Indiacon CivilSubscribe

Textbook › Engineering Mechanics › Chapter 9 › Lesson 9.4

9.4 Energy methods for rigid bodies

Engineering Mechanics Chapter 9: Plane motion of rigid bodies Under review — not yet three-checked Author: Indiacon

Learning objectives

After this lesson you should be able to:

  • Write the kinetic energy of a rigid body in plane motion, T = ½ m v_G² + ½ I_G ω², and the fixed-axis form T = ½ I_O ω².
  • Apply the work-energy principle and conservation of energy to rolling bodies, hoist drums and falling bars, including the work of a couple, U = M θ.
  • Use power P = M ω for rotating machines and the energy stored in a flywheel.

Theory

The work-energy principle of lesson 8.2, U(1→2) = T₂ − T₁, holds for a rigid body too, provided the kinetic energy includes rotation. Adding up ½ v² dm over the body gives T = ½ m v_G² + ½ I_G ω²: the energy of the mass centre's motion plus the energy of spinning about it. For rotation about a fixed axis O this becomes T = ½ I_O ω², and for rolling without slip it can also be written ½ I_C ω² about the contact point C.

Forces do work as before: weight does m g h, springs ½ k (x₁² − x₂²), friction at a sliding contact −μ N s. A couple M turning a body through an angle θ does work U = ∫ M dθ, or M θ if M is constant. Two forces do no work in rigid-body problems that often trip students: the internal forces between particles of a rigid body (their points do not move relative to each other), and the friction force at the contact of a wheel rolling without slip (its point of application has zero velocity).

pin O1: horizontal, ω = 0G2: verticalv = ω Ldrop L/2m g L/2 = ½ I_O ω²Indiacon original, not to scale
Figure 9.4: Energy method for a hinged beam: the mass centre drops L/2, and that potential energy becomes rotational kinetic energy ½ I_O ω² about the pin. Indiacon original, not to scale.

Energy methods give speeds directly from positions, without accelerations or time. They are especially convenient for connected systems, such as a load hanging from a drum, because the internal rope tension does no net work on the system and drops out. When only conservative forces work, T₁ + V₁ = T₂ + V₂. A body that rolls shares its energy between translation and rotation, so it reaches the bottom of a slope more slowly than a frictionless sliding block from the same height.

Power for a rotating shaft is P = M ω, in watts. A flywheel stores energy ½ I ω²; when the speed falls from ω₁ to ω₂ it gives out ½ I (ω₁² − ω₂²). This is how crushers, presses and pile hammers ride through peak loads with a smaller motor, and it is also the energy that a brake must absorb as heat to stop a drum, a rotor or a wheel.

Derivation

  1. Kinetic energy of the body: T = ½ ∫ v² dm, with v = v_G + ω × ρ for a particle at ρ from G.
  2. v² = v_G² + 2 v_G · (ω × ρ) + ω² ρ² in plane motion.
  3. ∫ ρ dm = 0 by definition of G, so the middle term vanishes: T = ½ m v_G² + ½ ω² ∫ ρ² dm = ½ m v_G² + ½ I_G ω².
  4. Fixed axis O: v_G = ω d, so T = ½ (m d² + I_G) ω² = ½ I_O ω².
  5. Rolling without slip: v_G = r ω, so T = ½ m v_G² (1 + k²/r²).
  6. Work of a couple: dU = M dθ, so U = ∫ M dθ = M θ for constant M; power P = dU/dt = M ω.
  7. Rolling from rest through a height h, energy conserved: m g h = ½ m v² (1 + k²/r²), so v = √(2 g h / (1 + k²/r²)).
  8. Uniform bar falling about one end from horizontal to vertical: m g L/2 = ½ (m L²/3) ω², so ω = √(3 g / L).
Formulas, symbols and SI units
  • T = ½ m v_G² + ½ I_G ω² (J)
  • Fixed axis: T = ½ I_O ω²; rolling: T = ½ m v_G² (1 + k²/r²)
  • Work of a couple U = M θ (J, θ in radians)
  • Power P = M ω (W); ω = 2π N / 60
  • Conservation: T₁ + V₁ = T₂ + V₂ with V_g = m g h, V_e = ½ k x²
  • Rolling from rest through height h: v = √(2 g h / (1 + k²/r²))
  • Flywheel energy change ΔT = ½ I (ω₁² − ω₂²)
Assumptions and limits
  • The body is rigid and in plane motion.
  • Rolling is without slip, so the contact friction does no work; any slip adds a negative work term.
  • Bearing friction and air resistance are neglected unless stated.
  • The energy method gives speeds and angular speeds, not times or reactions; use the equations of lesson 9.3 for forces.

