4.3 Centroids of composite areas
After this lesson you should be able to:
- Find the centroid of a composite area by dividing it into simple shapes and tabulating areas and first moments.
- Treat holes and cut-outs as negative areas.
- Locate the neutral axis position of T, I, L and plate sections used in beams and connections.
Theory
Most sections in civil engineering are built from simple shapes: rectangles, triangles, circles and the standard curved shapes of the previous lesson. A T-beam is two rectangles, an angle section is two rectangles, a plate with a bolt hole is a rectangle minus a circle. Because integration is additive, the first moment of the whole is the sum of the first moments of the parts. So the centroid can be found without any new integration.
The work is best set out in a table with one row per part: its area Ai, the coordinates of its own centroid (xi, yi), and the products Ai xi and Ai yi. The centroid of the composite is x̄ = ΣAi xi / ΣAi and ȳ = ΣAi yi / ΣAi. A hole, a notch or a cut-out is entered as a negative area at its own centroid. This is exactly the same principle as a counterweight entered with a negative coordinate in lesson 4.1.
For a section that is symmetric about an axis, the centroid lies on that axis and only one coordinate needs to be calculated. In a beam, the centroidal axis of the section is the neutral axis in elastic bending, so this calculation is the first step in finding bending stresses, the moment of inertia and the section modulus in later chapters.
The same table works for lines (wires and bent bars, using lengths) and for volumes (using volumes, or weights when parts have different unit weights).
Derivation
- Let a composite area A be made of parts A1, A2, ..., An with centroids (x1, y1), ..., (xn, yn).
- By definition of the centroid of each part, ∫ over part i of x dA = Ai xi.
- The integral over the whole is the sum of integrals over the parts: ∫x dA = Σ Ai xi.
- Hence x̄ = Σ Ai xi / Σ Ai, and similarly ȳ = Σ Ai yi / Σ Ai.
- If a region is removed, its integral is subtracted: entering it with area −Ai at its own centroid gives the correct total.
x̄ = Σ Ai xi / Σ Ai, ȳ = Σ Ai yi / Σ Ai (mm or m)Hole or cut-out: enter −Ai at its own centroidRectangle b × d: centroid at b/2, d/2; circle: at its centreLine composite: x̄ = Σ Li xi / Σ Li
- The parts do not overlap, or any overlap is removed once as a negative area.
- Each part is homogeneous with uniform thickness; for different materials, weight the areas (see lesson 4.1).
- Fillets and root radii of rolled sections are ignored in hand calculations unless stated; published section tables include them, so small differences are expected.
Codes and standards
Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.
- No design code governs this lesson. The centroid found here is used in IS 456:2000 and IS 800:2007 design of beams through the section properties derived in Chapter 5; those codes do not change how the centroid is found.
Worked examples
Problem. A T-section has a flange 200 mm wide and 20 mm thick on top of a web 20 mm thick and 180 mm deep (overall depth 200 mm). Find the height of the centroid above the bottom of the web.
- The section is symmetric about the vertical axis, so only ȳ is needed. Measure y from the bottom of the web.
- Flange: A1 = 200 × 20 = 4 000 mm², y1 = 180 + 10 = 190 mm, A1 y1 = 760 000 mm³.
- Web: A2 = 20 × 180 = 3 600 mm², y2 = 90 mm, A2 y2 = 324 000 mm³.
- ΣA = 7 600 mm², ΣAy = 1 084 000 mm³, so ȳ = 1 084 000 / 7 600 = 142.6 mm above the bottom (57.4 mm below the top).
Answer. ȳ = 142.6 mm from the bottom of the web
Problem. A steel base plate is 400 mm wide and 300 mm high with one 100 mm diameter hole whose centre is 100 mm from the left edge and 100 mm from the bottom edge. Find the centroid of the plate, measured from the bottom-left corner.
- Plate: A1 = 400 × 300 = 120 000 mm² at (200, 150).
- Hole: A2 = −π × 50² = −7 854 mm² at (100, 100).
