Indiacon CivilSubscribe

Textbook › Engineering Mechanics › Chapter 4 › Lesson 4.2

4.2 Centroids of lines and areas by integration

Engineering Mechanics Chapter 4: Centroid and centre of gravity Under review — not yet three-checked Author: Indiacon

Learning objectives

After this lesson you should be able to:

  • Set up and evaluate the integrals for the centroid of a line and of a plane area.
  • Derive the centroids of a triangle, a semicircular area, a quarter-circle area, a circular arc and a parabolic spandrel.
  • Choose a strip element that makes the integral simple and check the result by symmetry.

Theory

For shapes with curved or sloping boundaries, the centroid is found by cutting the shape into very small elements, taking the first moment of each about an axis, adding them by integration, and dividing by the total length or area. The whole skill lies in choosing the element. A thin strip parallel to one axis is usually best, because its area is a single expression in one variable and the position of its own centroid is obvious.

For a vertical strip of width dx and height y under a curve, dA = y dx. Its centroid is at distance x from the y axis and at height y/2. So x̄ = ∫x y dx / A and ȳ = ∫(y/2) y dx / A. For a horizontal strip the roles swap. For shapes bounded by circles, a polar element is easier: a thin triangle from the centre of a sector, or a short arc of length r dθ for a wire.

dA = y dxbaC (3a/4, 3b/10)y = k x²x̄ = ∫x dA / AIndiacon original, not to scale
Figure 4.2: A parabolic spandrel cut into vertical strips; integrating their first moments gives the centroid C at (3a/4, 3b/10). Indiacon original, not to scale.

Lines and areas of the same outline have different centroids. A semicircular wire has all its length at radius r, so its centroid is at 2r/π, about 0.637 r from the diameter. A semicircular plate has much of its area near the diameter, so its centroid is closer, at 4r/(3π), about 0.424 r. Keeping this difference clear avoids one of the most common errors in examinations.

The standard results derived here (triangle, semicircle, quarter circle, arc and spandrel) are the building blocks of the composite method in the next lesson. They are worth deriving once and then remembering.

Derivation

  1. Triangle, base b on the x axis, height h: take a horizontal strip at height y. By similar triangles its width is b (h − y)/h, so dA = b (h − y)/h dy.
  2. A = ∫₀ʰ b (h − y)/h dy = b h / 2. First moment ∫ y dA = (b/h) ∫₀ʰ (h y − y²) dy = (b/h)(h³/2 − h³/3) = b h²/6. So ȳ = (b h²/6)/(b h/2) = h/3 from the base.
  3. Circular arc of radius r subtending 2α, symmetric about the x axis: element dL = r dθ at x = r cos θ. L = 2 r α; ∫x dL = ∫₋α^α r² cos θ dθ = 2 r² sin α. So x̄ = r sin α / α. For a semicircular arc (α = π/2), x̄ = 2r/π.
  4. Circular sector of radius r and half-angle α: a thin triangular element from the centre has its centroid at 2r/3 from the centre, so x̄ = (2r/3) sin α / α. For a semicircle (α = π/2), x̄ = 4r/(3π); a quarter circle gives 4r/(3π) from each straight edge.
  5. Parabolic spandrel under y = k x² from x = 0 to a, with height b at x = a (so k = b/a²): A = ∫₀ᵃ k x² dx = a b / 3.
  6. ∫x dA = ∫₀ᵃ k x³ dx = k a⁴/4 = a² b / 4, so x̄ = (a² b/4)/(a b/3) = 3a/4. ∫(y/2) dA = ∫₀ᵃ k² x⁴/2 dx = k² a⁵/10 = a b²/10, so ȳ = (a b²/10)/(a b/3) = 3b/10.
Formulas, symbols and SI units
  • Area: x̄ = ∫x_el dA / A, ȳ = ∫y_el dA / A, where (x_el, y_el) is the centroid of the element
  • Line: x̄ = ∫x dL / L
  • Triangle: h/3 from the base (2h/3 from the apex)
  • Semicircular area: 4r/(3π) from the diameter; semicircular arc: 2r/π
  • Quarter-circle area: 4r/(3π) from each straight edge
  • Circular arc of half-angle α: r sin α / α from the centre; sector: 2r sin α / (3α)
  • Parabolic spandrel (y = kx², 0 ≤ x ≤ a, height b): A = ab/3, x̄ = 3a/4, ȳ = 3b/10
Assumptions and limits
  • Plane, homogeneous plate of uniform thickness (for area) or uniform thin wire (for line).
  • The boundary curve is known as a function that can be integrated; otherwise use the composite or numerical method.
  • Angles in the arc and sector formulae are in radians.

Codes and standards

Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.

  • No design code governs this lesson. The results are used later in section properties of rolled and built-up members and in pressure and load diagrams.

Worked examples

Example 1 (exam style)

Problem. Find the area and centroid of the region under the curve y = x²/8 (x and y in metres) from x = 0 to x = 4 m.

