Indiacon CivilSubscribe

Textbook › Engineering Mechanics › Chapter 2 › Lesson 2.5

2.5 Frames and machines

Engineering Mechanics Chapter 2: Analysis of trusses and frames Under review — not yet three-checked Author: Indiacon

Learning objectives

After this lesson you should be able to:

  • Distinguish frames and machines from trusses by identifying multi-force members.
  • Dismember a frame into members, applying equal and opposite pin forces between them.
  • Find pin forces and support reactions, and the mechanical advantage of simple machines.

Theory

A frame is a structure in which at least one member carries forces at more than two points or carries transverse load, so it is a multi-force member and will bend. A machine is a similar assembly with moving parts, designed to change the size or direction of a force: pliers, cutters, levers and toggles. Both are analysed by taking them apart.

First, look for two-force members, such as struts and links pinned at both ends with no load between: their pin forces act along the line joining the pins, which saves unknowns. Then draw each multi-force member separately. At every pin connecting two members, the forces on the two members are equal and opposite (Newton's third law); draw them with opposite arrows and the same symbols.

10 kNABDCstrutBeam AC: multi-force; strut BD: two-forceIndiacon original, not to scale
Figure 2.5: A wall bracket: beam AC is a multi-force member, strut BD a two-force member. Indiacon original, not to scale.

For a frame that is rigid on its own supports, start with the whole structure to find reactions. For a frame that would collapse without its supports (non-rigid frames, such as an A-frame on rollers), the whole-structure equations do not give all reactions, and members must be taken apart before the reactions can be found.

For machines the aim is usually the output force for a given input force. The ratio output ÷ input is the mechanical advantage. For a lever or a pair of pliers pivoting about a pin, moments about the pin give the ratio directly as the ratio of lever arms.

Derivation

  1. Count unknowns: two per internal pin (or one per two-force member) plus the reaction components.
  2. Count equations: three per rigid member in the plane.
  3. A frame is determinate when the number of unknowns equals three times the number of members, and the arrangement is stable.
  4. For a lever with input P at distance a from the pivot and output Q at distance b, ΣM_pivot = 0 gives P a = Q b, so the mechanical advantage is Q/P = a/b.
  5. The pin force is then found from force equilibrium of one member; for parallel P and Q acting on the same side of the pin, it equals P + Q.
Formulas, symbols and SI units
  • Pin forces: equal and opposite on the two connected members
  • Two-force member: force along the line joining its pins
  • Lever: Q = P a / b; mechanical advantage MA = a / b
  • Determinacy of a plane frame: unknowns = 3 × number of rigid members
Assumptions and limits
  • Members are rigid; pins are frictionless.
  • Two-force members are straight, pinned at both ends and unloaded between pins.
  • Machines are analysed statically, at the instant considered, ignoring friction unless stated.

Codes and standards

Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.

  • No design code governs this lesson; it is pure mechanics. Portal frames and brackets designed later to IS 800:2007 or IS 456:2000 begin with exactly this kind of free-body analysis.

Worked examples

Example 1 (exam style)

Problem. A horizontal beam AC, 4 m long, is pinned to a wall at A (0, 0) and propped by a strut BD from B (2 m, 0) on the beam to D (0, −2 m) on the wall. A 10 kN load hangs at C. Find the strut force and the pin reaction at A.

  1. BD is a two-force member at 45°; let it push on the beam with compression C, direction (1, 1)/√2.
  2. Moments about A on the beam: x Fy − y Fx for each force: −4 × 10 + 2 × C/√2 = 0, so C = 20√2 = 28.28 kN (compression).
  3. ΣFx on the beam: Ax + C/√2 = 0, so Ax = −20 kN, i.e. 20 kN acting towards the wall (negative x direction).
  4. ΣFy: Ay + C/√2 − 10 = 0, so Ay = −10 kN (downward).
  5. Resultant at A: √(20² + 10²) = 22.36 kN.

