4.1 Centre of gravity, centre of mass and centroid
After this lesson you should be able to:
- Define the centre of gravity, the centre of mass and the centroid, and state when the three coincide.
- Locate the centre of gravity of a system of point weights in two and three dimensions using the first moment.
- Explain why the centre of gravity matters for stability, lifting and load paths on site.
Theory
Every body is made of a very large number of particles, and gravity pulls on each one. These small parallel forces can be replaced by a single resultant, the weight W, acting through one point. That point is the centre of gravity G. Wherever the body is turned, the line of action of its weight passes through G, which is why a body hung from any point comes to rest with G directly below the support.
The centre of mass is defined in the same way, but with mass in place of weight: it is the point at which the whole mass could be concentrated without changing the first moment of mass about any plane. In a uniform gravity field, where g is the same in size and direction at every particle, the centre of gravity and the centre of mass are the same point. For any civil engineering structure the variation of g over its height is far too small to matter, so the two terms are used interchangeably.
The centroid is a purely geometric idea. It is the centre of a line, area or volume, found by weighting each element by its length, area or volume rather than by its weight. If the body is homogeneous (the same density throughout), the centroid of its volume is also its centre of mass and centre of gravity. If the density varies, as in a composite member of steel and concrete or a dam with different zones, the centre of gravity moves towards the heavier part while the centroid stays where the geometry puts it.
The tool behind all of this is the principle of moments from Chapter 1: the moment of the resultant about any axis equals the sum of the moments of the parts. Applied to weights, it gives the centre of gravity; applied to areas, it gives the centroid. The sum of each element times its distance from an axis is called the first moment about that axis. A first moment about an axis through the centroid is always zero, which is a useful check on any calculation.
Derivation
- Let a body consist of particles of weight W1, W2, ..., Wn at points (xi, yi, zi). The resultant weight is W = ΣWi, acting parallel to the individual weights.
- By the principle of moments about the y axis, W x̄ = ΣWi xi, so x̄ = ΣWi xi / ΣWi. In the same way ȳ = ΣWi yi / ΣWi and z̄ = ΣWi zi / ΣWi.
- For a continuous body, replace the sum by an integral over elements of weight dW: x̄ = ∫x dW / ∫dW, and similarly for ȳ and z̄.
- Write dW = g dm. If g is constant it cancels, giving the centre of mass: x̄ = ∫x dm / ∫dm.
- Write dm = ρ dV. If the density ρ is constant it also cancels, giving the centroid of volume: x̄ = ∫x dV / V. For a plate of uniform thickness the same steps give the centroid of area, x̄ = ∫x dA / A; for a uniform thin wire, the centroid of line, x̄ = ∫x dL / L.
- Each cancellation is an assumption: uniform g for centre of gravity = centre of mass, uniform ρ (and thickness) for centre of mass = centroid.
x̄ = ΣWi xi / ΣWi, ȳ = ΣWi yi / ΣWi, z̄ = ΣWi zi / ΣWi (m, with W in N or kN)Continuous body: x̄ = ∫x dW / WCentre of mass: x̄ = ∫x dm / m (m in kg)Centroid of volume, area, line: x̄ = ∫x dV / V, ∫x dA / A, ∫x dL / LFirst moment of area about the y axis: Qy = ∫x dA = A x̄ (m³ or mm³)
- Gravity is uniform and parallel over the body; true to many decimal places for buildings, bridges and machines.
- For the centroid to equal the centre of gravity, the body must be homogeneous; otherwise weight each part by its own unit weight.
- Bodies are rigid: if a load can swing or shift (a hanging load, liquid in a tank, loose material in a truck), the centre of gravity moves and must be checked for the worst position.
Codes and standards
Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.
- No design code governs the mechanics of this lesson; it is pure statics. Codes use its results wherever self-weight is applied through its centre of gravity, for example in stability checks of walls, footings and cranes.
Worked examples
Problem. Three point weights act in a vertical plane: 2 kN at (0, 0), 3 kN at (4, 0) and 5 kN at (4, 3), with coordinates in metres. Find the centre of gravity of the system.
- Total weight W = 2 + 3 + 5 = 10 kN.
- ΣWi xi = 2 × 0 + 3 × 4 + 5 × 4 = 32 kN·m, so x̄ = 32 / 10 = 3.2 m.
- ΣWi yi = 2 × 0 + 3 × 0 + 5 × 3 = 15 kN·m, so ȳ = 15 / 10 = 1.5 m.
- Check: the first moment about the vertical line x = 3.2 m is 2 × (−3.2) + 3 × 0.8 + 5 × 0.8 = −6.4 + 2.4 + 4.0 = 0.
