Indiacon CivilSubscribe

Textbook › Engineering Mechanics › Chapter 2 › Lesson 2.3

2.3 Method of sections

Engineering Mechanics Chapter 2: Analysis of trusses and frames Under review — not yet three-checked Author: Indiacon

Learning objectives

After this lesson you should be able to:

  • Cut a truss into two parts and find up to three member forces from one free body.
  • Choose moment centres that eliminate two unknowns at a time.
  • Estimate chord forces of a parallel-chord truss from the beam bending moment, and diagonal forces from the beam shear.

Theory

The method of sections finds the force in a chosen member directly, without working through every joint. We pass an imaginary cut through the truss so that it crosses the member we want and no more than three members with unknown forces in total, then draw the free body of the part on one side of the cut. The cut members are replaced by their axial forces, drawn as tension.

Because the part is a rigid body, it has three equilibrium equations. The skill is in choosing them. Taking moments about the point where two of the cut members meet eliminates both and gives the third directly. For a parallel-chord truss, moments about a bottom joint give the top chord force; moments about a top joint give the bottom chord force; and vertical force balance gives the diagonal force from the shear in that panel.

cutSection through U1–U2, U1–L2, L1–L2Indiacon original, not to scale
Figure 2.3: A section cutting three members of the truss; the left part is solved as a rigid body. Indiacon original, not to scale.

This leads to a powerful analogy. A parallel-chord truss behaves like a beam whose flanges are the chords and whose web is the diagonals and verticals. At any section, chord force ≈ bending moment ÷ truss depth, and the vertical component of the diagonal force equals the shear force in that panel. The analogy explains why chord forces are largest at midspan and diagonal forces largest near the supports.

The method of sections is the tool of choice when only a few member forces are needed, such as checking the most heavily loaded chord, and it is also the basis of influence-line analysis of bridge trusses, where the force in one member is tracked as a load moves across.

Derivation

  1. Cut the truss into a left part and a right part through three members whose lines are not all concurrent or parallel.
  2. The left part is in equilibrium under the reactions and loads on it and the three member forces, so ΣFx = 0, ΣFy = 0 and ΣM = 0 hold for it.
  3. Take moments about the intersection of the lines of two cut members: those two forces have zero moment, so the equation contains only the third force.
  4. For a parallel-chord truss of depth h, moments about the bottom joint at the section give F_top × h + M = 0, where M is the beam bending moment there (sagging positive), so F_top = −M/h (compression); similarly F_bottom = +M/h (tension).
  5. Vertical equilibrium of the left part gives the vertical component of the diagonal force equal to the beam shear V in that panel: F_diag × sin θ = ±V, the sign depending on the direction of the diagonal.
Formulas, symbols and SI units
  • F_chord = M / h (top chord compression, bottom chord tension for sagging M)
  • F_diag sin θ = V (shear in the panel)
  • Simply supported, uniform load w over span L: M_max = w L² / 8 at midspan
  • Moment centre for a chord = joint where the other two cut members meet
Assumptions and limits
  • Ideal truss, determinate and stable.
  • The cut crosses no more than three members with unknown forces (more are allowed only if all but three are already known).
  • For the beam analogy, chords are parallel and loads act at panel points.

Codes and standards

Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.

  • IS 800:2007 governs design of the members whose forces are found here; the analysis method is pure mechanics. Bridge trusses for Indian Railways and roads are loaded to their own bridge rules and IRC codes, which govern loads, not this method.

Worked examples

Example 1 (exam style)

Problem. The truss of lesson 2.1 (bottom joints L0 to L4 at 3 m spacing, top joints U1 to U3 at 3 m height, diagonals U1–L2 and U3–L2) carries 10 kN at each of L1, L2 and L3. Find the forces in U1–U2, L1–L2 and U1–L2.

  1. Reactions: total load 30 kN, symmetric, so 15 kN at each support.
  2. Cut through U1–U2, U1–L2 and L1–L2 and keep the left part.
  3. Moments about L2 (6, 0): −15 × 6 + 10 × 3 − 3 F_U1U2 = 0, so F_U1U2 = −20 kN (compression).
  4. Moments about U1 (3, 3): −15 × 3 + 3 F_L1L2 = 0, so F_L1L2 = +15 kN (tension).
  5. ΣFy on the left part: 15 − 10 − F_U1L2 / √2 = 0, so F_U1L2 = 5√2 = 7.071 kN (tension).

