Indiacon CivilSubscribe

Textbook › Engineering Mechanics › Chapter 5 › Lesson 5.4

5.4 Product of inertia and principal axes

Engineering Mechanics Chapter 5: Moment of inertia Under review — not yet three-checked Author: Indiacon

Learning objectives

After this lesson you should be able to:

  • Define the product of inertia of a plane area and transfer it between parallel axes.
  • Find second moments about rotated axes and locate the principal axes and principal second moments.
  • Use Mohr's circle as a graphical check, and recognise sections whose principal axes are inclined, such as unequal angles.

Theory

The product of inertia of a plane area about the x and y axes is I_xy = ∫ x y dA. Unlike I_x and I_y it can be positive, negative or zero, because x y changes sign from quadrant to quadrant. If either axis is an axis of symmetry, every element on one side is matched by a mirror element on the other with x y of opposite sign, so I_xy = 0.

The product of inertia tells us how the second moment changes when the axes are rotated. For axes u and v turned through an angle θ anticlockwise from x and y about the same origin, the second moments I_u, I_v and the product I_uv depend on I_x, I_y and I_xy only, through formulas in 2θ. These are the same transformation equations used for plane stress and strain, so the same Mohr's circle construction applies.

major principal axis (about 24°)xytan 2θp = −2Ixy/(Ix − Iy)Indiacon original, not to scale
Figure 5.4: An unequal angle: its centroidal axes parallel to the legs are not principal; the principal axes are inclined at about 24 degrees. Indiacon original, not to scale.

As θ changes, I_u passes through a maximum and a minimum at two perpendicular directions called the principal axes, where I_uv = 0. The principal second moments I₁ and I₂ are the largest and smallest second moments for any axis through that point. For a section with an axis of symmetry, that axis is a principal axis.

Principal axes matter in design because a beam bends simply, without twisting sideways, only about a principal axis. An unequal angle or a Z-section loaded vertically bends about inclined principal axes and deflects partly sideways, which is why the minimum radius of gyration about the minor principal axis governs the buckling of angle struts.

Derivation

  1. For a point with coordinates (x, y), the rotated coordinates are u = x cos θ + y sin θ and v = y cos θ − x sin θ.
  2. I_u = ∫ v² dA = I_x cos²θ + I_y sin²θ − 2 I_xy sin θ cos θ. Using double-angle identities: I_u = (I_x + I_y)/2 + (I_x − I_y)/2 cos 2θ − I_xy sin 2θ.
  3. Similarly I_v = (I_x + I_y)/2 − (I_x − I_y)/2 cos 2θ + I_xy sin 2θ and I_uv = (I_x − I_y)/2 sin 2θ + I_xy cos 2θ. Note I_u + I_v = I_x + I_y.
  4. Setting dI_u/dθ = 0 gives tan 2θ_p = −2 I_xy / (I_x − I_y); at this angle I_uv = 0.
  5. Substituting back: I₁,₂ = (I_x + I_y)/2 ± √[((I_x − I_y)/2)² + I_xy²].
  6. Parallel axis theorem for the product: I_xy = I_x′y′ + A d_x d_y, where d_x and d_y are the coordinates of the centroid in the x–y system (signs kept).
Formulas, symbols and SI units
  • I_xy = ∫ x y dA (mm⁴, may be negative)
  • Parallel axis: I_xy = I_x′y′ + A d_x d_y
  • Rotation: I_u = (I_x + I_y)/2 + (I_x − I_y)/2 cos 2θ − I_xy sin 2θ
  • I_uv = (I_x − I_y)/2 sin 2θ + I_xy cos 2θ
  • Principal angle: tan 2θ_p = −2 I_xy / (I_x − I_y)
  • Principal values: I₁,₂ = (I_x + I_y)/2 ± √[((I_x − I_y)/2)² + I_xy²]
  • Rectangle about two adjacent edges: I_xy = b² h² / 4
Assumptions and limits
  • θ is measured anticlockwise from the x axis; with this sign convention the formulas above apply as written. Other textbooks may define the angle or I_xy sign differently, so check the convention before using a formula.
  • All axes pass through the same point; for principal centroidal axes that point is the centroid.
  • Root and toe radii of rolled angles are ignored in hand calculations; section tables include them.