  1. At x = 4, y = 16/8 = 2 m, so a = 4 m and b = 2 m.
  2. A = ∫₀⁴ x²/8 dx = 64/24 = 2.667 m² (= ab/3).
  3. ∫x dA = ∫₀⁴ x³/8 dx = 256/32 = 8 m³, so x̄ = 8 / 2.667 = 3.0 m (= 3a/4).
  4. ∫(y/2) dA = ∫₀⁴ x⁴/128 dx = 1024/640 = 1.6 m³, so ȳ = 1.6 / 2.667 = 0.6 m (= 3b/10).

Answer. A = 2.667 m²; centroid at (3.0 m, 0.6 m)

Example 2 (site style)

Problem. A semicircular arch rib has a centreline radius of 6 m. The rib is of constant section, so its weight is uniform along the arc. Find the height of its centre of gravity above the springing line. Compare it with the centroid of a solid semicircular plate of the same radius.

  1. The rib is a uniform line, so use the arc result with α = π/2: ȳ = 2r/π.
  2. ȳ = 2 × 6 / π = 3.820 m above the springing line.
  3. A solid semicircular plate would have ȳ = 4r/(3π) = 4 × 6 / (3π) = 2.546 m.
  4. The rib centroid is higher because all its material is at the full radius; using the plate value would understate the overturning lever arm of the rib during erection.

Answer. 3.820 m for the rib; 2.546 m for a solid plate

Step-by-step procedure

  1. Sketch the shape and choose axes; mark any axis of symmetry (the centroid lies on it).
  2. Choose a strip or polar element whose area or length is a simple expression.
  3. Write dA (or dL) and the coordinates of the element centroid.
  4. Integrate to get A, ∫x_el dA and ∫y_el dA over the correct limits.
  5. Divide, then check that the result lies inside the outline and is consistent with known results.

Site notes

  • Arch ribs, curved precast units and bent bars are checked for lifting and stability with the line centroid, not the plate centroid, when their section is constant.
  • For irregular plates such as cut-to-shape gusset plates, a scaled drawing in CAD gives the centroid directly; use the integral results as a hand check.
  • Before relying on a computer section property, check the centroid of one simple part by hand. Errors in units or origin are common in input files.
Common mistakes
  • Using 4r/(3π) for a semicircular wire or 2r/π for a semicircular plate.
  • Taking the element centroid at y instead of y/2 for a vertical strip.
  • Using degrees instead of radians in r sin α / α.
  • Measuring the triangle centroid h/3 from the apex instead of from the base.
  • Wrong limits when the strip changes its boundary curve part way across the shape.
Quick check

For a semicircle, the line centroid (0.637 r) is always farther from the diameter than the area centroid (0.424 r). For a triangle, the centroid is one third of the height above any side taken as base.

Summary

  • Centroids of curved shapes come from x̄ = ∫x dA / A with a well-chosen element.
  • Triangle: h/3; semicircular area: 4r/(3π); semicircular arc: 2r/π.
  • Arc: r sin α / α; sector: 2r sin α / (3α).
  • Parabolic spandrel: A = ab/3, x̄ = 3a/4, ȳ = 3b/10.

Practice questions

Tap a question to see the answer.

1Find the distance of the centroid of a quarter-circle area of radius 300 mm from each straight edge.

4r/(3π) = 4 × 300 / (3π) = 127.3 mm.

2Find the distance from the centre to the centroid of a circular arc of radius 2 m that subtends 60° in total.

α = 30° = π/6; x̄ = 2 × sin 30° / (π/6) = 1.910 m.

3Find the centroid of the area enclosed between y = x and y = x² (0 ≤ x ≤ 1).

A = 1/6; x̄ = (1/3 − 1/4)/(1/6) = 0.5; ȳ = ½ (1/3 − 1/5)/(1/6) = 0.4.

4A triangular plate is 900 mm high. How far above its base is the centroid?

h/3 = 300 mm.

5Why is the centroid of a semicircular wire farther from the diameter than that of a semicircular plate?

All of the wire lies at radius r, while much of the plate area lies close to the diameter, which pulls its centroid in: 2r/π = 0.637 r against 4r/(3π) = 0.424 r.

References

Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.

  • F. P. Beer, E. R. Johnston, D. F. Mazurek, P. J. Cornwell, B. P. Self, Vector Mechanics for Engineers: Statics and Dynamics, McGraw Hill, 12th edition, 2019.
  • R. C. Hibbeler, Engineering Mechanics: Statics, Pearson, 15th edition, 2022 (published 2021).
  • J. L. Meriam, L. G. Kraige, J. N. Bolton, Engineering Mechanics: Statics, Wiley, 9th edition, 2018.
  • S. Timoshenko, D. H. Young, J. V. Rao, S. Pati, Engineering Mechanics (in SI units), McGraw Hill Education (India), 5th edition, 2013.
Suggest a correction

If something on this page is wrong, tell the editor. Your message is sent privately and is not published.

Sent privately to the Indiacon editor; not published.