2.2 Method of joints
After this lesson you should be able to:
- Find support reactions of a truss from equilibrium of the whole structure.
- Find every member force by joint equilibrium, with a consistent tension-positive sign convention.
- Choose the order of joints so that no joint has more than two unknowns.
Theory
The method of joints treats each pin of a truss as a particle in equilibrium. Because every member is a two-force member, the force it exerts on a joint acts along the member. If we draw each unknown member force as a pull away from the joint (tension positive), a negative answer means the member is in compression. This one convention removes most sign errors.
Each joint gives two equations, so we start at a joint with at most two unknown member forces, usually a support joint once the reactions are known. Solving that joint gives forces in its members, which become known values at the joints at their other ends. We move from joint to joint, always choosing one with no more than two unknowns, until every member is solved. Any equations left over at the end are free checks.
Resolving inclined member forces is easiest with the member geometry rather than angles. If a member rises 3 m over a horizontal run of 2 m, its length is √13 m and its force has components F × 2/√13 horizontally and F × 3/√13 vertically. Keeping the exact ratios until the end avoids rounding drift through a long chain of joints.
The method of joints gives all member forces and is the natural method when a full force table is needed, for example for design of every member. Its weakness is that an error at an early joint is carried through every later one, so checks at the last joints matter.
Derivation
- Free body of the whole truss: three equations (ΣFx = 0, ΣFy = 0, ΣM = 0) give the three reactions of a determinate truss with a pin and a roller.
- Free body of joint i: the forces are the external load at i, any reaction at i, and the member forces Fij directed from i towards j (assumed tension).
- With unit vector eij from joint i to joint j, equilibrium is Σ Fij eij + Pi = 0, which gives two scalar equations.
- Writing eij = (xj − xi, yj − yi) / Lij keeps signs automatic: a positive Fij is tension, a negative Fij compression.
- Collecting the equations of all joints gives a linear system with 2j equations and m + r unknowns; for a determinate truss it has a unique solution, which the joint-by-joint method finds by hand.
Joint equilibrium: ΣFx = 0, ΣFy = 0 at every jointMember force components: Fx = F (xj − xi) / L, Fy = F (yj − yi) / LMember length: L = √((xj − xi)² + (yj − yi)²)Sign: F > 0 tension, F < 0 compression (kN)
- Ideal truss assumptions from lesson 2.1: pins, joint loads, two-force members, small deflections.
- Statically determinate truss (m + r = 2j and stable).
- Tension positive, member forces drawn pulling away from the joint.
Codes and standards
Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.
- IS 800:2007 is used to design the members once forces are known: tension members by Section 6 and compression members by Section 7. EN 1993-1-1 and AISC 360 cover the same tasks elsewhere; they are listed for comparison, not ranked.
Worked examples
Problem. A triangular truss has supports A (pin) at (0, 0) and B (roller) at (6 m, 0) and apex C at (3 m, 4 m). A 30 kN load acts downward at C. Find the forces in all three members.
- By symmetry, the vertical reactions are Ay = By = 15 kN; Ax = 0.
- Member AC has length 5 m; unit vector from A to C is (0.6, 0.8).
- Joint A, ΣFy: 15 + 0.8 F_AC = 0, so F_AC = −18.75 kN (compression).
- Joint A, ΣFx: F_AB + 0.6 F_AC = 0, so F_AB = 11.25 kN (tension).
- By symmetry F_BC = −18.75 kN. Check at C: vertical components 2 × 0.8 × 18.75 = 30 kN, equal to the load.
Answer. AC = BC = 18.75 kN compression; AB = 11.25 kN tension
Problem. A small Warren truss for a walkway has bottom joints A (0, 0), B (4, 0), C (8, 0) and top joints D (2, 3), E (6, 3), in metres; members AB, BC, AD, DB, BE, EC and DE. A is pinned, C is on a roller and a 20 kN load acts down at B. Find all member forces.
- Reactions: by symmetry Ay = Cy = 10 kN.