Codes and standards

Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.

  • Dimensions of rolled equal and unequal angles are tabulated in IS 808:1989; IS 800:2007 uses the minimum radius of gyration of angle sections when checking angle struts.

Worked examples

Example 1 (exam style)

Problem. An unequal angle has a 150 mm vertical leg and a 100 mm horizontal leg, both 10 mm thick (fillets ignored), with the outer corner at the origin. Find the centroid, I_x, I_y and I_xy about centroidal axes parallel to the legs, the principal second moments and the orientation of the principal axes.

  1. Split into the vertical leg 10 × 150 (A₁ = 1 500 mm², centroid (5, 75)) and the rest of the horizontal leg 90 × 10 (A₂ = 900 mm², centroid (55, 5)).
  2. x̄ = (1 500 × 5 + 900 × 55)/2 400 = 23.75 mm; ȳ = (1 500 × 75 + 900 × 5)/2 400 = 48.75 mm.
  3. I_x = 10 × 150³/12 + 1 500 × 26.25² + 90 × 10³/12 + 900 × 43.75² = 5.576 × 10⁶ mm⁴.
  4. I_y = 150 × 10³/12 + 1 500 × 18.75² + 10 × 90³/12 + 900 × 31.25² = 2.026 × 10⁶ mm⁴.
  5. I_xy = 1 500 × (−18.75)(26.25) + 900 × (31.25)(−43.75) = −1.969 × 10⁶ mm⁴ (the parts have zero centroidal products).
  6. Average 3.801 × 10⁶, radius √(1.775² + 1.969²) × 10⁶ = 2.651 × 10⁶, so I₁ = 6.452 × 10⁶ mm⁴ and I₂ = 1.150 × 10⁶ mm⁴.
  7. tan 2θ_p = 3.9375/3.550 = 1.109, so θ_p = 23.98° anticlockwise from x for the major axis (substituting into I_u confirms it gives I₁).

Answer. x̄ = 23.75 mm, ȳ = 48.75 mm; I_x = 5.576 × 10⁶, I_y = 2.026 × 10⁶, I_xy = −1.969 × 10⁶ mm⁴; I₁ = 6.452 × 10⁶ mm⁴ at 23.98°, I₂ = 1.150 × 10⁶ mm⁴

Example 2 (site style)

Problem. A 300 mm wide × 600 mm deep rectangular rafter section is used with its depth tilted 30° from the line of a vertical load. Find the second moments about centroidal axes u and v rotated 30° from the section's own axes, and the product I_uv.

  1. About its own centroidal axes: I_x = 300 × 600³/12 = 5.400 × 10⁹ mm⁴, I_y = 600 × 300³/12 = 1.350 × 10⁹ mm⁴, I_xy = 0 (both are axes of symmetry).
  2. Average 3.375 × 10⁹; half-difference 2.025 × 10⁹.
  3. I_u = 3.375 × 10⁹ + 2.025 × 10⁹ × cos 60° = 4.388 × 10⁹ mm⁴.
  4. I_v = 3.375 × 10⁹ − 2.025 × 10⁹ × cos 60° = 2.363 × 10⁹ mm⁴.
  5. I_uv = 2.025 × 10⁹ × sin 60° = 1.754 × 10⁹ mm⁴; it is not zero, so u and v are not principal axes and the member bends about both of its own axes under the vertical load.