Codes and standards

Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.

  • No design code governs this lesson; energy methods for rigid bodies are a part of mechanics. Brake capacity, flywheel and motor ratings follow the machine and equipment standards of the relevant subjects, not this lesson.

Worked examples

Example 1 (exam style)

Problem. A solid cylindrical roller rolls from rest without slipping down a slope through a vertical drop of 2 m. Find its speed at the bottom, compare it with a block sliding without friction through the same drop, and find how the energy is shared.

  1. Solid cylinder k²/r² = ½, so m g h = ½ m v² (1 + ½) = ¾ m v².
  2. v = √(4 g h / 3) = √(4 × 9.81 × 2 / 3) = 5.115 m/s.
  3. Frictionless block: v = √(2 g h) = √(39.24) = 6.264 m/s.
  4. Share: translation ½ m v² is (1 / 1.5) = 2/3 of the energy; rotation is 1/3.

Answer. Roller 5.11 m/s against 6.26 m/s for a sliding block; 2/3 translation, 1/3 rotation

Example 2 (site style)

Problem. For the winch of lesson 9.3 Example 1 (drum I = 18 kg·m², rope radius 0.4 m, hanging load 100 kg), the brake is released with the load at rest. Find the load's speed after it has dropped 2 m, and check the result against the acceleration found earlier.

  1. Take drum + rope + load as one system; the rope tension is internal and does no net work.
  2. Work of gravity = 100 × 9.81 × 2 = 1962 J.
  3. T₂ = ½ × 100 × v² + ½ × 18 × (v / 0.4)² = (50 + 56.25) v² = 106.25 v².
  4. v² = 1962 / 106.25 = 18.466, so v = 4.297 m/s; drum ω = 4.297 / 0.4 = 10.74 rad/s.
  5. Check: v² = 2 a s = 2 × 4.6165 × 2 = 18.466. Same answer, found without the rope tension.

Answer. v = 4.30 m/s; drum 10.7 rad/s

Example 3 (site style)

Problem. The 6 m, 300 kg uniform beam of lesson 9.3 Example 3 swings down about its pin after the prop is knocked out. Find its angular velocity and the speed of the free end when it hangs vertically, and the pin reaction at that instant.

  1. Loss of potential energy: m g L/2 = 300 × 9.81 × 3 = 8829 J.
  2. ½ I_O ω² = ½ × 3600 × ω² = 8829, so ω² = 4.905 and ω = 2.215 rad/s (= √(3g/L)).
  3. Free-end speed v = ω L = 2.215 × 6 = 13.29 m/s, more than the 10.85 m/s of an object falling freely through 6 m.
  4. At the vertical the moment of the weight about the pin is zero, so α = 0; a_G is centripetal: ω² L/2 = 4.905 × 3 = 14.715 m/s² upwards.
  5. Pin reaction R = m g + m ω² L/2 = 300 × (9.81 + 14.715) = 7357.5 N, which is 2.5 times the weight.