- ΣA = 112 146 mm²; ΣAx = 24 000 000 − 785 398 = 23 214 602 mm³; ΣAy = 18 000 000 − 785 398 = 17 214 602 mm³.
- x̄ = 23 214 602 / 112 146 = 207.0 mm; ȳ = 17 214 602 / 112 146 = 153.5 mm. Removing the hole moves the centroid 7.0 mm right and 3.5 mm up, away from the hole.
Answer. Centroid at (207.0 mm, 153.5 mm)
Step-by-step procedure
- Sketch the section and choose a reference corner or edge for the axes.
- Divide into simple parts; mark holes and cut-outs as negative.
- Tabulate Ai, xi, yi, Ai xi, Ai yi for every part.
- Add the columns and divide to get x̄ and ȳ.
- Check symmetry and that the centroid moves away from any hole and towards the larger parts.
Site notes
- A beam with a large service opening in the web or a notched end has a shifted centroid at that section; ask for the designer's check rather than assuming the full-section properties.
- Built-up sections made by welding plates to a rolled section have a new centroid; bolt or weld groups and bearing stiffeners are set out from it.
- For precast units with lifting inserts, the inserts are placed symmetrically about the centroid of the unit in plan so that it hangs level.
- Forgetting to subtract the hole, or subtracting it at the wrong position.
- Measuring part centroids from different reference lines.
- Using the overall depth instead of the part depth when finding a part centroid.
- Rounding part results too early, which matters when large positive and negative terms nearly cancel.
- Assuming the centroid of a T-section is at mid-depth.
For a T-section the centroid lies in the half of the depth that contains the flange, and for a thin equal angle (leg thickness about one tenth of the leg length) it lies on the 45° line of symmetry, a little under 0.3 of the leg length from the back of each leg.
Summary
- Divide, tabulate, sum, divide: x̄ = ΣAx / ΣA.
- Holes and cut-outs are negative areas at their own centroids.
- On an axis of symmetry, only one coordinate is needed.
- The centroidal axis of a beam section is its elastic neutral axis.
Practice questions
Tap a question to see the answer.
1Find the centroid of an equal angle 100 × 100 × 10 mm (ignore the root radius), from the back of each leg.
Parts 100 × 10 (A = 1 000 mm² at 50, 5) and 10 × 90 (A = 900 mm² at 5, 55): x̄ = ȳ = (1 000 × 50 + 900 × 5)/1 900 = 28.7 mm.
2An I-section has a top flange 150 × 20 mm, a web 10 × 260 mm and a bottom flange 250 × 20 mm; overall depth 300 mm. Find ȳ from the bottom.
ΣA = 5 000 + 2 600 + 3 000 = 10 600 mm²; ΣAy = 5 000 × 10 + 2 600 × 150 + 3 000 × 290 = 1 310 000 mm³; ȳ = 123.6 mm.
3A rectangle 300 mm wide and 200 mm high has a semicircle of radius 100 mm cut from the middle of its top edge. Find ȳ from the bottom edge.
Semicircle area 15 708 mm² with centroid 200 − 42.44 = 157.56 mm; ȳ = (60 000 × 100 − 15 708 × 157.56)/44 292 = 79.6 mm.
4For the T-section of Example 1, how far below the top of the flange is the centroid?
200 − 142.6 = 57.4 mm.
5Why is a hole entered as a negative area at its own centroid?
Because the first moment is an integral, and removing a region subtracts exactly its area times its centroid distance from the total.
References
Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.
- F. P. Beer, E. R. Johnston, D. F. Mazurek, P. J. Cornwell, B. P. Self, Vector Mechanics for Engineers: Statics and Dynamics, McGraw Hill, 12th edition, 2019.
- R. C. Hibbeler, Engineering Mechanics: Statics, Pearson, 15th edition, 2022 (published 2021).
- J. L. Meriam, L. G. Kraige, J. N. Bolton, Engineering Mechanics: Statics, Wiley, 9th edition, 2018.
- S. Timoshenko, D. H. Young, J. V. Rao, S. Pati, Engineering Mechanics (in SI units), McGraw Hill Education (India), 5th edition, 2013.