Answer. Strut 28.28 kN compression; pin at A 20 kN horizontal and 10 kN downward (22.36 kN)

Example 2 (site style)

Problem. A hand bar cutter works like pliers. The hand applies 150 N to each handle at 300 mm from the pivot pin; the cutting edges bear on the bar at 25 mm from the pin. Find the cutting force, the mechanical advantage and the pin force.

  1. Moments about the pin on one handle-blade member: 150 × 300 = Q × 25.
  2. Q = 150 × 300 / 25 = 1 800 N.
  3. Mechanical advantage = 300 / 25 = 12.
  4. The hand force and the bar reaction both act on the same side of the pin and in the same direction on that member, so the pin force is 150 + 1 800 = 1 950 N.

Answer. Cutting force 1 800 N; MA = 12; pin force 1 950 N

Step-by-step procedure

  1. Identify two-force members and multi-force members.
  2. If the frame is rigid on its supports, find the reactions from the whole frame.
  3. Dismember: draw each multi-force member with equal and opposite pin forces.
  4. Start with a member that has three or fewer unknowns; take moments about a pin.
  5. Check with an equation not yet used, such as equilibrium of another member.

Site notes

  • Knee braces and props on site are two-force members; the beams or posts they support are multi-force members and will bend at the brace point.
  • The pin force in a lever or cutter is larger than either the input or output force, so the pivot is the part most likely to wear or fail.
  • Temporary works such as raking shores are frames: the shore is a two-force member, but the wall plate and sole plate carry bending and must be checked.
Common mistakes
  • Treating a multi-force member as a two-force member and forcing its pin force along the member.
  • Drawing pin forces in the same direction on both connected members.
  • Including internal pin forces in the free body of the whole frame.
  • Using the whole-frame equations for a non-rigid frame and expecting all reactions.
  • Mixing mm and m in lever arms (harmless in a ratio, but fatal in a moment).
Quick check

If a member carries forces at only two points and no load between, its force runs pin to pin. Everything else bends, and needs its own free body.

Summary

  • Frames and machines contain multi-force members, unlike trusses.
  • Take them apart; pin forces are equal and opposite on connected members.
  • Use two-force members to cut unknowns.
  • Mechanical advantage of a lever = ratio of lever arms.

Practice questions

Tap a question to see the answer.

1A crowbar 1.2 m long pivots 0.1 m from the load end. What force at the handle lifts a 3 kN load end?

P = 3 × 0.1 / 1.1 = 0.273 kN, about 273 N.

2In Example 1, what would the strut force be if the load were at B instead of C?

Moments about A: −2 × 10 + 2C/√2 = 0, so C = 10√2 = 14.14 kN.

3Why can a two-force member not carry bending?

Its two end forces must be collinear along the pin-to-pin line, so it carries only axial force.

4Pliers have handles 120 mm and jaws 20 mm from the pin. A grip of 80 N gives what jaw force?

Q = 80 × 120 / 20 = 480 N.

5How many equations are available for a frame of three rigid members in the plane?

Nine (three per member).

References

Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.

  • F. P. Beer, E. R. Johnston, D. F. Mazurek, P. J. Cornwell, B. P. Self, Vector Mechanics for Engineers: Statics and Dynamics, McGraw Hill, 12th edition, 2019.
  • R. C. Hibbeler, Engineering Mechanics: Statics, Pearson, 15th edition, 2022 (published 2021).
  • J. L. Meriam, L. G. Kraige, J. N. Bolton, Engineering Mechanics: Statics, Wiley, 9th edition, 2018.
  • S. Timoshenko, D. H. Young, J. V. Rao, S. Pati, Engineering Mechanics (in SI units), McGraw Hill Education (India), 5th edition, 2013.
Suggest a correction

If something on this page is wrong, tell the editor. Your message is sent privately and is not published.

Sent privately to the Indiacon editor; not published.