Answer. I_u = 4.388 × 10⁹ mm⁴, I_v = 2.363 × 10⁹ mm⁴, I_uv = 1.754 × 10⁹ mm⁴

Step-by-step procedure

  1. Find the centroid and I_x, I_y about centroidal axes (lesson 5.3).
  2. Find I_xy of each part about the section centroid with I_xy = I_x′y′ + A d_x d_y, keeping signs, and add.
  3. Compute the principal angle from tan 2θ_p and the principal values from the square-root formula.
  4. Substitute θ_p into I_u to tell which principal axis is the major one.
  5. Check: I₁ + I₂ = I_x + I_y.

Site notes

  • Single angles used as bracing struts buckle about their minor principal axis, not about an axis parallel to a leg; use the minimum radius of gyration from the section table.
  • Purlins and rafters on sloping roofs carry vertical loads at an angle to their principal axes, so they bend about both axes; sag rods are often added to control the weaker-axis bending.
  • A section with any axis of symmetry needs no principal-axis calculation: the symmetry axis and the axis perpendicular to it are principal.
Common mistakes
  • Dropping the sign of d_x d_y in the parallel axis term for I_xy.
  • Mixing sign conventions from two textbooks in one calculation.
  • Taking θ_p from tan 2θ_p without checking whether it gives the major or the minor axis.
  • Forgetting that I_xy of a symmetric part about its own centroidal axes is zero.
  • Using a leg-parallel radius of gyration for angle buckling.
Quick check

I₁ + I₂ must equal I_x + I_y, and the principal values must bracket both I_x and I_y; if not, recheck I_xy.

Summary

  • I_xy = ∫ x y dA; zero if either axis is a symmetry axis.
  • Rotation formulas in 2θ, identical in form to plane stress transformation.
  • Principal axes: I_uv = 0, tan 2θ_p = −2 I_xy/(I_x − I_y).
  • Unsymmetric sections bend and buckle about inclined principal axes.

Practice questions

Tap a question to see the answer.

1Find I_xy of a 100 mm wide × 200 mm deep rectangle about axes along its bottom and left edges.

I_xy = b² h²/4 = 100² × 200²/4 = 1.0 × 10⁸ mm⁴.

2A section has I_x = 6 × 10⁶, I_y = 2 × 10⁶ and I_xy = −2 × 10⁶ mm⁴. Find the principal second moments and angle.

I₁,₂ = 4 × 10⁶ ± 2.828 × 10⁶: I₁ = 6.828 × 10⁶, I₂ = 1.172 × 10⁶ mm⁴; tan 2θ_p = 1, θ_p = 22.5° anticlockwise for I₁.

3A section has I_x = 5 × 10⁶, I_y = 3 × 10⁶ and I_xy = 0 mm⁴. Find I_u and I_uv for axes rotated 30°.

I_u = 4 × 10⁶ + 1 × 10⁶ × 0.5 = 4.5 × 10⁶ mm⁴; I_uv = 1 × 10⁶ × 0.866 = 8.66 × 10⁵ mm⁴.

4Where are the principal centroidal axes of an equal angle?

Along the axis of symmetry (at 45° to the legs) and perpendicular to it; the major axis is the one perpendicular to the symmetry axis.

5Why is I_xy of a channel zero about centroidal axes parallel to its flanges and web?

The axis parallel to the flanges through the centroid is an axis of symmetry, so I_xy = 0.

References

Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.

  • F. P. Beer, E. R. Johnston, D. F. Mazurek, P. J. Cornwell, B. P. Self, Vector Mechanics for Engineers: Statics and Dynamics, McGraw Hill, 12th edition, 2019.
  • R. C. Hibbeler, Engineering Mechanics: Statics, Pearson, 15th edition, 2022 (published 2021).
  • J. L. Meriam, L. G. Kraige, J. N. Bolton, Engineering Mechanics: Statics, Wiley, 9th edition, 2018.
  • S. Timoshenko, D. H. Young, J. V. Rao, S. Pati, Engineering Mechanics (in SI units), McGraw Hill Education (India), 5th edition, 2013.
Suggest a correction

If something on this page is wrong, tell the editor. Your message is sent privately and is not published.

Sent privately to the Indiacon editor; not published.