5.1 Second moment of area by integration
After this lesson you should be able to:
- Define the second moment of area (area moment of inertia) of a plane area about an axis and the polar moment about a point.
- Derive the standard results for a rectangle, triangle, circle and semicircle by integration.
- Find the radius of gyration of a section and explain why depth matters more than width in bending.
Theory
The first moment of area, used in Chapter 4 to locate centroids, weights each small element dA by its distance from an axis. The second moment of area weights each element by the square of that distance: I_x = ∫ y² dA about the x axis and I_y = ∫ x² dA about the y axis. Because the distance is squared, material far from the axis counts much more than material near it, and the result is always positive.
This quantity has nothing to do with mass or rotation in this lesson; the name moment of inertia is borrowed from dynamics because the integral has the same form. In structural engineering it measures how well a cross-section resists bending: the bending stress in a beam is M y / I and the curvature is M / (E I), so a larger I gives lower stresses and smaller deflections for the same moment. Strength of materials and structural analysis use it on almost every page.
The polar moment of area about a point O in the plane is J_O = ∫ r² dA, where r is the distance from O. Since r² = x² + y², J_O = I_x + I_y for any pair of perpendicular axes through O. The polar moment governs the twisting of circular shafts and piles under torque.
The radius of gyration k is the distance at which the whole area, if concentrated in a thin strip, would have the same second moment: I = A k², so k = √(I / A). It has units of length and is used in column buckling, where the slenderness ratio is the effective length divided by k. Units of I are length to the fourth power, normally mm⁴ for sections; 1 m⁴ = 10¹² mm⁴.
Derivation
- Rectangle b × h about its base: take a horizontal strip of width b and thickness dy at height y, so dA = b dy. Then I_base = ∫₀ʰ y² b dy = b h³ / 3.
- Rectangle about its centroidal axis parallel to the base: integrate from −h/2 to h/2, giving I_c = b [y³/3] from −h/2 to h/2 = b h³ / 12.
- Triangle of base b and height h about its base: a strip at height y has width b (h − y)/h, so I_base = ∫₀ʰ y² b (h − y)/h dy = b h³ / 12. About the centroidal axis parallel to the base the result is b h³ / 36 (shown with the parallel axis theorem in lesson 5.2).
- Circle of radius r about its centre: use rings of radius ρ and thickness dρ, dA = 2π ρ dρ, so J_O = ∫₀ʳ ρ² 2π ρ dρ = π r⁴ / 2. By symmetry I_x = I_y = J_O / 2 = π r⁴ / 4 = π d⁴ / 64.
- Semicircle about its diameter: it is half the circle, so I = π r⁴ / 8. About its own centroidal axis parallel to the diameter, subtract A ȳ² with ȳ = 4r/(3π): I_c = (π/8 − 8/(9π)) r⁴ ≈ 0.1098 r⁴.
I_x = ∫ y² dA, I_y = ∫ x² dA (mm⁴ or m⁴)J_O = ∫ r² dA = I_x + I_yRectangle: I_c = b h³ / 12, I_base = b h³ / 3Triangle: I_base = b h³ / 12, I_c = b h³ / 36Circle: I = π d⁴ / 64, J = π d⁴ / 32; hollow circle: I = π (D⁴ − d⁴) / 64Semicircle: I_diameter = π r⁴ / 8, I_c ≈ 0.1098 r⁴Radius of gyration: k = √(I / A) (mm)
- The area is plane and the axis lies in its plane (for I_x, I_y) or is normal to it through O (for J_O).
- Sections are treated as ideal shapes; root fillets, chamfers and holes are ignored unless included as separate parts.
- Second moments of area are purely geometric; material properties enter only later through E I.
Codes and standards
Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.
- No design code governs this geometry. Design codes use the results: IS 456:2000 and IS 800:2007 both work with section second moments and section moduli derived from the integrals of this lesson.
Worked examples
Problem. A reinforced concrete beam is 300 mm wide and 600 mm deep. Find its gross second moment of area about the horizontal centroidal axis and about the soffit, and its radius of gyration about the centroidal axis.
- I_c = b h³ / 12 = 300 × 600³ / 12 = 5.400 × 10⁹ mm⁴.
- I_soffit = b h³ / 3 = 300 × 600³ / 3 = 2.160 × 10¹⁰ mm⁴, four times I_c.
- A = 300 × 600 = 180 000 mm², so k = √(5.400 × 10⁹ / 180 000) = 173.2 mm, which is h/√12.
