2.1 Plane trusses: assumptions and determinacy
After this lesson you should be able to:
- List the assumptions that turn a real truss into an ideal pin-jointed plane truss and judge when they are acceptable.
- Classify a plane truss as statically determinate, indeterminate or unstable using m + r and 2j, and separate external from internal indeterminacy.
- Recognise simple, compound and complex trusses and explain why triangles give stability.
Theory
A truss is a structure made of straight, slender members joined at their ends so that, under loads applied at the joints, each member carries only an axial force: tension or compression. Roof trusses over factories and stations, the side girders of many railway and road bridges, transmission towers and tower-crane jibs are all trusses. Because axial force uses the whole cross-section uniformly, a truss carries large loads over long spans with very little material.
To analyse a truss by hand we replace it with an ideal truss. Members are straight and meet at frictionless pins; loads and reactions act only at the joints; member self-weight is either ignored or split equally between the two end joints; and the members are rigid for the purpose of finding forces. Under these assumptions every member is a two-force member: the only forces on it are at its two ends, so they must be equal, opposite and along the line joining the pins.
The basic stable unit is the triangle. Three bars pinned in a triangle cannot change shape without a bar changing length, whereas four bars pinned in a rectangle fold into a parallelogram. A simple truss is built from a triangle by adding two new members and one new joint at a time; it always satisfies m = 2j − 3 and is internally stable. A compound truss joins two simple trusses by three non-concurrent, non-parallel connections. Trusses that are neither are complex and need more general methods.
Each joint of a plane truss is a particle in equilibrium, giving two equations (ΣFx = 0, ΣFy = 0). With j joints there are 2j equations; the unknowns are the m member forces and the r reaction components. If m + r = 2j the truss may be statically determinate; if m + r > 2j it is statically indeterminate to degree m + r − 2j; if m + r < 2j it is a mechanism. The count is necessary but not sufficient: a truss with the right count can still be unstable if its members or reactions are badly arranged, for example if all three reactions are parallel or concurrent.
Derivation
- Take any member AB of an ideal truss. Only two forces act on it, one at A and one at B, because loads act only at joints and self-weight is ignored or lumped at the joints.
- For equilibrium of the member, ΣF = 0 makes the two forces equal and opposite; ΣM_A = 0 then makes the force at B pass through A. So both forces lie along AB: the member force is purely axial.
- Each of the j joints is a concurrent force system in the plane, so it supplies exactly two independent equilibrium equations: 2j equations in total.
- The unknowns are one axial force per member (m) and the reaction components (r). Determinacy needs as many independent equations as unknowns: m + r = 2j.
- Split the count: external indeterminacy = r − 3 (a plane rigid body has three equilibrium equations); internal indeterminacy = m − (2j − 3). Their sum is m + r − 2j.
Plane truss degree of indeterminacy: D = m + r − 2j (D = 0 determinate if stable, D > 0 indeterminate, D < 0 mechanism)Simple truss: m = 2j − 3 (internally determinate)External indeterminacy De = r − 3; internal indeterminacy Di = m − (2j − 3)Axial stress in a member: σ = F / A (N/mm² when F in N and A in mm²)Self-weight of a member of length Lm and weight w per metre: w Lm, half to each end joint (kN)
- Joints behave as frictionless pins. Real bolted or welded gusset joints transfer some moment, which causes secondary bending stresses; these are usually small when members are slender and their centroidal axes meet at a point.
- Loads act at joints. Purlins in roof trusses are placed over panel points for this reason; a load between joints causes bending in that member.
- Members are straight and their centroidal axes meet at the joint.
- Small deflections: the geometry used for equilibrium is the unloaded geometry.
Codes and standards
Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.
- IS 800:2007 governs the design of steel truss members in India; cl. 3.8 with Table 3 sets maximum effective slenderness ratios (for example 180 for members carrying compression from dead and imposed loads, 400 for members always in tension). EN 1993-1-1 and AISC 360 are the comparable steel design standards elsewhere; they are listed for comparison, not ranked.
- Wind loads on roof trusses in India come from IS 875 (Part 3):2015; this lesson only covers the mechanics.
Worked examples
Problem. A bridge truss has a bottom chord of four 3 m panels (joints L0 to L4), top chord joints U1, U2, U3 at 3 m height, end diagonals L0–U1 and U3–L4, verticals at U1, U2, U3 and diagonals U1–L2 and U3–L2. It is pinned at L0 and on a roller at L4. Classify it.