Answer. G at (3.2 m, 1.5 m)
Problem. A mobile crane is idealised along its length with the chassis weight 300 kN at x = 0, the counterweight 80 kN at x = −3 m, the boom 40 kN at x = +4 m and a suspended load of 50 kN at x = +10 m. Find the position of the combined centre of gravity along the crane.
- W = 300 + 80 + 40 + 50 = 470 kN.
- ΣWi xi = 300 × 0 + 80 × (−3) + 40 × 4 + 50 × 10 = 0 − 240 + 160 + 500 = 420 kN·m.
- x̄ = 420 / 470 = 0.894 m ahead of the chassis centre of gravity.
- Without the load, x̄ = (−240 + 160) / 420 = −0.190 m, behind the chassis. Picking up the load moves the combined centre of gravity about 1.08 m forward, towards the front outriggers; this shift is what load charts control.
Answer. x̄ = 0.894 m ahead of the chassis centre of gravity
Step-by-step procedure
- Choose axes, ideally through a corner or a line of symmetry.
- List each part with its weight (or mass, area) and the coordinates of its own centre of gravity.
- Form the sums ΣW, ΣWx, ΣWy (and ΣWz in 3D).
- Divide: x̄ = ΣWx / ΣW and so on.
- Check: the result should lie between the extreme parts and on any axis of symmetry; the first moment about the result should be zero.
Site notes
- Before a lift, the slinging point must be directly above the centre of gravity of the load, or the load will tilt as it leaves the ground. Asymmetric precast units and equipment skids often have their centre of gravity marked by the maker; use the marking rather than guessing.
- A loaded truck, crane or concrete pump is stable only while the combined centre of gravity stays inside the support polygon formed by its wheels or outriggers. Soft ground under one outrigger moves that edge inwards.
- Liquid in a partly filled tank, wet concrete in a mixer drum and loose aggregate in a tipper can shift during movement. The worst position, not the resting one, governs stability.
- Using the geometric centroid for a body made of materials of different density.
- Measuring the coordinates of parts from different origins.
- Forgetting the sign of coordinates on the negative side of the axis (counterweights).
- Dividing the first moment by the number of parts instead of by the total weight.
- Assuming the centre of gravity must lie inside the material; for a ring or an L-shape it lies in empty space.
The centre of gravity always lies within the smallest convex outline of the parts and on every axis of symmetry of a homogeneous body; a result outside these limits is wrong.
Summary
- The centre of gravity is the point through which the resultant weight acts in every orientation.
- In uniform gravity, centre of gravity = centre of mass; for a homogeneous body, both = centroid.
- x̄ = ΣWx / ΣW, and similarly for ȳ and z̄; for continuous bodies use integrals.
- The first moment about an axis through the centroid is zero.
Practice questions
Tap a question to see the answer.
1Masses of 4 kg and 6 kg sit at x = 0 and x = 5 m on a light rod. Where is the centre of mass?
x̄ = (4 × 0 + 6 × 5) / 10 = 3.0 m from the 4 kg mass.
2A 6 m beam weighing 12 kN carries a 4 kN fixture 1.5 m from its left end. Where is the centre of gravity of beam and fixture, measured from the left end?
x̄ = (12 × 3 + 4 × 1.5) / 16 = 42 / 16 = 2.625 m.
3When do the centroid and the centre of gravity of a body coincide?
When the body is homogeneous (uniform density and, for plates, uniform thickness) and gravity is uniform.
4A rod is made of a 1 m steel piece weighing 7.7 N joined end to end with a 1 m aluminium piece weighing 2.65 N. Find its centre of gravity from the steel end and compare it with the centroid.
x̄ = (7.7 × 0.5 + 2.65 × 1.5) / 10.35 = 7.825 / 10.35 = 0.756 m; the centroid of the 2 m length is at 1.0 m, so G lies 0.244 m towards the heavier steel.
5Point weights of 10 N at (0, 0, 0), 20 N at (1, 2, 0) and 30 N at (2, 0, 3), in metres. Find the centre of gravity.
W = 60 N; x̄ = (20 + 60)/60 = 1.333 m, ȳ = 40/60 = 0.667 m, z̄ = 90/60 = 1.5 m.
References
Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.
- F. P. Beer, E. R. Johnston, D. F. Mazurek, P. J. Cornwell, B. P. Self, Vector Mechanics for Engineers: Statics and Dynamics, McGraw Hill, 12th edition, 2019.
- R. C. Hibbeler, Engineering Mechanics: Statics, Pearson, 15th edition, 2022 (published 2021).
- J. L. Meriam, L. G. Kraige, J. N. Bolton, Engineering Mechanics: Statics, Wiley, 9th edition, 2018.
- S. Timoshenko, D. H. Young, J. V. Rao, S. Pati, Engineering Mechanics (in SI units), McGraw Hill Education (India), 5th edition, 2013.