Answer. I_c = 5.400 × 10⁹ mm⁴; I_soffit = 2.160 × 10¹⁰ mm⁴; k = 173.2 mm
Problem. A triangular area has a base of 200 mm and a height of 300 mm. Find its second moment of area about the base by integration, and about the centroidal axis parallel to the base. Find the radius of gyration about the centroidal axis.
- Strip at height y: width = 200 (300 − y)/300, dA = width × dy.
- I_base = ∫₀³⁰⁰ y² × 200 (300 − y)/300 dy = 200 × 300³ / 12 = 4.500 × 10⁸ mm⁴.
- I_c = b h³ / 36 = 200 × 300³ / 36 = 1.500 × 10⁸ mm⁴.
- A = 30 000 mm², so k_c = √(1.500 × 10⁸ / 30 000) = 70.71 mm.
Answer. I_base = 4.500 × 10⁸ mm⁴; I_c = 1.500 × 10⁸ mm⁴; k = 70.71 mm
Step-by-step procedure
- Choose the axis and set up coordinates with the axis as y = 0 (or x = 0).
- Choose a strip parallel to the axis so every point of the strip is at the same distance from it.
- Write dA in terms of one variable and the strip width.
- Integrate distance squared times dA over the area; check the units come out as length⁴.
- Find k = √(I/A) if a radius of gyration is needed.
Site notes
- Doubling the depth of a rectangular beam multiplies I by eight, while doubling the width only doubles it; this is why beams are deep and narrow, and why a plank laid flat sags far more than one on edge.
- A precast or bored pile of circular section has I = π d⁴/64; a 500 mm pile has I = 3.068 × 10⁹ mm⁴ about any diameter, the same in every direction.
- Hollow circular sections such as pipe piles and poles keep most of the I of a solid section with much less material, because the removed core is near the axis.
- Using b h³/3 (about the base) where the centroidal value b h³/12 is needed, or the other way round.
- Mixing up b and h: h is the dimension perpendicular to the axis and is the one that is cubed.
- Confusing the radius of gyration with the distance to the centroid.
- Converting mm⁴ to m⁴ with 10⁶ instead of 10¹².
- Calling I a mass property; here it is purely geometric.
For a rectangle the cubed dimension is always the one perpendicular to the axis; if your I barely changes when you double the depth, you have cubed the wrong side.
Summary
- I_x = ∫ y² dA; the squared distance makes far material count most.
- Rectangle b h³/12 about the centroid, b h³/3 about the base; triangle b h³/36 and b h³/12.
- Circle π d⁴/64; polar moment J = I_x + I_y = π d⁴/32.
- k = √(I/A) is used in buckling and slenderness.
Practice questions
Tap a question to see the answer.
1Find I of a 500 mm diameter circular pile about a diameter, and its radius of gyration.
I = π × 500⁴ / 64 = 3.068 × 10⁹ mm⁴; k = d/4 = 125 mm.
2Find I of a hollow circular pole of outer diameter 300 mm and inner diameter 250 mm, and its radius of gyration.
I = π (300⁴ − 250⁴)/64 = 2.059 × 10⁸ mm⁴; A = 21 598 mm², k = 97.63 mm.
3Find I of a semicircle of radius 100 mm about its diameter and about its own centroidal axis parallel to the diameter.
About the diameter π r⁴/8 = 3.927 × 10⁷ mm⁴; about the centroid 0.1098 r⁴ = 1.098 × 10⁷ mm⁴.
4Find I of a 100 mm wide × 200 mm deep rectangle about its base.
b h³/3 = 100 × 200³/3 = 2.667 × 10⁸ mm⁴.
5By what factor does I_c change if the depth of a rectangular beam is doubled and its width is halved?
I ∝ b h³, so the factor is 0.5 × 2³ = 4.
6Find the polar moment of area of a 200 mm square about its centre.
J = I_x + I_y = 2 × 200⁴/12 = 2.667 × 10⁸ mm⁴.
References
Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.
- F. P. Beer, E. R. Johnston, D. F. Mazurek, P. J. Cornwell, B. P. Self, Vector Mechanics for Engineers: Statics and Dynamics, McGraw Hill, 12th edition, 2019.
- R. C. Hibbeler, Engineering Mechanics: Statics, Pearson, 15th edition, 2022 (published 2021).
- J. L. Meriam, L. G. Kraige, J. N. Bolton, Engineering Mechanics: Statics, Wiley, 9th edition, 2018.
- S. Timoshenko, D. H. Young, J. V. Rao, S. Pati, Engineering Mechanics (in SI units), McGraw Hill Education (India), 5th edition, 2013.