P. Self, Vector Mechanics for Engineers: Statics and Dynamics, McGraw Hill, 12th edition, 2019.
- R. C. Hibbeler, Engineering Mechanics: Statics, Pearson, 15th edition, 2022 (published 2021).
- J. L. Meriam, L. G. Kraige, J. N. Bolton, Engineering Mechanics: Statics, Wiley, 9th edition, 2018.
- S. Timoshenko, D. H. Young, J. V. Rao, S. Pati, Engineering Mechanics (in SI units), McGraw Hill Education (India), 5th edition, 2013.