Answer. U1–U2 = 20 kN C; L1–L2 = 15 kN T; U1–L2 = 7.071 kN T

Example 2 (site style)

Problem. A temporary steel truss footbridge spans 30 m with parallel chords 4 m apart. The design load, including self-weight, is equivalent to 20 kN/m along the span. Estimate the maximum chord force for a first sizing.

  1. Treat the truss as a simply supported beam: M_max = w L² / 8 = 20 × 30² / 8 = 2 250 kN·m at midspan.
  2. Chord force ≈ M / h = 2 250 / 4 = 562.5 kN.
  3. Top chord about 562.5 kN compression, bottom chord about 562.5 kN tension at midspan.
  4. The maximum shear is at the support, w L / 2 = 300 kN, which governs the end diagonals.

Answer. About 562.5 kN in each chord at midspan (top compression, bottom tension)

Step-by-step procedure

  1. Find the reactions from the whole truss.
  2. Choose a cut through the target member and at most two other unknown members.
  3. Draw the simpler side as a free body, with cut-member forces as tension.
  4. Take moments about the intersection of two unknowns to get the third; repeat with other centres or use ΣFy.
  5. Check one result by the method of joints or the beam analogy.

Site notes

  • For a quick check of a truss design, compare the chord forces in the calculation with M/h. A large mismatch means a loading or geometry error.
  • Making a truss deeper reduces chord forces in direct proportion; span-to-depth ratios are chosen to balance chord size, diagonal length and clearance.
  • Near the supports the diagonals carry the largest forces because shear is largest there; check the end diagonals and their connections carefully.
Common mistakes
  • Cutting through four unknown members and trying to solve them with three equations.
  • Forgetting the loads on the free body that lie on the chosen side of the cut.
  • Taking moments about a point and forgetting the reaction.
  • Mixing up which chord is in compression: for a sagging moment, the top chord is compressed.
  • Using the full shear for a diagonal without dividing by sin θ.
Quick check

Chord force ≈ moment ÷ depth; diagonal force ≈ shear ÷ sine of its angle. For a 45° diagonal, the force is √2 = 1.414 times the panel shear.

Summary

  • Cut through at most three unknown members and use the three equilibrium equations of one part.
  • Moments about the meeting point of two members give the third force directly.
  • Chord force ≈ M / h; diagonal vertical component = panel shear.
  • Use sections for selected members and for influence lines.

Practice questions

Tap a question to see the answer.

1In Example 1, find the force in L0–U1.

At L0: 15 + F/√2 = 0, so F = −21.21 kN (compression).

2In Example 1, find the force in L0–L1.

At L0: F_L0L1 + (−21.21)/√2 = 0, so F_L0L1 = 15 kN tension.

3A parallel-chord truss of depth 2.5 m has a bending moment of 500 kN·m at a section. Estimate the chord forces.

500 / 2.5 = 200 kN: top chord compression, bottom chord tension.

4A panel shear is 40 kN and the diagonal is at 60° to the horizontal. Find the diagonal force.

F = 40 / sin 60° = 46.19 kN.

5If the footbridge of Example 2 were made 5 m deep, what would the chord force become?

2 250 / 5 = 450 kN.

References

Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.

  • F. P. Beer, E. R. Johnston, D. F. Mazurek, P. J. Cornwell, B. P. Self, Vector Mechanics for Engineers: Statics and Dynamics, McGraw Hill, 12th edition, 2019.
  • R. C. Hibbeler, Engineering Mechanics: Statics, Pearson, 15th edition, 2022 (published 2021).
  • J. L. Meriam, L. G. Kraige, J. N. Bolton, Engineering Mechanics: Statics, Wiley, 9th edition, 2018.
  • S. Timoshenko, D. H. Young, J. V. Rao, S. Pati, Engineering Mechanics (in SI units), McGraw Hill Education (India), 5th edition, 2013.
Suggest a correction

If something on this page is wrong, tell the editor. Your message is sent privately and is not published.

Sent privately to the Indiacon editor; not published.