Answer. ω = 2.21 rad/s; free end 13.3 m/s; pin reaction 7.36 kN (2.5 m g)

Step-by-step procedure

  1. Choose positions 1 and 2 and the system (often several connected bodies together, so internal forces drop out).
  2. Write the kinetic energy of each body: ½ m v_G² + ½ I_G ω², or ½ I_O ω² for a fixed axis.
  3. Link the speeds by kinematics (v = r ω for ropes and rolling) so that one unknown speed remains.
  4. Find the work of external forces and couples (or the change in potential energy), remembering forces that do no work.
  5. Solve U(1→2) = T₂ − T₁ (or T₁ + V₁ = T₂ + V₂); then use the equations of motion if forces or reactions are needed.

Site notes

  • A falling or swinging element picks up energy fast: Example 3 shows a hinged beam's free end hitting harder than a free-falling object and the pin seeing 2.5 times the weight, so hinged panels and beams are lowered on slings, never dropped.
  • The energy a brake must absorb includes the rotating parts: ½ I ω² of drums, gears and motor rotors can be a large share for a light load on a heavy winch.
  • Crushers, presses and pile hammers use flywheels: a 20 kg·m² flywheel slowing from 300 to 200 rev/min releases about 5.5 kJ to break a stone or drive a blow.
  • Motor sizing uses P = M ω: a winch drum needing 150 N·m at 1450 rev/min draws about 22.8 kW at the shaft before losses.
Common mistakes
  • Leaving out the rotational energy ½ I_G ω² of wheels, drums or pulleys.
  • Counting rope tension as external work when the drum and the load are taken as one system.
  • Using degrees in U = M θ.
  • Including friction work at the contact of a wheel that rolls without slipping.
  • Trying to find a reaction or a time from the energy equation alone.
Quick check

Speed at the bottom of a slope from rest: ring √(g h), solid cylinder √(4 g h / 3), frictionless block √(2 g h).

Summary

  • T = ½ m v_G² + ½ I_G ω²; fixed axis ½ I_O ω².
  • Couple work M θ; power M ω.
  • Rolling: v = √(2 g h / (1 + k²/r²)).
  • Flywheel energy change ½ I (ω₁² − ω₂²).

Practice questions

Tap a question to see the answer.

1Find the kinetic energy of a flywheel with I = 20 kg·m² running at 300 rev/min.

ω = 31.416 rad/s; T = ½ × 20 × 31.416² = 9870 J.

2How much energy does that flywheel give out when it slows to 200 rev/min?

ω₂ = 20.944 rad/s; ΔT = ½ × 20 × (31.416² − 20.944²) = 5483 J.

3A motor delivers 150 N·m at 1450 rev/min. Find the power.

ω = 151.84 rad/s; P = 150 × 151.84 = 22 777 W = 22.8 kW.

4A thin ring and a solid disc each roll from rest down through a height of 1 m. Find their speeds.

Ring v = √(g h) = 3.132 m/s; disc v = √(4 g h / 3) = 3.617 m/s.

5Find the work done by a constant couple of 50 N·m turning a shaft through 10 revolutions.

U = 50 × 20π = 3141.6 J.

6A 20 kg wheel of radius 0.4 m and radius of gyration 0.3 m rolls without slip at 3 m/s. Find its kinetic energy.

ω = 7.5 rad/s; T = ½ × 20 × 9 + ½ × 20 × 0.09 × 56.25 = 90 + 50.6 = 140.6 J.

References

Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.

  • F. P. Beer, E. R. Johnston, D. F. Mazurek, P. J. Cornwell, B. P. Self, Vector Mechanics for Engineers: Statics and Dynamics, McGraw Hill, 12th edition, 2019.
  • R. C. Hibbeler, Engineering Mechanics: Statics, Pearson, 15th edition, 2022 (published 2021).
  • J. L. Meriam, L. G. Kraige, J. N. Bolton, Engineering Mechanics: Statics, Wiley, 9th edition, 2018.
  • S. Timoshenko, D. H. Young, J. V. Rao, S. Pati, Engineering Mechanics (in SI units), McGraw Hill Education (India), 5th edition, 2013.
Suggest a correction

If something on this page is wrong, tell the editor. Your message is sent privately and is not published.

Sent privately to the Indiacon editor; not published.