- Diagonals have length √(2² + 3²) = √13 = 3.606 m.
- Joint A: ΣFy: 10 + F_AD × 3/√13 = 0, so F_AD = −12.02 kN. ΣFx: F_AB + F_AD × 2/√13 = 0, so F_AB = +6.667 kN.
- Joint D: ΣFy: −3F_AD/√13 − 3F_DB/√13 = 0, so F_DB = +12.02 kN. ΣFx: −2F_AD/√13 + 2F_DB/√13 + F_DE = 0, so F_DE = −13.33 kN.
- By symmetry F_BE = +12.02 kN, F_EC = −12.02 kN, F_BC = +6.667 kN. Check at B: vertical components 2 × 12.02 × 3/√13 = 20.0 kN, equal to the load.
Answer. AD = EC = 12.02 kN C; DB = BE = 12.02 kN T; DE = 13.33 kN C; AB = BC = 6.667 kN T
Step-by-step procedure
- Check determinacy and stability.
- Find the reactions from the whole truss.
- Start at a joint with at most two unknowns; draw unknown forces as tension.
- Resolve with geometry ratios, solve, and record each force with T or C.
- Move to the next joint with at most two unknowns; use the leftover equations as checks.
Site notes
- Compression members (struts) govern the section size because of buckling; tension members (ties) can be slender rods or flats, subject to the slenderness limits of the design code.
- When a truss is lifted by crane at points other than its supports, member forces can reverse; a tie may become a strut during erection. Check the lifting case.
- Mark member forces as T or C on erection drawings so site teams do not swap similar-looking members.
- Drawing some unknown forces into the joint and others away from it, then misreading the signs.
- Rounding diagonal components early so the final check fails by a few per cent.
- Starting at a joint with three unknowns.
- Forgetting to include the reaction at a support joint.
- Reporting a negative value without saying it means compression.
At an unloaded joint where only two non-collinear members meet, both forces are zero; at a support joint with one inclined member, that member carries the vertical reaction divided by the sine of its angle. Quick checks like these catch most slips.
Summary
- Each joint is a particle: ΣFx = 0 and ΣFy = 0.
- Draw unknown member forces as tension; negative means compression.
- Solve reactions first, then joints with no more than two unknowns.
- Use leftover joint equations as checks.
Practice questions
Tap a question to see the answer.
1In Example 1, what would F_AB be if the apex were 3 m high instead of 4 m?
AC length √18; F_AC = −15 √18 / 3 = −21.21 kN; F_AB = 21.21 × 3/√18 = 15 kN tension.
2A joint has a 10 kN downward load and two members at 45° on either side going up to the left and up to the right. Find the member forces.
Each vertical component is 5 kN, so each force is 5/sin 45° = 7.071 kN, in tension (the members hold the load up).
3In Example 2, find the horizontal reaction at A.
Zero: no horizontal load acts on the truss.
4A member from (0, 0) to (4, 3) m carries 25 kN tension. Find its force components on the joint at (0, 0).
Unit vector (0.8, 0.6): components 20 kN and 15 kN towards (4, 3).
5Why do symmetric trusses under symmetric loads have equal forces in mirror-image members?
The equilibrium equations for the mirror half are identical, so mirror members must carry equal forces of the same sign.
References
Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.
- F. P. Beer, E. R. Johnston, D. F. Mazurek, P. J. Cornwell, B. P. Self, Vector Mechanics for Engineers: Statics and Dynamics, McGraw Hill, 12th edition, 2019.
- R. C. Hibbeler, Engineering Mechanics: Statics, Pearson, 15th edition, 2022 (published 2021).
- J. L. Meriam, L. G. Kraige, J. N. Bolton, Engineering Mechanics: Statics, Wiley, 9th edition, 2018.
- S. Timoshenko, D. H. Young, J. V. Rao, S. Pati, Engineering Mechanics (in SI units), McGraw Hill Education (India), 5th edition, 2013.