- Joints: L0, L1, L2, L3, L4, U1, U2, U3, so j = 8.
- Members: 4 bottom chord + 2 top chord + 2 end diagonals + 3 verticals + 2 diagonals = 13.
- Reactions: pin 2 + roller 1, so r = 3.
- m + r = 16 = 2j = 16, and the truss is built from triangles with reactions neither parallel nor concurrent, so it is stable and statically determinate. De = 0, Di = 13 − 13 = 0.
Answer. Statically determinate and stable (D = 0)
Problem. A 9 m roof truss is modified on site: both ends are bolted down as pins, and an extra diagonal is added in one panel. Before the change it had j = 8, m = 13 and a pin plus a roller. Find the new degree of indeterminacy and say what it means.
- After the change, m = 14 and r = 2 + 2 = 4.
- D = m + r − 2j = 14 + 4 − 16 = 2.
- De = r − 3 = 1 (the second pin); Di = 14 − 13 = 1 (the extra diagonal).
- The truss is now indeterminate to degree 2: member forces depend on member stiffness and on temperature, and the method of joints alone cannot find them.
Answer. Indeterminate to degree 2 (one external, one internal)
Step-by-step procedure
- Count joints j, members m and reaction components r (pin 2, roller 1, fixed support 3).
- Compute D = m + r − 2j.
- Split into De = r − 3 and Di = m − (2j − 3).
- Check the arrangement: every panel triangulated, reactions not all parallel or concurrent.
- State the classification and, if determinate, proceed to joints or sections.
Site notes
- Place purlins over panel points. A purlin between nodes puts bending into the top chord, which the ideal-truss analysis does not see.
- A truss that is pinned at both ends is externally indeterminate; temperature change then produces axial force. Long-span trusses are given one sliding bearing for this reason.
- Gusset plates should be detailed so that member centroidal axes meet at a point; offsets create secondary moments.
- Counting a pin support as one reaction instead of two.
- Assuming m + r = 2j guarantees stability; a rectangle panel without a diagonal can satisfy the count elsewhere and still collapse.
- Forgetting that a member between joints with a load on it is no longer a two-force member.
- Counting a joint twice where three or more members meet.
- Using the space-truss rule 3j for a plane truss.
A simple plane truss always has m = 2j − 3. With a pin and a roller (r = 3), m + r = 2j exactly. If your count gives more, look for an extra member or support; if fewer, look for an untriangulated panel.
Summary
- An ideal truss has pin joints, joint loads and two-force members carrying only axial force.
- Triangles make a truss stable; simple trusses satisfy m = 2j − 3.
- D = m + r − 2j, split into De = r − 3 and Di = m − (2j − 3).
- The count is necessary, not sufficient: check the geometry too.
Practice questions
Tap a question to see the answer.
1A plane truss has 5 joints, 7 members, a pin and a roller. Classify it.
m + r = 7 + 3 = 10 = 2j, so it is determinate if stably arranged.
2A square of four members with a pin and a roller: classify it.
m + r = 4 + 3 = 7 < 2j = 8, so it is a mechanism (the square folds).
3A truss has j = 6, m = 10, r = 3. Find D.
D = 10 + 3 − 12 = 1, indeterminate to degree 1 (internally).
4A 4 m member weighs 0.15 kN/m. What load does its self-weight add to each end joint?
Total 0.6 kN; 0.3 kN at each end joint.
5A truss member carries 120 kN tension and has an area of 1 500 mm². Find its axial stress.
σ = 120 000 / 1 500 = 80 N/mm².
6Why does a roller at one end make a long truss less sensitive to temperature change?
It removes the second horizontal restraint, so the truss can expand freely and no axial force is induced; De drops from 1 to 0.
References
Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.
- F. P. Beer, E. R. Johnston, D. F. Mazurek, P. J. Cornwell, B. P. Self, Vector Mechanics for Engineers: Statics and Dynamics, McGraw Hill, 12th edition, 2019.
- R. C. Hibbeler, Engineering Mechanics: Statics, Pearson, 15th edition, 2022 (published 2021).
- J. L. Meriam, L. G. Kraige, J. N. Bolton, Engineering Mechanics: Statics, Wiley, 9th edition, 2018.
- S. Timoshenko, D. H. Young, J. V. Rao, S. Pati, Engineering Mechanics (in SI units), McGraw Hill Education (India), 5th edition, 2013.